Panasonic CQDF802 Manual de usuario

Battery Notes

Remove and dispose of an old battery immediately.

Battery Information: ≥Battery type: Panasonic lithium battery (CR2025) (included)

≥Battery life: Approximately 6 months with normal use (at room temperature)

CQ-DF802W 17

CQ-DF802W

Before Use and Preparations

[PWR] (SOURCE)

≥Switches on/off the power. (➡page 20)

≥Selects a source. (➡page 20)

[BAND]

≥Selects a band. (➡page 22)

≥Pause CD playing. (➡page 25)

["] [#](Hour/minute/disc)

≥Selects (vertically) or adjusts an op-

eration or item.

≥Adjusts the clock. (➡page 21)

≥Selects disc. (➡page 28)

[%] [$] (Track/tune)

≥Selects (horizontally) or adjusts an

operation or item.

≥Selects or searches frequency/track.

(➡pages 22, 25, 28)

[SET]

≥Determines an operation or item.

["] [#] VOL (Volume)

≥Adjusts the sound volume.

(➡page 21)

[MUTE]

≥Lowers the volume. (➡page 21)

[RET] (RETURN)

≥Returns to the previous display in menu setting

mode.

[MENU]

≥Enters the menu setting mode.

≥Returnstotheregularmodeduringmenuplaysetting.

[FACE]

≥Selects the button color and display

brightness. (➡page 33)

[S·A] (Spectrum Analyzer)

≥Selects the Spectrum Analyzer display

pattern. (➡page 37)

[DISP] (Display)

≥Changes the display.

(➡pages 22, 25, 29)

[DIM] (DIMMER)

≥Changes the dimmer level.

(➡page 37)

[„] (NUMBER)

≥Enters the number input mode.

(➡pages 25, 29)

(S·HDB)

≥Sets the Super High Deﬁnition Bass

sound. (➡page 33)

RANDOM

SCAN

REPEAT

Car Audio

PWR

DISP

NUMBER

123

456

789

DIM

BAND

RET

SET

SOURCE

FACE

S • A

MUTE

VOL

RETURN

DIMMER

Battery Installation

1Remove the battery holder.

Pull the battery holder by the position B while pushing posi-

tion A in the direction indicated by the arrow.

2Install the battery on the battery holder.

As shown in the ﬁgure on the right, ﬁt the battery into the battery

holder with the “i” side facing up while pressing on position A.

3Insert the battery holder.

Push the battery holder back into its original position.

Back side Lithium battery (included)

Battery holder

Position A

Position B

≥Do not disassemble or short the battery. Do not throw a battery into a ﬁre.

≥Keep batteries away from children to avoid the risk of accidents.

≥Be careful to observe proper local disposal rules when you dispose of batteries.

Caution: Improper use of batteries may cause overheating, an explosion or ignition, resulting in injury or a

ﬁre. Battery leakage may damage the unit.

Point the remote control unit at the main unit’s sensor. (➡page 18)

[\ ]

Name of Controls Functions(Remote Control Unit)

[0] to [9]

≥Memorizes broadcast stations. (➡page 23)

≥Selects track/disc. (➡page 25, 29)

[4] (RANDOM)/[5] (SCAN)/[6] (REPEAT)

≥Selects listening item. (➡pages 26, 30)

❐Notes for the touch panel

When operating

≥You must use your ﬁngers to touch the panel and perform operations.

≥Do not press the buttons too forcefully. If you do so, you may damage or break the glass on the top surface

of the touch panel.

≥Do not allow the top surface of the touch panel to be caught by your ﬁngernails or any hard objects. If you

do so, you may damage or break the glass on the top surface of the touch panel.

≥Do not use a pen or other sharp implement to perform touch panel operations. If you do so, you may dam-

age or break the glass on the top surface of the touch panel.

≥Performing operations while the top surface of the touch panel is covered with dust may damage the glass

on the top surface of the touch panel.

When not operating

≥Be sure to keep the front panel with the removable face plate case (included) when it has been detached

from the main unit.

≥Take care not to drop the front panel when it has been detached from the main unit. Also take care not to

bump the top surface of the touch panel into anything. If you do so, you may break the glass on the top sur-

face of the touch panel.

≥Do not allow the top surface of the touch panel to be caught by your ﬁngernails or any hard objects. If you

do so, you may damage or break the glass on the top surface of the touch panel.

When cleaning (➡page 46)

❐You can operate this unit by pressing buttons on the main unit and the remote control unit, and touch pan-

els on the main unit.

≥Some operations can be activated by pressing buttons only on main unit or remote control unit.

Those cases are described in the instructions.

Example: Press [OPEN] on the main unit.

≥These instructions describe buttons that are concerned with operations as follows.

Example: Press [VOL "]or [VOL #]/["]or [#].

CQ-DF802W 19

(Display)

CQ-DF802W

Name of Controls Functions (Main Unit and Touch Panel)

Example: Press /["]or [#].

Example: Press /[MENU]/[DISP].

EXIT

[buttons on the main unit]/[remote control unit]

/[remote control unit]

(➡above.)

cursor on the touch panel

/[buttons on main unit]/[remote control unit]

(➡above.)

Spectrum Analyzer display on the touch panel

["] [#] VOL (Volume)

≥Adjusts the sound volume.

(➡page 21)

[MENU]

≥Enters the menu setting

mode.

≥Returns to the regular

mode during menu setting.

[BAND] (APM/;/1)

(Auto Preset Memory/Pause)

≥Selects a band. (➡page 22)

≥Pause CD playing.

(➡page 25)

≥Sets the auto preset memory

(APM) mode. (➡page 23)

[OPEN]

≥Opens the front panel.

(➡page 21)

['](Release)

≥Releases the front panel.

(➡page 52)

MUTE

(Indicates . )

≥Lowers the volume.

(➡page 21)

Dot display

(Indicates .)

≥Changes the display.

(➡pages 22, 25, 29)

≥Returns to the previous

display.

DISPLAY

Note:

≥Press the Spectrum Analyzer display to active the

cursor of the touch panel

VOL

CQ-DF802W

OPEN

BAND

APM/

;

MOSFET

50W

Display (➡next page)

Source display (Indicates .)

•Switches off the power. (➡page 20)

(Press and hold.)

•Selects a source. (➡page 20)

≥Radio ()

≥CD player mode

≥CD changer control

SOURCE

Spectrum Analyzer (S·A) display (➡page 36)

≥Clock basics (➡page 21)

, (Minute)

≥Radio mode (➡page 22)

(Preset)

•Enters a preset memory mode. (➡page 23)

≥CD player mode (➡page 24)

(Track)

≥CD changer control (➡page 28)

(Track),

≥Menu setting mode

•Returns to the previous display.

•Determines an operation or item in menu set-

ting mode.

Cursors

(Hour/minute/preset/disc/menu/submenu)

≥Selects (vertically) or adjusts an operation or

item.

≥Adjusts the clock. (➡page 21)

≥Selects a preset memory. (➡page 23)

≥Selects disc. (➡page 28)

(Tune/track/setting)

≥Selects (horizontally) or adjusts an operation or

item.

≥Selects or searches frequency/track.

(➡pages 22, 25, 28)

Disc slot

≥Loading the disc. (➡page 24)

[<] (Eject)

≥Ejects the disc. (➡page 24)

MUTE

Touch panel

≥Switches on the power.

(➡page 20)

Remote control sensor

Note:

≥Operations can be performed no

matter which part of the touch

panel is pressed BUT ONLY

WHEN THE POWER IS ON.

§The brightness of the screen illustrations in this manual is different from the actual screen brightness.

≥AUX-IN setting

≥Menu setting mode

•Returns to the previous display in

menu setting mode.

CQ-DF802W 21

CQ-DF802W

General

Mute/Attenuation

ON: Press /[MUTE]. ( indicator lights.)

OFF: Press /[MUTE]again.

Note:

≥After turning off the ignition key, a security message is displayed, and the panel removable alarm that

reminds you to take the panel is activated. (When security function is set to on ➡page 38)

≥Operations can be performed no matter which part of the touch panel is pressed BUT ONLY WHEN

THE POWER IS ON.

Volume

[VOL "]: Up

[VOL #]: Down

Setting range: 0 to 40

ACCON

Open/Close the Front Panel

OPEN: Press [OPEN] on the front panel.

CLOSE: Raise the panel by hand.

: No sound.

Caution:

≥To avoid damaging the front panel, do not push

it down or place objects on it while it is open.

≥Do not pitch your ﬁnger or hand in the front

panel.

≥Do not insert foreign matter into the disc slot.

["] [#]

VOL (Volume)

[PWR]

(SOURCE)

[DISP]

(Display)

[MUTE]

["] [#]

(Hour/minute)

RANDOM

SCAN

REPEAT

Car Audio

PWR

DISP

NUMBER

123

456

789

DIM

BAND

RET

SET

SOURCE

FACE

S •A

MUTE

VOL

RETURN

DIMMER

Power

Turn the key in the ignition until the accessory indicator lights.

∫ Power on

Press the touch panel on the main unit.

Press [PWR] (SOURCE) on the remote control unit.

∫ Power off

Press and hold on the main unit again for more than

1 second.

Press and hold [PWR] (SOURCE) on the remote control unit

again for more than 1 second.

SOURCE

Source

Press /(SOURCE) to change the source.

SOURCE

Note:

≥The sound level for each source is stored in

memory.

(There is one volume setting for AM radio

band, and one volume setting for FM radio

band.)

: Decrease the volume to 1/10.

Clock Basics

The 12-hour system is used for the clock.

Initial Time

1Press /[DISP] (display).

2Press and hold /[DISP] (display) for

more than 2 seconds.

3Press /["] or [#].

4Press /[DISP] (display).

5Press /["] or [#].

6Press /[DISP] (display).

DISPLAY

Note:

≥Press and hold /["] or [#]to

change numbers rapidly.

≥You can select the clock display during the unit

off. (➡page 38)

MUTE

(Hours blink.)

(Hours set.)

(Minutes blink.)

(Minutes set.)

(End.)

Decreasing volume range depends on setting.

(➡page 38)

(Hour/minute)

(Volume)

(Power off)

VOL

OPEN

SOURCE DISPLAY

[VOL "] [VOL #]

[OPEN]

Touch panel

(Power on)

BAND

APM/

;

MOSFET

50W X 4

Radio

CD player

CD changer control

AUX-IN setting

(When a CD is in the player.)

(When a CD changer is

connected and magazine is in

the changer.) ( page 28)

(Clock display)

Time Reset

Press and hold /[DISP] (display) for more

than 2 seconds to activate the time setting mode to

reset the time. Then, repeat steps 3to 6.

DISPLAY

SOURCE

DISPLAY

CQ-DF802W 23

CQ-DF802W

Radio

Band

Press [BAND] to change the band.

Radio Mode

Press /[SOURCE] to change to

the radio mode.

SOURCE

Tuning

/[$]: Up

/[%]: Down

Press and hold /[%]or [$] for

more than 0.5 seconds, then release.

Seeking will start.

Radio mode display

FM stereo indicator

Display Change

Press /[DISP] (display) to change the display.

DISPLAY

Radio mode display

(Default)

Clock display

One-Touch Selection of a Station

Up to 6 stations each can be saved in the FM1, FM2, FM3 and AM preset station memories.

Manual Preset

Memory

Manually save a station in

the preset memory.

Entering numbers directly on the remote control unit

1Select a band and frequency (step 1, 2and 3on the previous

page).

2Press and hold [1] to [6] for more than 2 seconds to memorize.

Auto Preset

Memory (APM)

Automatically save rela-

tively strong stations in

the preset memory.

1Select a band (steps 1and 2 on the

previous page).

2Press and hold [BAND] (APM) for

more than 2 seconds.

Note:

≥Existing saved stations are overwritten with new stations after following this procedure.

Preset Station

Calling

1Select a band (steps 1and 2on the previous page).

2Press the Spectrum Analyzer display to show (preset)

3Press /["]or [#]to select the preset number for tuning

in the preset station.

(Press [1] to [6] on the remote control unit.)

P.SETTUNE

Note:

≥Frequency setting can be performed even after selecting a preset num-

ber.

1Select a band and frequency (steps 1, 2and 3on the previous

page).

2Press and hold the Spectrum Analyzer display for more than

2 seconds until the preset number blinks.

3Press /["]or [#]to select a preset number (1j6).

4Press and hold (preset) for more than 2 seconds to memo-

rize. P.SET

TUNE

Scanning:

≥The display blinks once, and a re-

ceiving station is saved in the

memory.

Preset number

≥The 6 strongest available stations will be automatically saved in the

memory under preset number 1to 6.

≥Once set, the preset stations are sequentially scanned for 5 seconds

each. (Scanning)

≥Press /["]or [#]for the broadcast you want to listen

to.

(Press [1] to [6] on the remote control unit.)

Band

(SOURCE)

[DISP]

(Display)

[%] [$]

(Tune)

["] [#]

(Preset station/

select)

[BAND]

(Auto preset

memory)

[1] to [6]

(Preset station)

RANDOM

SCAN

REPEAT

Car Audio

PWR

DISP

NUMBER

123

456

789

DIM

BAND

RET

SET

SOURCE

FACE

S •A

MUTE

VOL

RETURN

DIMMER

Frequency

VOL

SOURCE DISPLAY

P.SET

(Preset)

(Preset station/select)

(Tune)

BAND

APM/

;

MOSFET

50W

TUNE

Caution:

≥To ensure safety, never attempt to preset sta-

tions while you are driving.

P.SET

Note:

≥:

Displays when not have any

menu settings. Radio and AUX-

IN mode do not have any menu

settings.

≥Press or to

change the cursor.

P.SETTUNE Spectrum Analyzer display

SOURCE

DISPLAY

CQ-DF802W 25

CQ-DF802W

CD Player

Note:

≥Loading a disc when the power is off allows the

power to be turned on.

Open the front panel.

Press [OPEN] on the front panel.

Insert the disc.

Playback will start automatically after the

unit recognized the loaded disc as an ordi-

nary music CD. (When a CD-R or CD-RW

which has CD-DA formatted data as the

same as an ordinary music CD is loaded,

this unit recognizes it as an ordinary music

CD.)

Close the front panel manually.

Disc Insert and Playback

Stop and Disc Eject

1Press [OPEN] on the front panel.

2Press [<] (eject) to stop CD play and eject the

disc.

Label side

(Eject)

<Close

CD player mode display

≥Do not insert a disc when “DISC”indi-

cator lights.

≥Lights when the disc is loaded/played.

Caution:

≥Only 12 cm CD, CD-DA data recorded CD-R and CD-RW discs are available for this unit.

≥This unit does not support CD text display.

≥This unit does not support MP3 disc playback.

≥Refer to page 47 about notes on CD-Rs/RWs.

≥To avoid damaging the front panel, do not push it down or place objects on it while it is open.

≥Do not use irregular shaped discs.

≥Do not use discs that have a seal or label attached.

≥Do not insert foreign matter into the disc slot.

≥The back side of the front panel becomes hot during use, but this is not an indication of any problem. Do

not touch anything here except [<] (eject).

≥The disc insertion slot and its vicinity become hot, but this is not an indication of any problem. Be care-

ful when inserting a disc or pressing [<] (eject).

Track Selection

/[$]: Advance to the next track.

/[%]: Back to the beginning of the current track.

Back to the previous track. (Press twice.)

Pause

Press [BAND] (;/1).

Press [BAND] (;/1) again to cancel.

Listening to a CD

Track Search

Press and hold.

/[$]: Fast forward

/[%]: Fast backward

Release to resume the regular play.

Direct Track Selection

Example: track number 10

1Press [„] (NUMBER).

2Press [1] [0].

3Press [SET] to set.

The corresponding track starts playing.

Display Change

Press /[DISP] (display) to change the dis-

play. DISPLAY

Track number/track

playing time (Default)

Clock display

CD Player Mode

(When a CD is in the player.)

Press /[SOURCE] to change to CD

player mode.

Playback starts automatically.

SOURCE

(SOURCE)

[DISP]

(Display)

[%] [$]

(Track)

[SET]

[BAND] (Pause)

[„]

(NUMBER) [0] to [9]

(Track number)

RANDOM

SCAN

REPEAT

Car Audio

PWR

DISP

NUMBER

123

456

789

DIM

BAND

RET

SET

SOURCE

FACE

S •A

MUTE

VOL

RETURN

DIMMER

Note:

≥Press /[DISP] (display) or [„] (NUM-

BER) to return to the regular mode.

≥If a non-existent track number is input and en-

tered, the command is invalid and the display re-

turns to regular mode.

DISPLAY

Track playing time

Track number

(Track)

VOL

OPEN

SOURCE DISPLAY

[BAND] (;/1) (Pause)

[OPEN]

BAND

APM/

;

MOSFET

50W X 4

Note:

≥Ejecting the disc when the unit is in the CD player

mode allows the power to be turned off.

Only for the remote control unit

Repeat and random indicator

SOURCE

DISPLAY

CQ-DF802W 27

CQ-DF802W

CD Player (Continued)

Menu Setting on CD Player Mode

Random Play

Default: RAND OFF

Repeat Play

Default: REP OFF

Press /["]or [#]to change setting.

12 3Menu Submenu Setting

Scan Play

Default: Off

1Press /

[%]or [$]to select

“RANDOM”.

2Press /[SET] to set.

SET

1Press /

[%]or [$]to select

“REPEAT”.

2Press /[SET] to set.

SET

: All the available track plays in a random

sequence.

: Cancel

Press /["]or [#]to change setting.

: Repeat the current track.

: Cancel

Direct setting on the re-

mote control unit when the

menu is not displayed

Press [4] (RANDOM) to

change setting.

On: “RAND”lights.

Off:(Displayed for 2 seconds.)

Press [6] (REPEAT) to change

setting.

(When you press a button, the

screen on the left is displayed

for 2 seconds.)

Note:

≥Press /[MENU]/[MENU], [DISP] (display) to

return to the regular mode.

≥Press /[RET] (RETURN) to return to the previ-

ous display.

≥REP: Lights during repeat play.

RAND: Lights during random play.

RTN

EXIT

Only for the remote control unit

Press [5] (SCAN) to change setting.

On: The ﬁrst 10 seconds of each track plays in sequence.

Off: Cancel

: Lights during menu play setting.

: Lights during CD player menu mode.

[%] [$]

(Menu/submenu)

["] [#]

(Setting)

[SET]

[MENU]

[4] (RANDOM)

[5] (SCAN)

[6] (REPEAT)

[DISP] (Display)

RANDOM

SCAN

REPEAT

Car Audio

PWR

DISP

NUMBER

123

456

789

DIM

BAND

RET

SET

SOURCE

FACE

S •A

MUTE

VOL

RETURN

DIMMER

Blinks.

VOL

SET

[MENU]

BAND

APM/

;

MOSFET

50W

VOL

SET

(Submenu)

BAND

APM/

;

BAND

APM/

;

2112

MOSFET

50W

VOL

EXIT

MOSFET

50W

[MENU]

RTN (Setting)

BAND

APM/

;

3Setting

1Press [MENU] during CD

playing to display “MODE”.

2Press /[SET] to set.

SET

1Menu 2Submenu

When the menu is not displayed

(Displayed for 2 seconds.)

Track Search

Press and hold.

/[$]: Fast forward

/[%]: Fast backward

Release to resume the regular play.

CQ-DF802W 29

CQ-DF802W

CD Changer Control

CD changer functions are designed for optional Panasonic CD changer unit.

Preparation:

≥Connect the CD changer, and load a magazine (disc).

Note:

≥Loading a magazine when the power is off allows the power to be turned on.

≥Ejecting the magazine when the unit is in the CD changer mode allows the power to be turned off.

≥This unit does not support CD-ROM, CD-R or CD-RW playback through the CD changer. Use the CD changer

to listen to normal music CD exclusively.

≥Pausing does not function in the CD changer mode.

CD Changer Mode

(When a CD changer is connected and a maga-

zine is in the changer.)

Press /[SOURCE] to

change to CD changer mode.

Playback starts automatically.

Note:

≥: Load a magazine with CDs.

≥: Magazine is ejected in the

CD changer mode.

SOURCE

Disc Selection

/["]: Next disc.

/[#]: Previous disc.

(SOURCE)

[DISP]

(Display)

[%] [$] (Track)

["] [#] (Disc)

[SET]

[„]

(NUMBER)

[0] to [9]

(Disc number)

RANDOM

SCAN

REPEAT

Car Audio

PWR

DISP

NUMBER

123

456

789

DIM

BAND

RET

SET

SOURCE

FACE

S •A

MUTE

VOL

RETURN

DIMMER

CD changer mode display

≥Lights when the changer (magazine) is con-

nected.

≥Lights when the disc is played.

Track Selection

/[$]: Advance to the next track.

/[%]: Back to the beginning of the current track.

Back to the previous track. (Press twice.)

Direct Disc Selection

Example: disc number 10

1Press [„] (NUMBER).

2Press [1] [0].

3Press [SET] to set.

The ﬁrst track of the corresponding disc starts

playing.

Display Change

Press /[DISP] (display) to change the dis-

play. DISPLAY

Disc/track number (Default)

Track playing time

Clock display

Note:

≥Press /[DISP] (display) or [„] (NUM-

BER) to return to the regular mode.

≥If a non-existent disc number is input and en-

tered, the command is invalid and the display re-

turns to regular mode.

DISPLAY

Note:

≥Press /[DISP] (display) to return to the

regular mode.

DISPLAY

Disc number Track number

DISC

(Track)

TRC

VOL

SOURCE DISPLAY

(Disc)

(Track)

BAND

APM/

;

MOSFET

50W X 4

≥Press or to change

the cursor. TRCDISC

Only for the remote control unit

Repeat and random indicator

SOURCE

DISPLAY

CQ-DF802W 31

CQ-DF802W

CD Changer Control (Continued)

Menu Setting on CD Changer Mode

Random Play

Default: RAND OFF

Scan Play

Default: Off

12Menu Submenu

Repeat Play

Default: REP OFF

1Press [MENU] during CD

changer playing to display

“MODE”.

2Press /[SET] to set.

SET 1Press /

[%]or [$]to select

“RANDOM”.

2Press /[SET] to set.

SET

Disc Random Play

Default: D-RND OFF

1Press /

[%]or [$]to select

“D-RANDOM”.

2Press /[SET] to set.

SET

1Press /

[%]or [$]to select

“REPEAT”.

2Press /[SET] to set.

SET

Disc Scan Play

Default: Off

Disc Repeat Play

Default: D-REP OFF

1Press /

[%]or [$]to select

“D-REPEAT”.

2Press /[SET] to set.

SET

Press /["]or [#]to change setting.

3Setting

: All the available tracks on all discs

plays in a random sequence.

: Cancel

Press /["]or [#]to change setting.

: All the available tracks on the current

disc plays in a random sequence.

: Cancel

Press [5] (SCAN) to change set-

ting.

Press /["]or [#]to change setting.

: Repeat the current track.

: Cancel

Press /["]or [#]to change setting.

: Repeat the current disc.

: Cancel

Press and hold [5] (SCAN) for

more than 2 seconds to change

setting.

Direct setting on the remote con-

trol unit when the menu is not

displayed

Press [4] (RANDOM) to change setting.

On: “RAND”lights.

Off:(Displayed for 2 seconds.)

Press and hold [4] (RANDOM) for

more than 2 seconds to change setting.

On: “RAND”blinks.

Off:(Displayed for 2 seconds.)

Press [6] (REPEAT) to change setting.

(When you press a button, the

screen on the left is displayed for

2 seconds.)

Press and hold [6] (REPEAT) for more

than 2 seconds to change setting.

(When you press a button, the

screen on the left is displayed for

2 seconds.)

Note:

≥Press /[MENU]/[MENU], [DISP] (display) to

return to the regular mode.

≥Press /[RET] (RETURN) to return to the previ-

ous display.

≥REP: Lights during repeat play.

Blinks during disc repeat play.

RAND: Lights during random play.

Blinks during disc random play.

RTN

EXIT

Only for the remote control unit

: Lights during menu play setting.

: Lights during CD changer menu mode.

On: The ﬁrst 10 seconds of each track on all

discs plays in sequence.

Off: Cancel

On: The ﬁrst 10 seconds of the ﬁrst track of all

the discs plays in sequence.

Off: Cancel

Blinks.

[%] [$]

(Menu/

submenu)

["] [#]

(Setting)

[SET]

[MENU]

[4] (RANDOM)

[5] (SCAN)

[6] (REPEAT)

[DISP]

(Display)

RANDOM

SCAN

REPEAT

Car Audio

PWR

DISP

NUMBER

123

456

789

DIM

BAND

RET

SET

SOURCE

FACE

S •A

MUTE

VOL

RETURN

DIMMER

VOL

SET (Submenu)

VOL

SET

MOSFET

50W

[MENU]

BAND

APM/

;

BAND

APM/

;

2112

MOSFET

50W

VOL

EXIT

MOSFET

50W

[MENU]

RTN (Setting)

BAND

APM/

;

1Menu 2Submenu 3Setting

When the menu is not displayed

(Displayed for 2 seconds.)

CQ-DF802W 33

CQ-DF802W

Front Panel Settings [FACE]

Front Panel Brightness

The brightness of the screen can be ad-

justed to the desired level so that it will ﬁt

in with the equipment inside the car and

the front panel buttons.

Default: OPEN

Setting range: OPEN, HALF, CLOSE

Color Change

You can change the color of the [VOL "

#] [MENU] [BAND] buttons.

Default: 7COLOR

Variety: 5 kinds, LEVEL, 7COLOR

12Menu Submenu

1Press [MENU].

2Press /

[%]or [$]to select

“FACE”.

3Press /[SET] to set.

SET

1Press /

[%]or [$]to select

“SHUTTER”.

2Press /[SET] to set.

SET

1Press /

[%]or [$]to select

“COLOR”.

2Press /[SET] to set.

SET

Press /["]or [#]to change setting.

3Setting

Press /["]or [#]to change setting.

Audio and Sound Settings [AUDIO]

S·HDB (Super High

Deﬁnition Bass)

Especially for rock music, the bass-sound

will be more powerful.

Default: S·HDB OFF

Setting range: S·HDB OFF, BOOM, TIGHT

12Menu Submenu

1Press [MENU].

2Press /

[%]or [$]to select

“AUDIO”.

3Press /[SET] to set.

SET

1Press /

[%]or [$]to select

“S·HDB”.

2Press /[SET] to set.

SET

: Lights during menu play setting.

: Lights during FACE mode.

: Lights during AUDIO mode.

3Setting

: The bass sounds of the speakers are strongly

emphasized. “(”lights.

: The bass sounds of the speakers are moder-

ately emphasized. “(”lights.

(The sounds of the subwoofer can be heard

clearly.)

: S·HDB is non-active.

Direct setting on the re-

mote control unit when the

menu is not displayed

Press (S·HDB) to change

setting.

(When you press a button,

the screen on the left is dis-

played for 2 seconds.)

Note:

≥Press /[MENU]/[MENU], [DISP] (display) to

return to the regular mode.

≥Press /[RET] (RETURN) to return to the previ-

ous display.

RTN

EXIT

: 5 kinds (below),

white and yellow

: Changes according

to the volume level.

: Red

: Purple

: Blue

: Aqua blue

: Green

Direct setting on the re-

mote control unit when the

menu is not displayed

Press and hold [FACE] for

more than 2 seconds to

change setting.

(When you press a button,

the screen on the left is dis-

played for 2 seconds.)

Press [FACE] to change set-

ting.

(When you press a button,

the screen on the left is dis-

played for 2 seconds.)

[\ ]

VOL

MOSFET

50W

SET (Submenu)

VOL

SET

MOSFET

50W

[MENU]

(Menu)

BAND

APM/

;

BAND

APM/

;

112

223

MOSFET

50W

VOL

EXIT

MOSFET

50W

[MENU]

RTN (Setting)

BAND

APM/

;

1Menu 2Submenu 3Setting

: Bright (brighter than “HALF”)

: The entire front panel darkens and the illuminated

colors inside the panel change in appearance.

: Bright

The brightness of the entire front

panel changes.

(See page 36 for information on changing

the brightness of just the display area.)

VOL

OPEN

BAND

APM/

;

MOSFET

50W

VOL

OPEN

BAND

APM/

;

CQ-DF802W 35

CQ-DF802W

Audio and Sound Settings [AUDIO] (Continued)

Bass and Treble

You can adjust the bass and treble sound.

Default: BAS (Bass) 0 dB

TRE (Treble) 0 dB

Setting range: j12 dB to i12 dB

(by 2 dB)

Balance and Fader

You can adjust the sound balance among

the front, rear, right and left speakers.

Default: BAL (Balance) CNT (Center)

FAD (Fader) CNT (Center)

Setting range: 15 levels each

Subwoofer Level

You can change the subwoofer volume level.

Default: 0 dB

Setting range:j∞(subwoofer mute),

j6 dB to i6 dB (by 2 dB)

Subwoofer Low Pass Filter

Select the upper limit frequency of the

sound from subwoofer.

Default: 120 Hz

Setting range: 120 Hz/80 Hz

12Menu Submenu

1Press [MENU].

2Press /

[%]or [$]to select

“AUDIO”.

3Press /[SET] to set.

SET

1Press /

[%]or [$]to select

“BASS”.

2Press /[SET] to set.

SET

1Press /

[%]or [$]to select

“TREBLE”.

2Press /[SET] to set.

SET

1Press /

[%]or [$]to select

“BALANCE”.

2Press /[SET] to set.

SET

1Press /

[%]or [$]to select

“FADER”.

2Press /[SET] to set.

SET

1Press /

[%]or [$]to select

“SUB-W LEV”.

2Press /[SET] to set.

SET

1Press /

[%]or [$]to select

“SUB-W FRQ”.

2Press /[SET] to set.

SET

3Setting

Press /["]or [#]to adjust the level.

/["]: Increase the bass.

/[#]: Decrease the bass.

Press /["]or [#]to adjust the level.

/["]: Increase the treble.

/[#]: Decrease the treble.

Press /["]or [#]to adjust the level.

/["]: Right enhanced.

/[#]: Left enhanced.

Press /["]or [#]to adjust the level.

/["]: Front enhanced.

/[#]: Rear enhanced.

Press /["]or [#]to adjust the level.

/["]: Increase the level.

/[#]: Decrease the level.

Press /["]or [#]to change the setting 120 Hz

or 80 Hz.

Note:

≥Press /[MENU]/[MENU], [DISP] (display) to

return to the regular mode.

≥Press /[RET] (RETURN) to return to the previ-

ous display.

RTN

EXIT

: Lights during menu play setting.

: Lights during AUDIO mode.

[%] [$]

(Menu/submenu)

["] [#]

(Setting)

[SET]

[MENU]

[DISP] (Display)

RANDOM

SCAN

REPEAT

Car Audio

PWR

DISP

NUMBER

123

456

789

DIM

BAND

RET

SET

SOURCE

FACE

S •A

MUTE

VOL

RETURN

DIMMER

VOL

SET (Submenu)

VOL

SET

MOSFET

50W

[MENU]

(Menu)

BAND

APM/

;

BAND

APM/

;

223211

MOSFET

50W

VOL

EXIT

MOSFET

50W

[MENU]

RTN (Setting)

BAND

APM/

;

1Menu 2Submenu 3Setting

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema estéreo para automóvil de Panasonic

Panasonic

Panasonic CY-EM100U Manual de usuario

Panasonic

Panasonic CQ-RD333N Manual de usuario

Panasonic

Panasonic CQDVR592U - AUTO RADIO/CD/DVD PL Manual de usuario

Panasonic

Panasonic CQ-R233WJ Manual de usuario

Panasonic

Panasonic CQ-JT1010X Manual de usuario

Panasonic

Panasonic CQ-VD6503W Manual de usuario

Panasonic

Panasonic CQDP103U - AUTO RADIO/CD DECK Manual de usuario

Panasonic

Panasonic CQ-C8401W Manual de usuario

Panasonic

Panasonic CQ-RDP133N Manual de usuario

Panasonic

Panasonic CQC3405U - AUTO RADIO/CD DECK-MULTI LANG Manual de usuario

Panasonic

Panasonic CQ-C7402W Manual de usuario

Panasonic

Panasonic RM-G30EAG Manual de usuario

Panasonic

Panasonic CQC1101U - AUTO RADIO/CD DECK Manual de usuario

Panasonic

Panasonic CQDP383U - AUTO RADIO/CD DECK Manual de usuario

Panasonic

Panasonic CQ-MR505N Manual de usuario

Panasonic

Panasonic CQ-JA1920L Manual de usuario

Panasonic

Panasonic CQ-C7413U? CQ-C7113U Manual de usuario

Panasonic

Panasonic CQCB9900U - AUTO RADIO/CD DECK Manual de usuario

Panasonic

Panasonic RD-1103 Manual de usuario

Panasonic

Panasonic CQ-RD243N Manual de usuario

Panasonic

Panasonic CQDF783U - AUTO RADIO/CD DECK Manual de usuario

Panasonic

Panasonic CQDP171U - AUTO RADIO/CD DECK Manual de usuario

Panasonic

Panasonic CQ-C3400W Manual de usuario

Panasonic

Panasonic C7301U - Cd Rcvr W/ Custm Dsply Manual de usuario

Manuales populares de Sistema estéreo para automóvil de otras marcas

JL Audio

JL Audio Stealthbox SB-CAN-G2MVX3D/10TW3 Manual de usuario

Clarion

Clarion PU-9836A Manual de usuario

Sony

Sony MEX-BT5750U Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AR0M Manual de usuario

Sony

Sony RM-X7BT Manual de usuario

Insignia

Insignia NS-HD5113 Manual de usuario

Clarion

Clarion BTD3341 Manual de usuario

USA SPECS

USA SPECS PA11-VW6 Manual de usuario

Sony

Sony MEX-N4380BT Manual de usuario

Kenwood

Kenwood KCD-BT6544U/UY Manual de usuario

JVC

JVC KD-DB912BT Manual de usuario

Philips

Philips CSQ405/98 Manual de usuario

Alpine

Alpine TDM-7544 Manual de usuario

Autotek

Autotek TransAm TA 1400 Manual de usuario

Clarion

Clarion PN-3124N-A Manual de usuario

Denso TEN

Denso TEN FT0108A Manual de usuario

Pyle

Pyle PLD57MU Manual de usuario

Harman

Harman Chrysler Radio Navigation System RB4 Manual de usuario