Panasonic WV-QDC500S Manual de usuario
For U.S. and Canada:
Panasonic i-PRO Sensing Solutions
Corporation of America
800 Gessner Rd, Suite 700 Houston, TX 77024
https://www.security.us.panasonic.com/
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada
1-877-495-0580
https://www.panasonic.com/ca/
© Panasonic i-PRO Sensing Solutions Co., Ltd. 2020
For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com
Panasonic i-PRO Sensing Solutions Co., Ltd.
Fukuoka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Operating Instructions
Included Installation Instructions
Dome Cover
Model No.
WV-QDC500S
• Before attempting to connect or install this product, please read these instructions carefully and
save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual product
within the scope that will not interfere with normal use due to improvement of the product.
Ns0620-0
Printed in China
Preface
This smoke type dome cover (approx. 45 % of transmittance) is used to install the indoor/outdoor
use dome-type monitoring camera.
For the latest information about the supported cameras, refer to our support website
(https://security.panasonic.com/training_support/support/info/ <Control No.: C0501>).
Specifications
Ambient operating temperature: –30 °C to +50 °C {–22 °F to +122 °F}
Mass: Approx. 20 g{0.04 lbs}
Dimensions: Diameter: 71.0 mm {2-25/32 inches}
Height: 37.5 mm {1-15/32 inches}
Diameter of the dome: 30.5 mm {1-3/16 inches}
Precautions
■ Refer installation work to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire, electric
shock, injury, or damage to the product.
Be sure to consult the dealer.
Standard accessories
Operating instructions (this document)....................................................................................... 1 pc.
Installation
Read the following descriptions together with the Installation Guide of the camera.
Note:
• When a smoke type dome cover is used, the IR LED irradiation distance and the illuminance
level are lower than for a standard clear type dome cover.
Check the settings after attaching the enclosure.
Step1
Loosen enclosure fixing screws (3 places),
and remove the enclosure from the camera.
<Outdoor camera>
Loosen the screws using the bit (camera accessory).
<Indoor camera>
Loosen the screws using a Phillips screwdriver.
* The right illustrations are examples of outdoor use
camera.
Step2
Remove the dome cover.
q Remove the fixing screws (3 pcs.) that secure the dome cover anchor bracket to the enclosure.
w
Remove the dome cover anchor bracket , the dome cover and rubber ring (outdoor camera only).
Note:
• These fixing screws
(3 pcs.)
, the dome cover anchor bracket and rubber ring (outdoor camera
only) will be used again in step3.
Bit (camera accessory) Enclosure
Enclosure fixing
screw (3 places)
<Outdoor camera> <Indoor camera>
Dome cover
anchor bracket
Dome cover
Fixing screw
(3 pcs.)
Enclosure
Rubber ring
Dust guard
sponge
Step3
Replace the dome cover.
q Remove the cover film from the outside of the dome cover (this product). Keep the removed
cover film for following step. (Take care not to damage the outside or inside of this product.)
w Attach the rubber ring to the enclosure. (Outdoor camera only)
e Attach this product to the enclosure.
r Using the fixing screws (3 pcs.) that were removed in step2, secure the dome cover anchor
bracket to the enclosure. (Recommended tightening torque: 0.40 N·m {0.30 lbf·ft})
t Attach the cover film removed in qto the outside surface of this product.
Note:
• When attaching, make sure that the rubber ring is properly set in the groove of the enclosure.
(Outdoor camera only)
• Do not remove the dust guard sponge adhered to the dome cover anchor bracket.
(Indoor camera only)
Step4
Attach the enclosure to the camera.
Tighten the enclosure fixing screws (3 places) using the bit (camera accessory) or Phillips screw-
driver.
Recommended tightening torque: 0.70 N·m {0.52 lbf·ft}
Refer to the Installation Guide of the camera for more information about installing the camera.
<Outdoor camera> <Indoor camera>
Dome cover
anchor bracket
Dome cover
Fixing screw
(3 pcs.)
Enclosure
Rubber ring
Dust guard
sponge
Otros manuales de Accesorios para cámaras de Panasonic
Panasonic
Panasonic BQ-BS2E/2E Manual de usuario
Panasonic
Panasonic WVQ169 - CCTV CEILING MOUNT BRACKET Manual de usuario
Panasonic
Panasonic DMW-DCC9 Manual de usuario
Panasonic
Panasonic Varicam AU-VCVF1G Manual de usuario
Panasonic
Panasonic H-FS1442AE Manual de usuario
Panasonic
Panasonic WV-7150D Manual de usuario
Panasonic
Panasonic WVPS104C - CAMERA DRIVE UNIT Manual de usuario
Panasonic
Panasonic WV-Q117 Manual de usuario
Panasonic
Panasonic WV-Q157 Manual de usuario
Panasonic
Panasonic LC-XC1228AP Manual de usuario
Panasonic
Panasonic DMW-HGR2 Manual de usuario
Panasonic
Panasonic AJ-RC905EN Manual de usuario
Panasonic
Panasonic WVPS154 - CAMERA DRIVE UNIT Manual de usuario
Panasonic
Panasonic CGR18650CG Manual de usuario
Panasonic
Panasonic DMW-MCTZ40 Manual de usuario
Panasonic
Panasonic WV7260 - CCTV ACCESSORIES Manual de usuario
Panasonic
Panasonic AW-AD700BS Manual de usuario
Panasonic
Panasonic WV-CW7S Manual de usuario
Panasonic
Panasonic WVRM70 - ACCESSORY Manual de usuario
Panasonic
Panasonic AS09A51 Manual de instrucciones
