Panasonic FV-10VEC2 Manual de usuario
FV-10VEC2
FV-10VEC2H
FV-10VE2
FV-10VE2H
CONTENTS
GENERAL SAFETY INFORMATION
DESCRIPTION
Model No.
2~3
READ AND SAVE THESE INSTRUCTIONS
Thank you for purchasing this Panasonic product.
Please read these instructions carefully before attempting to install, operate or service the
Panasonic product. Please carefully read the “GENERAL SAFETY INFORMATION” (P.2~3) of
this manual before use. Failure to comply with instructions could result in personal injury or
property damage. Please explain to users how to operate and maintain the product after
installation, and this booklet should be presented to users.
Please retain this booklet for future reference.
4
Installation and Operating Instructions
Energy Recovery Ventilator
WIRING DIAGRAM
WIRING METHOD
DUCT INSTALLATION
INSTALLATIONⅠ(WALL MOUNT)
INSTALLATIONⅠⅠ (CHAIN MOUNT)
START-UP PROCEDURE
OPERATION 13~15
TROUBLESHOOTING 18
MAINTENANCE 16~17
SPECIFICATIONS
PRODUCT SERVICE BACK COVER
19
7~8
5~6
8~11
12
13
4~5
10VC2M450A
2
This symbol is used to alert users not to disassemble the equipment.
When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring
and other hidden utilities.
Canada only: Not to be installed in a ceiling thermally insulated to a value greater than
R40.
Never install the unit in a high humidity space, such as a bathroom, kitchen or laundry
room.
Do not disassemble the unit. It may cause fire or electric shock.
Use this unit only in the manner intended by the manufacturer. If you have any
questions, contact the manufacturer.
Installation work and electrical wiring must be performed by qualified person(s) in
accordance with all applicable codes and standards, including fire-rated construction.
Do not install with a method which is not approved in the instructions.
Ducted fans must always be vented to the outdoors.
Solid state controls may cause harmonic distortion which can cause motor humming
noise. To reduce the risk of fire or electric shock, do not use this unit with any solid-
state control device.
This symbol is used to alert users to a specific operating procedure that must be
followed in order to operate the unit safely.
This symbol is used to alert users to a specific operating procedure that must not be
performed.
This symbol is used to alert users to make sure of grounding when using the
equipment with the grounding terminal.
For Your Safety
Explanation of symbol word panels
To reduce the risk of injury, loss of life, electric shock, fire, malfunction, and damage to
equipment or property, always observe the following safety precautions.
The following symbols are used to classify and describe the type of instructions to be
observed.
The following symbol word panels are used to classify and describe the level of hazard, injury,
and property damage caused when the denotation is disregarded and improper use is
performed.
CAUTION
Denotes a potential hazard that could result in death or
serious injury.
Denotes a hazard that could result in minor injury.
Denotes a hazard that could result in property damage.
WARNING
WARNING
GENERAL SAFETY INFORMATION
NOTICE
Ceiling joist and wall stud must be subjected to static load more than five times the
weight of the product.
The special-purpose or dedicated parts, such as mounting fixtures, must be used if such
parts are provided.
Do not kink the power cord.
The OA duct and EA duct must be connected directly to the outside.
Make certain that the electric service supply voltage is AC 120 V, 60 Hz.
These fans are intended for residential use only.
Do not install the unit where ducts are configured as shown below.
Adapter
Protect the power cord from sharp edges, oil, grease, hot surfaces, chemicals or other
objects.
When the product is to no longer be used, it must not be left in place but removed,
to prevent it from possibly falling.
Follow all local electrical and safety codes, as well as the National Electrical Code (NEC)
and the Occupational Safety and Health Act (OSHA).
Always disconnect the power source before working on or near the fan, motor, fixture
or wiring cover.
For general ventilating use only. Do not use to exhaust hazardous or explosive materials
and vapors.
Sufficient air is needed for proper combustion and exhausting of gases through the
flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating
equipment manufacturer’s guideline and safety standards such as those published by
the National Fire Protection Association (NFPA), and the American Society for Heating
Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
Excessive bending Successive bending Squeezed duct Bend close to duct adapter
3
Disconnect power by switching off wall switch first, then main switch and unplug
before working on unit when replacing the jumper cable with wall switch.
Install the unit in the area where air temperature is above 50 °F (10 °C) to avoid
condensation in unit.
Do not install the unit in the area where the air stream temperature may exceed 104 °F
(40 °C).
The unit must be installed in a mechanical room, basement, or other conditioned space.
CAUTION
GENERAL SAFETY INFORMATION
NOTICE
Energy Recovery Introduction: Compared to HRV (Heat Recovery Ventilator), ERV can also
transfer humidity and recover energy from that humidity. ERV can exchange energy
between “stale” EA and “fresh” OA, by transferring heat and moisture into the incoming cold
air, and pre-cooling and reducing the humidity of the incoming hot air. This helps maintain a
fresh environment even when the heating or cooling system is not operating.
<Heating> <Cooling>
Heat&
Moisture
Fresh air Fresh air
Exhaust air
(EA)
Outside air
(OA)
Exhaust air
(EA)
Outside air
(OA)
Stale air
Indoor
Stale air
Indoor
Outdoor Outdoor
4
DESCRIPTION
WIRING DIAGRAM
Heat&
Moisture
FV-10VEC2/FV-10VE2
OnlyFV-10VEC2
5
WIRING DIAGRAM
WIRING
METHOD
Open knock out hole
Junction box
For FV-10VEC2H, FV-10VE2H
Earth
ground
AC 120 60Hz (Power supply)
Neutral
Neutral
Earth
ground
Live
Live
WHITE
BLACK
GREEN
Wire Nuts
FV-10VEC2H/FV-10VE2H
OnlyFV-10VEC2H
R
JUNCTION BOX
GREEN
WHITE
BLACK
GROUND
NEUTRAL
LIVE
R G
G
Installation work and electrical wiring must be performed by qualified person(s) in
accordance with all applicable codes and standards, including fire-rated construction.
WARNING
6
WIRING
METHOD
HVAC/AHU signal
Wall Switches
(1)The terminal of wall switch has been connected by jumper cable as factory default.
If connecting with wall switch, please remove the jumper cable.
Note
(2)The HVAC/AHU signal cord is optional, please connect it when you want to control
the HVAC/AHU.
If connecting with HVAC/AHU, the HVAC/AHU will turn on while ERV turns on.
(3)If you are not connecting to the HVAC/AHU, please open knock-out holes for wall
switch and boost switch connection only.
(4)Insert wires into the corresponding terminals deeply through the ribs.
Make sure the screw of terminal securely fastens the copper wire and the copper
wire is not exposed.
(5)Reinstall the wiring cover and maintenance plate.
Open knock out holes
Maintenance plate
Wiring cover
Jumper cable
Unit: inches (mm)
Wall switch cord/
HVAC/AHU signal
cord/Boost switch
cord
Copper wire
1/4 (7)
3 1/2~4
(90~100)
CAUTION
The capacity of wall switch, boost switch should be more than 120 V~3 A to control
the power of the product.
INSTALLATIONⅠ(WALL MOUNT)
7
This method can be used in stud as below.
Unit: inches (mm)
Note
(1)Attach with flanged edge facing outward and edge without flange facing upward
when mounting wall bracket.
(2)Choose the mounting hole on wall bracket according to the distance between studs.
Unit: inches (mm)
A B
24 (609.6)
16 (406.4)
19 (482.6) 17 1/2 (444.5)
14 1/2 (368.3)
22 1/2 (571.5)
A
B
Stud
4-long screws
(ST4.2X30)
Stud
Wall bracket
Floor
Edge without flange
Flange
>31 1/2 (800)
24 (609.6)
16 (406.4)
19 (482.6)
2-screws
(M4X8)
4-screws
(M4X8)
L plate
Install L plates
HangerⅠ
Install HangerⅠ
Claw
24 (609.6)
16 (406.4)
19 (482.6)
Mount hangerⅠand L plates.
1
2
Mount wall bracket.
8
2-long screws
(ST4.2x30)
INSTALLATIONⅠ(WALL MOUNT)
4-plug covers
Control panel comes to this side
Wall bracket
MethodⅠ- Simplified ducted installation (Return method)
Note
DUCT INSTALLATION
This method draws return air from the return air duct
of the air furnace and supplies an equal amount of
outside air farther downstream into the return duct.
(1)The ERV unit must be balanced.
(2)
It is mandatory that HVAC/AHU signal cord be connected.
(3)Check local codes and authority having
jurisdiction for acceptance.
Note
(1)Must Have 2-3 ft straight run on all duct attachments points
before elbow is more than 2 ft (610 mm).
(2)Unit is normally balanced on high speed with the furnace blower on.
(3)A minimum separation of 40 inches (1 m) is recommended between the two
direct connections.
(4)The exhaust air connection shall be upstream of the supply air connection to
prevent exhausting any fresh air.
(5)The distance between two outdoor hoods please see P.11.
(6)The airflow must be confirmed on site using the balancing procedures found in P.13.
36”
Air
furnace
(914 mm)
Min.
Dampers for
balancing
airflows
40" (1 m) Min.
Outdoors
OA
EA
RA
SA
Return
air Return air
HangerⅠ
Hang ERV on to wall bracket.3
Please use 3rd hole
in case it is not easy to
put screws due to Junction box.
9
DUCT INSTALLATION
This method draws return air from specific points in the house and supplies an equal
amount of outside air into the return air duct of the air furnace.
Return air ducts of ERV should be installed in areas of the home where the poorest indoor
air quality exists (bathroom and kitchen).
The air furnace blower should be running when the ERV is operating to evenly distribute the
outside air throughout the house.
Method
ⅠⅠ
- Partially dedicated ducted installation
Note
(1)The ERV unit must be balanced.
(2)It is mandatory that HVAC/AHU signal cord be
connected.
(3)Check local codes and authority having
jurisdiction for acceptance.
Note
(1)Must Have 2-3 ft straight run on all duct attachments points before elbow is more
than 2 ft (610 mm).
(2)Unit is normally balanced on high speed with the furnace blower on.
(3)The distance between two outdoor hoods please see P.11.
(4)The airflow must be confirmed on site using the balancing procedures found in P.13.
Air
furnace
(914 mm)
Min.
Dampers for
balancing airflows
OA
EA
RA
SA
Outdoors
Return air
Return air36”
Return air from various parts of home.
(i.e. bathrooms, kitchens, utility areas)
10
DUCT INSTALLATION
This method draws return air from specific points in the
house and supplies outside air to specific locations of
the house. This system is not connected to an air
furnace.
Return air ducts should be installed in areas of the
home where the poorest indoor air quality exists (bath-
room and kitchen). Supply air ducts should be installed
to all bedrooms and living areas.
Method
ⅠⅠⅠ
- Fully dedicated ducted installation
Note
(1)The ERV unit must be balanced.
(2)Check local codes and authority having jurisdiction for acceptance.
Note
(1)Must Have 2-3 ft straight run on all duct attachments points before elbow
is more than 2 ft (610 mm).
(2)The distance between two outdoor hoods please see P.11.
(3)The airflow must be confirmed on site using the balancing procedures
found in P.13.
Outdoors
Return air from various parts of home
(e.g. bathrooms, kitchens, utility areas)
Supply air to main
living areas (e.g.
bedrooms, living
room)
OA
EA
RA
SA
Otros manuales para FV-10VEC2
1
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Admirador de Panasonic
Panasonic
Panasonic WhisperWelcome FV-05VFM2 Manual de usuario
Panasonic
Panasonic 2006ML-04W-B20 Manual de usuario
Panasonic
Panasonic FV-05-11VKS1 Guía de inicio rápido
Panasonic
Panasonic FV-05VS1 Manual de usuario
Panasonic
Panasonic Whisper-Lite FV-15VQL4 Manual de usuario
Panasonic
Panasonic FV-15ZY1 Manual de usuario
Panasonic
Panasonic FV-08VKME3 Manual de usuario
Panasonic
Panasonic FV-05VQ3 Manual de usuario
Panasonic
Panasonic F-302BH Manual de usuario
Panasonic
Panasonic F-60XDN Manual de usuario
Panasonic
Panasonic FV-05VFL4 Manual de usuario
Panasonic
Panasonic FV-04VE1 Manual de usuario
Panasonic
Panasonic FV-07VF1 Manual de usuario
Panasonic
Panasonic FV-051OVSCL1 Manual de usuario
Panasonic
Panasonic F-56UPG Manual de usuario
Panasonic
Panasonic FV-30BY1 Manual de usuario
Panasonic
Panasonic WhisperSense FV-08VQCL6 Manual de usuario
Panasonic
Panasonic WhisperCeiling FV-05 Manual de usuario
Panasonic
Panasonic FV-11VH1 Manual de usuario
Panasonic
Panasonic F-60MZ2 Manual de usuario
