Electric Planer
7
temperatures from 0 to +40 ° C and relative
humidity up to 80%. The presence of acid va-
pors, alkalis and other aggressive impurities
in the air is not allowed.
Products can be transported by any type of
closed transport in the manufacturer’s pack-
aging or without it, while preserving the prod-
uct from mechanical damage, atmospheric
precipitation.
Dispose of waste
Damaged power tools, batteries, ac-
cessories and waste packaging mate-
rials must be recycled and reused in
an environmentally friendly manner.
Do not throw power tools and accumulators /
batteries into general household waste!
Product serial number interpreta-
tion
The fi rst and second digits of the product seri-
al number from left to right
Year of production, the third and fourth digits
indicate the month of production, the fi fth and
sixth digits indicate the production day.
TERMS OF WARRANTY SERVICE
1. This Warranty Certifi cate is the only docu-
ment that confi rms your right to free warranty
service. Without presenting this certifi cate, no
claims are accepted. In case of loss or dam-
age, the warranty certifi cate is not restored.
2. The warranty period for the electric ma-
chine is 12 months from the date of sale,
during the warranty period the service depart-
ment eliminates manufacturing defects and
replaces parts that have failed due to the fault
of the manufacturer free of charge. In the war-
ranty repair, an equivalent operable product
is not provided. Replaceable parts become
property of service providers.
P.I.T is not liable for any damage that may be
caused by operation of the electric machine.
3. Only clean tool accompanied with the
following duly executed documents: this War-
ranty Certifi cate, Warranty Card, with all fi elds
fi lled out, bearing the stamp of the trade orga-
nization and the signature of the buyer, shall
be accepted for warranty repair.
4. Warranty repair is not performed in the fol-
lowing cases:
- in the absence of a Warranty Certifi cate and
a Warranty Card or their incorrect execution;
- with failure of both a rotor and a stator of the
electric engine, charring or melting of primary
winding of the welding machine transformer,
charging or starting-charging device, with in-
ternal parts melting, burn down of electronic
circuit boards;
- if a Warranty Certifi cate or a Warranty Card
does not correspond to this electric machine
or to the form established by the supplier;
- upon expiration of the warranty period;
- at attempts of opening or repair of the elec-
tric machine outside the warranty workshop;
making constructive changes and lubrication
of the tool during the warranty period, as ev-
idenced, for example, by the creases on the
spline parts of the fasteners of non-rotational
parts.
- when using electric tools for production or
other purposes connected with making a prof-
it, as well as in case of malfunctions related
to instability of the power network parameters
exceeding the norms established by GOST;
- in the events of improper operation (use the
electric machine for other than intended pur-
poses, attachments to the electric machine of
attachments, accessories, etc. not provided
by the manufacturer);
- with mechanical damage to the case, pow-
er cord and in case of damages caused by
aggressive agents and high and low tempera-
tures, ingress of foreign objects in the ven-
tilation grids of the electric machine, as well
as in case of damage resulting from improper
storage (corrosion of metal parts);
- natural wear and tear on the parts of the
electric machine, as a result of long-term op-
eration (determined on the basis of the signs
of full or partial depletion of the specified
mean life, great contamination, presence of
rust outside and inside the electric machine,
waste lubricant in the gearbox);
- use of the tool the purposes for other than
specifi ed in the operating instructions.
- mechanical damages to the tool;
- in the event of damages due to non-obser-
vance of the operating conditions specifi ed in
the instruction (see chapter “Safety Precau-
tions” of the Manual).
- damage to the product due to non-obser-
vance of the rules of storage and transporta-
tion.
- if the instrument is heavily contaminated in-
ternally.
Preventive maintenance of electric machines
(cleaning, washing, lubrication, replacement
