OWC Mercury Elite-AL Pro Manual de usuario
Owner’s Manual
Assembly Guide
OWC Mercury Elite-AL Pro ‘Quad Interface’
External Storage Enclosure for
3.5”Serial ATA Hard Drive
Includes FireWire 400, FireWire 800, USB 2.0 and eSATA Ports
Thank you for purchasing your new Other
World Computing Mercury Elite-AL Pro ‘Quad
Interface’ hard drive enclosure. Please follow
these steps to install your hard drive mecha-
nism into the case.
1. Unpack your Mercury Elite-AL drive and it’s contents.
2. Take the drive enclosure and look at it’s port layout. Everything
is clearly labeled here. Note the 4 screws at the corners of the
drive, you will need to remove these in the next step.
3. Remove the 4 screws from the back of the hard drive enclosure
using the included Torx T-10 screwdriver. The back cover will not
fully come o of the enclosure, it’s attached by wires going to the
power switch.
4. Once the top cover is removed, set it aside, to expose the inter-
nal bay as shown.
5. Take your 3.5”SATA hard drive and set it into the drive enclo-
sure. You need to attach the power cable (the red, black, and
yellow cable) to the SATA hard drive, and also connect the SATA
cable to the hard drive. Make certain that you do not pinch the
red and black LED cable on the left side in this picture - make
sure it’s free from being caught underneath the drive.
6. Once you have the cables attached, lower the hard drive down
into the enclosure, until it is at on the mounting rails. Make sure
that the cables you just attached to the drive lay down at, to aid
in the last step when you slide on the top cover.
7. Look at the side of the drive enclosure. You will see the 2 holes
shown here, on each side of the enclosure. Fasten the drive into
the enclosure with the included Phillips screws here.
8. Closeup showing 2 screws installed on the left side. Repeat for
the right side. Make very certain that the screws are tight.
9. Set the top cover back onto the drive enclosure, sliding the
cover onto the enclosure in it’s enclosed rail. Once the top cover
is fully closed, replace the 4 Torx T-10 screws from the back cover,
and the drive is ready to hook up to your computer for format-
ting. Attach the power cable, the interface cable of your choice,
and power the drive on.
System Setup:
Your Mercury Elite-AL Pro drive is simple to hook up to your
computer. Choose whichever interface you prefer to use, for best
performance use either the FireWire 800 ports or the eSATA pors.
Simply insert the interface cable (all types included with the
enclosure) to your computer.
Here are a few tips to get the most out of your new external
storage and expansion device:
• Do not place anything in front of your Mercury Elite-AL Pro that
would block airow.
• Treat your Mercury Elite-AL Pro just like you treat your
computer- keep it dry, cool, and out of direct sunlight
• Always check any peripheral cable that you are going to use
with your Mercury Elite-AL Pro enclosure for damage before
hooking them up.
Formatting for use with Mac OS X:
Once formatted, you’re all set! Your new Mercury Elite-AL Pro
is ready to use! Connect any USB or FireWire peripherals to
the hubs and enjoy!
Upon initial startup of your new Mercury Elite-AL Pro drive, you
will be greeted with the following dialog box:
Click on the “initialize” button to open Disk Utility to proceed
with initializing the new hard drive.
Click on the new hard drive with no volumes attached to it to
initialize the new drive mechanism. For full instructions, please
visit this web address:
http://eshop.macsales.com/tech_center/index.cfm?page=/
manuals/mercuryrewire/format/osx/osx1.html
® Copyright 2006 by Other World Computing All Rights Reserved
The information contained within is believed to be accurate and reliable.
Other World Computing assumes no responsibility for any errors contained
within. Other World Computing reserves the right to make changes in the
specications and/or design of this product without prior notice. The pho-
tographs contained within may dier from the product that you receive and
are there for illustration purposes only. Other World Computing assumes no
responsibility for any dierences between the product mentioned in this
manual and the product you may receive.
Revision 1 July 11, 2006 JD
OWCMANME924AL1
Otros manuales para Mercury Elite-AL Pro
7
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Recinto de OWC
OWC
OWC Mercury Elite Pro Dual mini Guía
OWC
OWC ENVOY EXPRESS Manual de usuario
OWC
OWC Mercury Elite-AL Pro Manual de usuario
OWC
OWC EXPRESS 4M2 Guía
OWC
OWC U.2 NVMe Interchange System Guía
OWC
OWC Mercury On-The-Go Pro Series Manual de usuario
OWC
OWC Mercury Elite Pro Dual Guía
OWC
OWC Envoy Pro Manual de usuario
OWC
OWC ThunderBay 4 Guía
OWC
OWC Mercury Elite Pro Dual Bay Manual de usuario
OWC
OWC Mercury Elite Pro Dual Guía
OWC
OWC NASPerform Manual de usuario
OWC
OWC data doubler Manual de usuario
OWC
OWC Envoy Pro Manual de usuario
OWC
OWC Mercury Elite-AL Pro Manual de usuario
OWC
OWC OWCMANVLS2ASY Manual de usuario
OWC
OWC Mercury On-The-Go Pro Manual de usuario
OWC
OWC Mercury Elite RAID Manual de usuario
OWC
OWC Mercury On-The-Go Manual de usuario
OWC
OWC Mercury Elite Pro Dual Guía
