Panasonic FV-07VF1 Manual de usuario

INSTALLATION

INSTRUCTIONS

Ventilating Fan

FV-05VF1 FV-07VF1

FV-09VF1 FV-11VF1

READ AND SAVE THESE INSTRUCTIOINS.

Please read these instructions carefully before attempting to install,

operate or service the Panasonic Ventilating Fan. Failure to comply

with instructions could result in personal injury and/or property

damage. Please retain this booklet for future reference.

III

Specifications

Dimensions

Description

9-12

Maintenance

Product Service

12-13

13-14

8-9

6-8

4-5

Table of Contents

Supplied Accessories

Unpacking

General Safety Information

Installation ( Joist Mounting )

Installation

( Wooden Header )

Installation

( In Existing Construction )

FV-05VF1

FV-07VF1

FV-09VF1

FV-11VF1

Thumb screw

Long screw

Quantity

Appearance

Part name

Grille

Suspension

bracket I

Suspension

bracket II

Screw

Suspension

bracket III

Clamp

Plate

3 inch adaptor

connector(optional

part for FV-05VF1

and FV-07VF1)

These Panasonic ceiling mount ventilating fan models use a low noise sirocco fan driven by a capacitor motor.

The motor is designed to have an extended service life with reduced energy consumption.

It also incorporates a thermal-cutoff for safety. The grille covering the main body is a spring-loaded,quick-remove

type. A damper for preventing couterflow is provided.

SUPPLIED ACCESSORIES

DESCRIPTION

Suspension plate II

Junction box cover

Junction box

Adaptor

Grille

Part name

330 (13)

84 (3 5/16)

DIMENSIONS

177.4 (7)

265~385 (10 13/32~15 5/32)

FV-05VF1

FV-07VF1

FV-09VF1

FV-11VF1

300.6(1

1 27/32 )

252.6 (9 15/16 )

79.2 (3 1/8)

56.7 (2 1/4)

105(4 1/8)

94 (3 23/32)

73 (2 7/8)

4 5

( 1 25/ 32 )

1 3 9 ( 5 1 5 / 3 2 )

(411/32)

110

255.6 (10 1 / 16 )

148 (5 13/16)

Unit: mm(inches)

No. No.

Body

Damper

Connector

Suspension bracket I

Thumb screw

3 inch adaptor connector

(only for FV-05VF1 and

FV-07VF1)

Bracket cover

Adaptor

4.2 (9.2)

3.9 (8.6)

20.0

Air direction

SPECIFICATIONS

GENERAL SAFETY INFORMATION

UNPACKING

Model No.

FV-05VF1

FV-07VF1

FV-09VF1

FV-11VF1

Exhaust

120

(W)

Power consumption

14.0

24.0

34.0

639

739

835

948

Speed

(RPM)

Air deliver at

0.1" WG(CFM)

110

Weight

Kg(Ib.)

4.1 (9.0)

* At 0.0" Static pressure, (Pa)

Unpack and carefully remove unit from carton.

Refer to the Supplied Accessories list to verify that all parts are present.

o o

1. Do not install this ventilating fan where air temperature may exceed 40 c (104 F).

2. Make certain that the electric service supply voltage is 120V, 60 Hz.

3. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and

the Occupation Safety and Health Act (OSHA).

4. Always disconnect the power source before working on or near the fan, motor or junction box.

5. Protect the power cord from sharp edges, oil, grease, hot surfaces, chemicals or other objects.

6. Do not kink the power cord.

7. Do not install the unit where ducts are configured as shown in Fig. A.

8. Provide suction parts with proper ventilation.

9. This unit is approved for use over a bathtub or shower when installed in a GFCI protected

branch circuit.

Fig. A

Floor

GENERAL SAFETY INFORMATION CONTINUED

CAUTION:

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

2. Not for use in cooking area. (Fig .B)

3. This product must be properly grounded.

Do not install above or

(Cooking area)

inside this area

equipment

Cooking

Fig. B

WARNING:

To reduce the risk of fire, electric shock or injury to persons, observe the following;

A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

B. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable

codes and standards, including fire-rated construction.

C. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning

equipment to prevent backdrafting. Follow the heating equipment manufacture's guideline and safety standards

such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating

Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

D. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

E. Ducted fans must always be vented to the outdoors.

F. These models are UL listed for tub and shower enclosures.

G. Solid state controls may cause harmonic distortion which can cause motor humming noise.

H. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warning device, shch as a tag, to the service panel.

I. NEVER place a switch where it can be reached from a tub or shower.

J. Not to be installed in a ceiling thermally insulated to a value greater than R40.

Fig. 3

Adaptor flange

Long screw

Fig. 1

4 Inch

Adaptor

Neutral

Green

Red

M.C.

Live

Power Supply

AC120V 60Hz

Black

3 inch adaptor connector

Duct tape

Connection method for 3 inch adaptor connector

IMPORTANT:

Remove the tape from damper and adaptor before

installation. As shown in Fig.1.

INSTALLATION I (JOIST MOUNTING)

1. Disconnect plug connector from receptacle before

starting installation.

2. Remove adaptor from body and secure to ceiling joists

using long screws. (Fig.2)

Keep the distance B (21.6mm,7/8 inch) for the thickness of

ceiling board.

Joist spacing A should be between 380mm(14 31/32inch) and

265mm(10 7/16 inch).

CAUTION:

Wiring diagram

3. Remove junction box cover and secure conduit to junction box

knock- out hole. (Fig.3)

4. Refer to wiring diagram below.

Using wire nuts, connect house power wires to ventilating fan

wires:black to black; white to white;green to green.

Replace the junction box cover.

5.Install circular duct (4 inch) or optional part (3 inch adaptor

connector) that is only for FV-05VF1 and FV-07VF1 and

secure it with duct tape.

CAUTION:

Mount junction box cover carefully so that lead wires are not

pinched.

Motor

Thermal Cutoff

Black Black

A.C.

Capacitor

White

Earth

White White

Green

Remove

tape

Damper

Suspension

bracket I

Ceiling joist

Adaptor

Ceiling joist

Duct

Junction box cover

Wire nut

Conduit

Junction box

Lead wires

Green wires

Fig. 2

Fan

Receptacle

Fig. 7

Thumb screw

Fig. 6

Ceiling joist

Claws

Adapter slots

Fan body

Adapter

Fig.5-5

Fig. 5-2

Fan body

Fig. 5-1

Adapter

When mounting

body and blower

separately

9. Connect plug connector to receptacle.(Fig.8)

Make sure that body "Claws" are property inserted into adaptor

slots.

IMPORTANT:

INSTALLATION I(JOIST MOUNTING)CONTINUED

6. Remove ceiling section. (Fig.4)

7. Insert fan body into ceiling. (Fig.6)

8. Secure fan body to adaptor using two thumb screws.(Fig.7)

1.Loosen 4 screws (but do

not remove them from

blower).(Fig.5-1)

2. Remove blower section.

3.Remove adaptor from

fan body and secure to

ceiling joists as in Fig.2

4.Insert fan body (without

blower section) into

ceiling.(Fig.6)

5.Secure the adaptor and

fan body using one thumb

screw as shown in Fig.5-3.

6.Secure the fan body to

the ceiling joists as shown

in Fig.9 and Fig.10 of

page 8.

7.Insert the blower into the

fan body.(Fig.5-4)

8.Secure the blower by 4

screws as shown in

Fig.5-5.

9.Mount the fan body with

thumb screw (on the right

side of bottom of the

adaptor) as shown in

Fig.7.

(Fig.5-2)

of page 6.

Screw

Blower

Fan body

Fig. 5-3

Ceiling joist

Fan body

Ceiling joist

Fig. 5-4

Screw

Screw driver

Ceiling

Ceiling joist

260 (10 1/ 4)

mm (inches)

260 (10 1/ 4)

Fig.4

Plug connector

Fig. 8

Fig.12

Fan body

Thumb screws

Ceiling

Mounting spring

Ceiling joist

Suspension bracket II

Suspension bracket III

Suspension bracket II

4-Long screws Suspension bracket III

1.Before installation, secure fan body to adaptor using two

thumb screws. (Fig.12)

INSTALLATION I(JOIST MOUNTING)CONTINUED

10. Secure fan body to ceiling joists using long screws in horizontal

direction with suspension bracket II and III.(Fig.9)

11. Secure suspension bracket II and III to the fan body using 2

screws(Fig.10)

12. Replace ceiling and insert mounting springs into slots as

shown and mount grille to fan body.(Fig.11)

INSTALLATION II (WOODEN HEADER)

Ceiling joist Fig.9

2-screws

Fig.10

Slot

Grille Fig.11

Live

Adaptor

mm (inches)

CAUTION:

Mount junction box cover carefully so that lead wires are not

pinched

INSTALLATION II (WOODEN HEADER) CONTINUED

2. Install header between ceiling joists using nails or screws.

3. Install the ventilating fan and secure with screws.(Fig.13 and Fig.14)

4. Insert the circular duct to the adaptor.

Remove the junction box cover and secure conduit to junction

box knockout hole (7/8 inch) (Fig.14 )

5. Refer to wiring diagram.

Using wire nuts,connect house power wires to ventilating fan wires:

black to black; white to white; green to green.

Replace the junction box cover.

Long screws

Junction box cover

Ventilating fan

Ceiling joist

Header

Ceiling joist

Wiring diagram

Adaptor

6. Finish ceiling work. Ceiling hole should be aligned with

edge of the flange. (Fig.15 )

7. Mount grille to fan body. (Fig.11, page 8.)

Circular duct

Fig.13

Fig.14

Ceiling

Flange

Fig.15

CAUTION:

To install the ventilating fan, follow the procedures described in lnstallation II. Take the following precautions before

installation.

1. Installation in existing construction.

Installing the ventilating fan in an existing building requires an accessible area (attic or crawl space) above the planned

installation location or existing ducting and wiring.

Check area above planned installation location to be sure that:

1. Duct work can be installed and that area is sufficient for proper ventilation.

2. Wiring can be run to planned location.

3. No wiring or other obstructions will interfere with installation.

Inspect duct work and wiring before proceeding with installation.

Plan suitable location for ventilating fan.(next to ceiling joist)

INSTALLATION III (IN EXISTING CONSTRUCTION)

Power Supply

AC120V 60Hz

Earth

Motor

Thermal Cutoff

Black Black Black

Red

Capacitor

White

Green

M.C.

A.C.

White White

Green

Neutral

Fig. 18

Ceiling

Adaptor

Long screws

Suspension bracket I

Fig. 17

Junction box cover

Conduit

Fig. 16

Ceiling joist

mm (inches)

Ceiling

Suspension bracket I

Secure adaptor to ceiling joists with 4 long screws inside

of the ceiling as shown in Fig.18.

Wiring diagram

CAUTION:

Check area above planned installation location to be sure that:

1. Ensure that the square hole size in ceiling should be sufficient according to Fig.16

2. Duct work can be installed and that area is sufficient for proper ventilation.

3. Wiring can be run to planned location.

4. No wiring or other obstructions will interfere with installation.

Before installation, provide inspection and maintenance access at a location that will not interfere with

installation work shown in installation II .

First, remove ceiling section according to Fig.4 of page 7.

Install ventilating fan.

2. Installation from accessible area above fan location.

Inspect duct work and wiring before proceeding with installation.

Remove ceiling section according to Fig.4 of page 7.

Install ventilating fan.

3. Installation without removing ceiling.

Loosen 4 screws (but do not remove them from blower) as

shown in Fig.5-1.

Remove blower from fan body as shown in Fig.5-2 of page 6.

remove adaptor from fan body.

Remove junction box cover and secure the existing conduit

to junction box knockout hole.(Fig.17)

Refer to wiring diagram on page 9.

Using wire nuts, connect house power wires to ventilating fan wires:

black to black; white to white; green to green.

Replace the junction box cover.

INSTALLATION III (IN EXISTING CONSTRUCTION) CONTINUED

Install circular duct(4 inch) or optional part (3 inch adaptor

connector) that is only for FV-05VF1 and FV-07VF1 and

secure it with duct tape as shown in Fig.17.

Live

Power Supply

AC120V 60Hz

Earth

Thermal Cutoff

Black

Red

Green

M.C.

A.C.

White

Neutral

Motor

Black Black

White White

Capacitor

If the location is in the middle between 2

joists, connect suspension bracket I and II

as shown below.

Suspension bracket II

260(10 1/4)

Duct

Ceiling joist

Otros manuales para FV-07VF1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Admirador de Panasonic

Panasonic

Panasonic WhisperCeiling FV-05 Manual de usuario

Panasonic

Panasonic F-60XDN Manual de usuario

Panasonic

Panasonic F-60WWK Manual de usuario

Panasonic

Panasonic WhisperGreen FV-08VKM3 Manual de usuario

Panasonic

Panasonic WhisperGreen FV-13VKM3 Manual de usuario

Panasonic

Panasonic FV-08VSL3 Manual de usuario

Panasonic

Panasonic RG-C1315LA Manual de usuario

Panasonic

Panasonic FV-05-11VKL1 Manual de usuario

Panasonic

Panasonic FV-05VFL4 Manual de usuario

Panasonic

Panasonic FV-08VKML1 Manual de usuario

Panasonic

Panasonic F-M15EC Manual de usuario

Panasonic

Panasonic FV-05VFL2 Manual de usuario

Panasonic

Panasonic FV-0511VFL1 Manual de usuario

Panasonic

Panasonic Whisper Green-Lite FV-08VKL1 Manual de usuario

Panasonic

Panasonic F-60TAN Manual de usuario

Panasonic

Panasonic WhisperSense FV-08VQCL5 Manual de usuario

Panasonic

Panasonic FV-0511VQCL1 Manual de usuario

Panasonic

Panasonic FV-15ZY1 Manual de usuario

Panasonic

Panasonic WhisperGreen FV-08VKML3 Manual de usuario

Panasonic

Panasonic F-M14HW Manual de usuario

Panasonic

Panasonic WhisperGreen FV-13VKS3 Manual de usuario

Panasonic

Panasonic FY-E15PM1 Manual técnico

Panasonic

Panasonic FV-10NLF1E Manual de usuario

Panasonic

Panasonic F-56XPG Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje

Litex Industries

Litex Industries E-CGL52CB5C1 Manual de usuario

Lindab

Lindab LTDF Manual de usuario