Panasonic DMP-BD60 - Blu-Ray Disc Player Manual de usuario

Otros manuales para DMP-BD60 - Blu-Ray Disc Player

1

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Reproductor de Blu-ray de Panasonic

Panasonic

Panasonic DMP-BDT383 Especificaciones técnicas

Panasonic

Panasonic UltraHD DP-UB159 Manual de usuario

Panasonic

Panasonic DMPBD79 Manual de usuario

Panasonic

Panasonic DMP-BD90 Instrucciones de instalación y servicio

Panasonic

Panasonic DMP-B15K Manual de usuario

Panasonic

Panasonic DMP-UB900 Manual de usuario

Panasonic

Panasonic DMP-BDT330 Manual de usuario

Panasonic

Panasonic DMP-UB900 Manual de usuario

Panasonic

Panasonic DMP-DSB100 Manual de usuario

Panasonic

Panasonic DMP-UB400EBK Manual de usuario

Panasonic

Panasonic DMP-BBT01 Manual de usuario

Panasonic

Panasonic DP-UB820 Manual de usuario

Panasonic

Panasonic DMR-UBS90 Manual de usuario

Panasonic

Panasonic UltraHD DP-UB150 Manual de usuario

Panasonic

Panasonic DMPB100 - PORTABLE BLU-RAY DISC PLAYER Manual de usuario

Panasonic

Panasonic DMP-BDT320 Manual de usuario

Panasonic

Panasonic Diga DMR-BS750EB Manual de usuario

Panasonic

Panasonic DMR-BCT940 Manual de usuario

Panasonic

Panasonic DMR-BWT720EB Manual de usuario

Panasonic

Panasonic DMP-BBT01 Especificaciones técnicas

Panasonic

Panasonic DMP-BDT110PX Manual de usuario

Panasonic

Panasonic DP-UB9000 Especificaciones técnicas

Panasonic

Panasonic DMR-UBT1 Manual de usuario

Panasonic

Panasonic DMP-BDT370 Especificaciones técnicas

Manuales populares de Reproductor de Blu-ray de otras marcas

Samsung

Samsung BD-F5900 Manual de usuario

Philips

Philips BDP3380K Manual de usuario

Samsung

Samsung BD-P4600 Manual de usuario

Sharp

Sharp BD-HP17U - AQUOS 1080p Blu-ray DiscTM Player Manual de usuario

Pioneer

Pioneer BDP-140 Manual de instalación y operación

Samsung

Samsung BD-D8200A Manual de usuario

LG

LG HLX50W Manual de usuario

Sony

Sony BDP-S300 - Blu-Ray Disc Player Manual de usuario

Marantz

Marantz UD9004 Manual de usuario

LG

LG BD611 Manual de usuario

LG

LG BD611 Manual de usuario

Marantz

Marantz BD7004 Guía de inicio rápido

Kogan

Kogan KABRP3DWFIA Manual de usuario

Toshiba

Toshiba BDX2700 Manual de usuario

Samsung

Samsung BD-E5400 Manual de usuario

Samsung

Samsung BD-F5100 Manual de usuario

Philips

Philips BDP7100 Manual de usuario

LG

LG UBK80.DUSALLK Manual de usuario

Panasonic DMP-BD60/BD80

Region switching guide

With the mod. chip fitted the player will automatically play DVD's from all regions (1-6),

but for Blu-ray disc playback the region must be manually selected.

Blu-ray Region switching is done using the player's original remote control while the

player is in standby mode, by pressing the following buttons:

'1' : Select Blu-ray region 'A'

'2' : Select Blu-ray region 'B'

'3' : Select Blu-ray region 'C'

When the player is powered up out of standby mode the new Blu-ray region will be

active. The selected Blu-ray region will remain active until the player is disconnected

from mains power or a new region is selected while the player is in standby mode.

Note that the player must fully enter standby mode to allow the mod. chip to change the

Blu-ray region, therefore the player's "Quick Start" mode (which keeps the player fully

powered up even in standby mode) must be disabled when changing Blu-ray regions.

Blu-ray region switching is possible with any remote channel setting, 1, 2 or 3.

Panasonic DMP-BD60/BD80

Mod. chip fitting guide

Warning: Modifying your player will invalidate any existing warranty. The mod. chip is

difficult to fit, requiring soldering of small surface mount components and therefore

fitting should only be carried out by those with the appropriate experience. A low power

(15-25W) soldering iron with very small tip is essential. If you don't have the required

tools and experience do not attempt to fit the mod. chip as it's very likely that you will

damage your player.

Please read this guide fully before starting to fit the mod. chip.

Before opening the player ensure that all cables are completely disconnected from it.

Double check that the mains cable is disconnected.

To open the player remove the 7 fixing screws, 2 from left side, 2 from right side and 3

from the rear. The top cover can now be lifted off.

The main board is on the right side and the image below shows the areas where the mod.

chip will be connected to it.

6 pins on the mod. chip are used in total, #1, #2, #3, #4 and #8 connect to the main board

and #5 to the rear of the front panel.

Mod. chip pin #1 should be connected to the 2nd bottom of the 6 long solder pads, as

shown.

Mod. chip pins #2, #3, #4 and #8 should be connected to the small 8 pin chip as shown.

For access to the connection point for mod. chip pin #5 the front panel of the player has to

be removed. To remove the front panel, look for the 7 plastic clips holding it in place, 1

left, 1 right, 2 top and 3 bottom. Carefully unclip them from one side, then the other and

the front panel should pull free.

With the front panel removed you can now see the area where mod. chip pin #5 will be

connected.

Connect pin #5 to the point on the front panel PCB shown below.

Bring the wire for mod. chip pin #5 in under the metal plate at the front of the player,

ensuring that it doesn't block the connector shown at the left side.

When re-fitting the front panel check that all 7 plastic clips are fully in place, otherwise

the electrical connectors may not contact correctly.

Pins #1 and #5 should be connected with wires, however for the pins that connect to the 8

pin chip on the main board (#2, #3, #4 and #8) it's possible to either connect them with

wires or to "piggy-back" the mod. chip on top of the 8 pin chip on the board. If you

connect all the pins with wires then the mod. chip must be wrapped in insulation tape and

secured in a safe position, so the "piggy-back" option is quicker and only requires 2 wires

for pins #1 and #5.

To "piggy-back" the mod. chip, bend pins #2, #3, #4 and #8 inwards against the body of

the mod. chip and then #3, #4 and #8 as shown below. Trim pins #1 and #5 and

trim/remove the unused pins #6 and #7.

Bend the pins into position and then hold it against the chip on the board to make sure

they are lined up correctly. Once all the pins are lined up solder pin #8 first, then you can

carefully position the mod. chip by rotating it slightly and solder pins #2, #3 and #4.

It should then look similar to the image below.

And the full install should look like this, with the wires for pins #1 and #5 in place.

If you're not confident with the "piggy-back" fitting method just use wires to connect all 6

pins of the mod. chip.