Panasonic SC-HT1500 Manual de usuario

Setup Guide

perating Instructions

Recordable DVD

Home Theater System

Model No. SC-HT1500

Use only supplied speakers

Using other speakers can damage the unit and sound quality will be negatively affected.

FRONT SURROUND

SUBWOOFER CENTER

MAIN UNIT

Caution

≥The main unit and supplied speakers are

only to be used as indicated in this setup.

Failure to do so may lead to damage to the

amplifier and/or the speakers, and may

result in the risk of fire. Consult a qualified

service person if damage has occurred or

if you experience a sudden change in

performance.

≥Do not attempt to attach these speakers to

walls using methods other than those

described in this manual.

Set the speakers up on an even surface to prevent them from falling over.

Take proper precautions to prevent the speakers from falling over

if you cannot set them up on an even surface.

The angles in the diagram are approximate.

MAIN UNIT

STEP

Front and surround speaker assembly

Preparation

≥To prevent damage or scratches, lay down a soft cloth and perform assembly on it.

≥For assembly, use a Phillips-head screwdriver.

Attach the pipe to the large base.

1Thread the speaker cable through the base.

≥For quicker threading, fold the cable lightly in half (do not crease), pass the

folded portion through the hole in the base, and then pull through the rest

of the cable.

2Insert the pipe.

3Secure the pipe to the base.

Ensure the screw is securely fastened.

Attach the stands to the front and surround speakers.

≥There is no difference between the right and left speakers and stands.

≥Using the polyfoam and packaging cover included with this unit may ease attachment.

1Remove the mounting plate screw, and remove plate B. 2Place the pipe on plate A and attach plate B.

Rotate the pipe so that the flat side is facing away from the back of the

speaker.

3Secure the plate with the same screw removed in procedure 1.

Make sure you have all the

indicated components before

assembly, setup, and connection.

∏ Front speaker units ∏ Surround speaker units ∏ Pipes ∏ Large bases ∏ Washer screws

Groove

Cable

Hole for screw

Thread the speaker cable

through here.

Lessen excess

speaker cable.

Insert the pipe while slightly pulling on the speaker cable.

The supplied stands are specially designed for attachment to

Panasonic SB-FS1501 front speakers and SB-PS1501 surround

speakers. Only use as indicated in this setup.

Cable

Rear side of base

Washer screw

Mounting plate screw

Speaker Polyfoam

Packaging cover

Plate B

Plate A

[Note[

The stands with longer

cables are for the

surround speakers.

Fit the offset into the slot and slide

plate B into the locked position.

Offset

Slot

Plate B

Align the surface of plate B so that it

is even with the pipe surface.

Plate B

Pipe

Plate A

Supplied Accessories

Connect the speaker cables.

Adjust the speaker height.

≥Check the screws you tightened in procedures 1-3and 2 -3if the pipe and speaker are loose (➡page 2).

∫Front and surround speaker height (Assembled diagram)

Fasten the speaker cable.

≥Using the same polyfoam as done in procedure 2 will assist you in safely and securely fastening the speaker cables.

∫For rear side of speaker

∫For rear side of base

≥Twist off the vinyl ends of the speaker cable.

_: Copper

`: Silver Push !

Rear side of speaker

1Loosen the attached mounting plate screw

until the attached speaker is slightly loose

and adjustable.

Be careful not to loosen the screw too much

or the speaker may detach and fall.

2With one hand on the base, and the other

holding the speaker, adjust the height of

the speaker up and down.

Stopper screw

Screw to stop mounting plate from moving or sliding below

this point.

Phillips-head screwdriver

3Tighten the mounting plate screw

securely.

Speaker

1122.5 mm

Pipe

Base

You can adjust within this

range.

715.5 mm

Stopper screw

Do not remove.

For your reference

You can enjoy good acoustics by

adjusting the height of the front and

surround speakers to the height of

the television so the center position

of both are approximately the same.

Press the speaker cable

into the groove.

If there is any excess speaker

cable, thread the speaker

cable from the opening near

the top of the pipe while lightly

pulling the speaker cable from

the bottom of the base.

1Press the speaker cable and thread

between the hooks.

2Fit the speaker cable into the base cover groove

as far as possible.

Cable

STEP

Setup and connection of speakers

Preparation

Attach the stickers to the speaker cables.

≥In the same way, attach the sticker to the front speaker cable (R) and the

surround speaker cables (L, R).

Preparation

Check to make sure the washer screws on the bottom of the front and

surround speaker bases are not loose.

Positioning for best effect

How you set up your speakers can affect the bass and the sound field. Note

the following points.

≥Place the front, center, and surround speakers at approximately the

same distance from the seating position.

The angles in the diagram below are approximate.

≥Place speakers on flat secure bases.

≥Placing speakers too close to floors, walls, and corners can result in

excessive bass. Cover walls and windows with thick curtains.

[Note[

≥Set the speakers up on an even surface to prevent them from falling over.

Take proper precautions to prevent the speakers from falling over if you

cannot set them up on an even surface.

≥The left and right speaker pairs are the same with respect to the front and

surround speakers. Place each of the speakers in accordance with the

stickers you just attached.

≥Before moving the main unit, ensure the disc tray is empty.

Failure to do so will risk severely damaging the disc and the main unit.

∏ Sheet of speaker-cable

stickers

∏ Center speaker

cable (4 m cable)

∏ Front speakers ∏ Surround speakers ∏ Center speaker ∏ Subwoofer

e.g., For the front speaker (L) cable

Copper

Silver

About 10 cm About 10 cm

For the center speaker cable (4 m cable)

About 10 cm About 10 cm

Place the speakers.

Front speakers

Center speaker

≥Vibration caused by the center

speaker can disrupt the picture

if it is placed directly on the

television.

Put the center speaker on a

rack or shelf.

≥To prevent the speaker from

falling, do not place the speaker

directly on top of the television.

Main unit

[Note]

Keep your speakers at least 10 mm

away from the system for proper

ventilation.

Surround

speakers

(R)

(L) (R)

(L)

Subwoofer

Place to the right or left of the television on

the floor so that it won’t cause vibration.

Leave 10 cm at the rear for ventilation.

Notes on speaker use

≥Use only supplied speakers. Using other speakers can damage the unit

and sound quality will be negatively affected.

≥You can damage your speakers and shorten their useful life if you play

sound at high levels over extended periods.

≥Reduce the volume in the following cases to avoid damage.

–When playing distorted sound.

–When the speakers are receiving howling from a record player, noise

from FM broadcasts, or continuous signals from an oscillator, test disc, or

electronic instrument.

–When adjusting the sound quality.

–When turning the unit on or off.

≥Do not stand on the base and

shake the speaker. Be cautious

when children are near.

Connect the speaker cables to the subwoofer.

SUBWOOFER

2FRONT (R)

1FRONT (L)

4SURROUND (R)

3SURROUND (L)

5CENTER

Copper

Silver

Push!

Insert the wire fully.

Push !

Speaker-cable sticker

[Note]

≥Never short-circuit positive (i) and negative (j) speaker wires.

≥Be sure to connect only positive (copper) wires to positive (i) terminals and negative (silver) wires to negative

(j) terminals. Incorrect connection can damage the speakers.

Silver

Copper

If irregular coloring occurs on your television

The supplied speakers are designed to be used close to a television, but

the picture may be affected with some televisions and setup

combinations.

If this occurs, turn the television off for about 30 minutes.

The television’s demagnetizing function should correct the problem. If it

persists, move the speakers further away from the television.

STEP

Video connections

≥Before connection, turn off all equipment and read the appropriate operating instructions.

≥The equipment connections described are examples.

≥Peripheral equipment and optional cables sold separately unless otherwise indicated.

∫Recommended connection for your television

≥If your television does not have one of the terminals mentioned above, connect with the RF sockets only (➡page 7). However, when using this connection,

the picture received from a satellite receiver may not be clear, therefore we do not recommend it.

Q Link functions

Q Link offers a range of convenient functions (For further details ➡Operations Guide, page 55). Make sure to connect a fully wired 21-pin Scart lead to the

television if using the Q Link function.

The following systems from other manufacturers have similar functions to Q Link from Panasonic. For details, refer to your television’s operating instructions

or consult your dealer.

≥Q Link (registered trademark of Panasonic)

≥DATA LOGIC (registered trademark of Metz)

≥Easy Link (registered trademark of Philips)

≥Megalogic (registered trademark of Grundig)

≥SMARTLINK (registered trademark of Sony)

∫Do not connect the unit through a video cassette

recorder

Video signals fed through video cassette recorders will be affected by

the television.

≥When connecting to a television with a built-in VCR, connect to the input

terminals on the television side, not the VCR side.

What kind of input terminal does your television have? Required

cable(s)

Page No. for

connections

Page No. for TV

settings

Scart Highly recommended connection.

≥You can enjoy high-quality RGB video from this unit

by connecting to an RGB compatible television.

≥If your television has the Q Link feature, you can use

a variety of useful functions.

Fully wired 21-pin

Scart lead ➡7

➡11

≥If it’s a Q Link

television ➡10

Component

video

These terminals provide a purer picture than

the S-Video terminal.

≥If your television is compatible with progressive

scan, you can enjoy high-quality progressive video.

If you have a progressive compatible CRT television,

we cannot recommend this connection as some

flickering may occur.

3 video cables ➡8➡11

S-Video This terminal achieves a more vivid picture than the

video terminal. S-Video cable ➡8➡11

Audio/Video The most basic connection.

Audio/Video cable

➡8➡11

AV IN

COMPONENT

VIDEO IN

S-VIDEO IN

AUDIO IN

R L

VIDEO IN

Television Television

VCR

Main unit

VCR Main unit

≥When there is no 21-pin Scart terminal on the television (➡below or page 8).

≥Change the “AV2 Input” setting to match the output from a satellite receiver and set the “AV2 Connection” setting to “Normal” in the SETUP menu

(➡Operations Guide, page 50) after tuning is completed (➡page 10, 11).

∫To view satellite programmes

Press [HDD/DVD INPUT] to select the input channel “A2” for the satellite

receiver or put this unit in standby mode.

∫RGB

This refers to the three primary colours of light, red (R), green (G), and blue

(B) and also the method of producing video that uses them. By dividing the

video signal into the three colours for transmission, noise is reduced for

even higher quality images.

If you do not have a Satellite receiver, connect the aerial to the RF IN socket on this unit .

Connecting a television with 21-pin Scart terminal and Satellite receiver

OUT

OPTICAL

R-AUDIO-L

AV4 I N

LOOP

ANT

GND

LOOPEXT

AM ANT FM ANT

AUX

RF IN

RF OUT

COMPONENT

VIDEO OUT

(PROGRESSIVE/

INTERLACE)

AV1 ( T V)

AV2 (DECODER/EXT)

VIDEO S-VIDEO

S-VIDEOVIDEO

AV IN VHF/UHF

RF IN

DVD/VCR

To the aerial

Aerial lead

Cooling fan

RF coaxial lead

Fully wired 21-pin

Scart lead

Fully wired 21-pin Scart lead

AV1 terminal

If your television is equipped with RGB input capability, by connecting with a fully

wired 21-pin Scart lead you can see video using RGB output on this unit

(➡below). To output in RGB select “RGB (without component)” from “AV1 Output”

in the SETUP menu (➡Operations Guide, page 50) after tuning is completed

(➡page 10, 11).

Television

Satellite receiver

Main unit

Connecting a television with RF socket only and Satellite receiver

OUT

OPTICAL

R-AUDIO-L

AV4 I N

LOOP

ANT

GND

LOOPEXT

AM ANT FM ANT

AUX

RF IN

RF OUT

COMPONENT

VIDEO OUT

(PROGRESSIVE/

INTERLACE)

AV1 (TV)

AV2 (DECODER/EXT)

VIDEO S-VIDEO

S-VIDEOVIDEO

VHF/UHF

RF IN

RF OUT

RF IN

Satellite receiver

Main unit

Cooling fan

Television

To the aerial

RF coaxial lead

Aerial lead RF coaxial lead

∏ Main unit∏ RF coaxial lead ∏ Video cable

indicates included accessories.

indicates accessories not included.

STEP

Video connections

Connecting to the television using the 21-pin Scart leads (➡page 7).

∫Component video output

Component signal outputs the colour difference signals (PB/PR) and luminance signal (Y) separately in order to achieve high fidelity in reproducing colours. If

the television is compatible with progressive output, a high quality picture can be output because this unit’s component video output terminal outputs a

progressive output signal (➡Operations Guide, page 54).

For progressive output (➡Operations Guide, page 18)

≥Decoder here means the device used to decode scrambled broadcasts (Pay TV).

≥Change the “AV2 Input” and “AV2 Connection” settings in the SETUP menu to match the connected equipment (➡Operations Guide, page 50) after tuning

is completed (➜page 10, 11).

Connecting a television with VIDEO, S-VIDEO or COMPONENT VIDEO terminals and VCR

Connecting a digital receiver or decoder

OUT

OPTICAL

R-AUDIO-L

LOOP

ANT

GND

LOOPEXT

AM ANT FM ANT

AUX

RF IN

RF OUT

AV1 (TV)

AV2 (DECODER/EXT)

VIDEO S-VIDEO

S-VIDEOVIDEO

COMPONENT

VIDEO OUT

(PROGRESSIVE/

INTERLACE)

AV4 I N

S-VIDEO

VHF/UHF

RF IN

COMPONENT

VIDEO IN

S-VIDEO IN

VIDEO IN

VHF/UHF

RF IN

R L

AUDIO OUT

VIDEO

OUT

To the aerial

Splitter

Aerial

lead

Cooling fan

RF coaxial

lead

Audio/Video cable

You can also connect with the AV2

terminal on this unit using the 21-pin

Scart lead.

S-Video

cable

Video cable

Red White Yellow

Television

S-VIDEO OUT terminal

The S-VIDEO OUT terminal

achieves a more vivid picture than

the VIDEO OUT terminal. (Actual

results depend on the television.)

COMPONENT VIDEO OUT terminal

These terminals can be used for either interlace or

progressive output and provide a purer picture than the

S-VIDEO OUT terminal (➡below).

≥Connect to terminals of the same colour.

Use a splitter if you also

want to connect the aerial

to your VCR.

Main unit

Video cable

VCR

OUT

OPTICAL

R-AUDIO-L

AV4 I N

LOOP

ANT

GND

LOOPEXT

AM ANT FM ANT

AUX

RF IN

RF OUT

COMPONENT

VIDEO OUT

(PROGRESSIVE/

INTERLACE)

AV1 (TV)

AV2 (DECODER/EXT)

VIDEO S-VIDEO

S-VIDEOVIDEO

AV OUT

Digital receiver or decoder

21-pin Scart lead

Main unit

Cooling fan

indicates included accessories.

indicates accessories not included.

STEP

Radio and system connection

Connect the aerials.

(Optional FM aerial connection➡Operations Guide, page 45)

Connect the system cable.

Connect the AC mains leads.

≥Connect both AC mains leads to enjoy all the features of this system. (The

leads are the same.)

Conserving power

The main unit consumes a small amount of power, even when it is turned off

(approx. 7.5 W). To save power when the unit is not to be used for a long

time, unplug it from the household mains socket.

Set the unit to standby mode and remove the AC mains lead once

“BYE” disappears from the unit’s display.

You will need to reset some memory items in the unit after plugging.

[Note[

After making the connections perform radio tuning (➡Operations Guide,

page 44).

OUT

OPTICAL

R-AUDIO-L

AV4 I N

LOOP

ANT

GND

LOOPEXT

AM ANT FM ANT

AV1 (TV)

AV2 (DECODER/E

VIDEO S-VIDEO

S-VIDEOVIDEO

LOOP

ANT

GND

LOOPEXT

AM ANT FM ANT

AM loop aerial

Stand the aerial up

on its base.

Place the aerial

where reception is

best.

Keep loose aerial

cable away from

other wires and

cables.

Click!

FM indoor aerial

Adhesive tape

Affix this end of

the aerial where

reception is best.

Main unit

Push up.

Insert the aerial cables fully.

White Red

Tighten the terminal screw again.

Black

Loosen the terminal with a

Phillips-head screwdriver.

OUT

OPTICAL

R-AUDIO-L

AV4 I N

LOOP

ANT

GND

LOOEXT

AM A

VIDEO S-VIDEO

S-VIDEOVIDEO

LOOP

ANT

GND

LOOEXT

AM A

System cable

Catch

Catch is facing up Catch is facing down

Main unit

To disconnect

Press the catch and pull out.

BE SURE TO READ THE CAUTION FOR THE AC MAINS LEAD ON

PAGE 2 IN OPERATIONS GUIDE BEFORE CONNECTION.

Subwoofer

AC IN terminal

Main unit

AC mains leads

To household

mains socket

(AC 230–240 V,

50 Hz)

Lights when the main unit

turns on.

AC IN terminal

∏ System cable ∏ AM loop aerial ∏ FM indoor aerial ∏ AC mains leads

Subwoofer

STEP

Channel reception settings

Preparation

≥Confirm that the aerial is connected correctly.

≥Switch [HOME THEATER, TV] to “HOME THEATER”.

When connecting to a television that has the Q Link function

(➡Operations Guide, page 55) with a fully wired 21-pin Scart

lead (➡page 7).

You can download the tuning data from the television.

The unit’s Auto Clock Setting function will automatically synchronize the

time and date with that of the receiving station after tuning is completed.

1Turn on the television and select the

appropriate AV input to suit the

connections to this unit.

2Press [Í] to turn the unit on.

Downloading from the television starts.

3When downloading has been completed, the Owner ID settings

screen appears.

Press [1] and press the numbered buttons

to enter a 4-digit PIN number.

≥Make a note of the PIN number (don’t forget), as it is not possible to

return to the factory preset.

4Press [ENTER] twice to store the PIN

number.

The cursor moves to “Name”.

5Press [1].

6Press [3,4] to select a letter and then

press [1].

Repeat this to enter the name.

7Press [ENTER] to store the name.

8Press [4] and [1], and then repeat steps

6, 7 to enter and store “House No.” and

“Postcode”.

9Press [RETURN].

The Owner ID settings screen disappears.

To stop partway

Press [RETURN].

∫If the clock setting menu appears

Set the clock manually (➡Operations Guide, page 52).

∫To confirm that stations have been tuned correctly

(➡Operations Guide, page 51)

∫To restart Preset Download (➡Operations Guide,

page 51)

∫If you connect other equipment to AV2 terminal of this

unit

Change the “AV2 Input” and “AV2 Connection” in the SETUP menu to

match the connected equipment (➡Operations Guide, page 50).

∫If there is interference or a very poor picture appears

on the TV screen

Refer to “Removing Interference” (➡Operations Guide, page 17), and

perform steps 1, 2 and 4 to stop the RF output. In step 2, press [0] to select

“ss”.

Preset Download

(Setup with Q Link functions)

VOLUME

SKIP

STOP PAUSE PLAY/

SLOW/SEARCH

CANCEL

123

456

789

HOME THEATER TV

EXT LINK

MULTI REAR

DUBBING

S.POSITION

CREATE CHAP

C.FOCUS

REC MODE

CH SELECT

RETURN

ERASE

TIMER

TIME SLIP

AV2/OPT

TOP MENU

ENTER

DIRECT NAVIGATOR

FUNCTIONS

MIX

2CH

REC

TEST

MANUAL SKIP

REPEAT

MUTING

AUXFM/AMDVDHDD

DISPLAY

PRO LOGIC

VIDEO Plus +

SHIFT

DIRECT TV REC

FM MODE

SUB MENU

STATUS

EQ/SFC

PROG/CHECK

HDD/DVD INPUT

AUDIO

S W. LEVEL

-/--

A B C D

AUXHDD DVD

FM/AM

OPEN/CLOS E

UPDOWN

VOLUME

INPUT SELECTOR

REC

TIME SLIP

TUNE

CH CH

PULL-OPEN

RDS

3421

ENTER

RETURN

Í/I

Numbered

buttons

HOME

THEATER,

Download

Pos 4

Download in progress, please wait.

RETURN: to abort

RETURN

Owner ID

RETURN : leave

PIN number ¢¢¢¢

Name

House No.

Postcode

Otros manuales para SC-HT1500

Tabla de contenidos

Otros manuales de Sistema de cine en casa de Panasonic

Panasonic

Panasonic SCPM08 - DVD STEREO SYSTEM Manual de usuario

Panasonic

Panasonic SC-PT665 - 1000W 5 DVD Large Speaker Home Theater... Manual de usuario

Panasonic

Panasonic SC-XH170 Manual de usuario

Panasonic

Panasonic SC-HTB10P Manual de usuario

Panasonic

Panasonic SA-HT743P Manual de usuario

Panasonic

Panasonic SA-HT990E Manual de usuario

Panasonic

Panasonic SC-PT770 Manual de usuario

Panasonic

Panasonic SA-BT222EB Manual de usuario

Panasonic

Panasonic SC-HTB580 Manual de usuario

Panasonic

Panasonic SC-HT80 Manual de usuario

Panasonic

Panasonic SA-HT530GCP Manual de usuario

Panasonic

Panasonic SCPT750 - DVD HOME THEATER SOUND SYSTEM Manual de usuario

Panasonic

Panasonic SA-HT920P Manual de usuario

Panasonic

Panasonic SC-BTT195 Instrucciones de uso

Panasonic

Panasonic SC-MT1 Manual de usuario

Panasonic

Panasonic SC-DK3 Manual de usuario

Panasonic

Panasonic SA-HT440P Manual de usuario

Panasonic

Panasonic SCBT230 - BLU RAY HOME THEATER SYSTEM Instrucciones de uso

Panasonic

Panasonic SC-XH166 Manual de usuario

Panasonic

Panasonic SC-BTT362 Manual de usuario

Panasonic

Panasonic SCRT50 - HOME THEATER Manual de usuario

Panasonic

Panasonic SCPTX5 - DVD HOME THEATER SOUND SYSTEM Manual de usuario

Panasonic

Panasonic SAHT80 - RECEIVER W/ 5-DISK D Manual de usuario

Panasonic

Panasonic SC-BTT268 Manual de usuario

Manuales populares de Sistema de cine en casa de otras marcas

Samsung

Samsung HT-ES4200K Manual de usuario

Harman Kardon

Harman Kardon HS 100 Manual de usuario

Samsung

Samsung HT-P10 Manual de usuario

Philips

Philips HTS5131 Instrucciones de funcionamiento

Goodmans

Goodmans GDVD19SWS Manual de usuario

Moxi

Moxi media center Manual de usuario

Samsung

Samsung HT-EM35 Manual de usuario

LG HE903PAW Manual de usuario

Bose

Bose SoundTouch 520 Manual de usuario

Sony

Sony BDV-N990W Manual de usuario

Manta

Manta GK-500 Manual de usuario

Sharp

Sharp SBW800 Manual de usuario

Philips

Philips HTS3541 Manual de usuario

LG LHT799 Manual de usuario

Samsung

Samsung HT-TWZ415 Manual de usuario

Loewe

Loewe REFERENCE 52 SL FHD+ 200 NMP Manual de usuario

Samsung

Samsung AH68-02166R Manual de usuario

RCA

RCA 600-Watt Manual de usuario