Overland Storage SnapServer 2U Appliance Guía

*10400578003*

SnapServer 2U Appliance / SnapScale X2®Node

Spare Chassis Replacement Instructions

This document describes how to remove and replace a

SnapServer 2U appliance or SnapScale X2 node chassis from

Overland Storage.

WARNING: To reduce the risk of electric shock or damage to

equipment, always remove any power cords while working

with the unit.

WARNUNG: Um das Risiko eines elektrischen Schlags oder

Schäden am Gerät zu vermeiden, ziehen Sie stets den

Netzstecker, bevor Sie an der Einheit arbeiten.

AVERTISSEMENT: Pour réduire le risque de choc électrique

ou endommagement de l'équipement, retirez toujours les

cordons électriques en travaillant avec l'appareil.

CAUTION: While working with the unit, observe standard

Electrostatic Discharge (ESD) precautions to prevent damage

to micro-circuitry or static-sensitive devices.

Prepare the Unit

Remove Node from Cluster (SnapScale)

When replacing a SnapScale node’s chassis, you must first

remove the node from the cluster:

1. At the Web Management Interface, go to

Storage > Nodes

and click the node name to view the

Node Properties

page.

2. Click

Remove Node from SnapScale

and confirm.

3. If the node is running, wait for the node to reboot as an

Uninitialized node.

Power Off and Disconnect

If the unit is still running, power it down cleanly:

1. Power off the server/cluster:

•SnapServer: Use the Web Management Interface to

shut down the server (

Maintenance > Reboot and

Shutdown > Shutdown

•SnapScale: After removing the node from the cluster,

press the Power button on its left flange to shut it

down.

2. When all the LEDs are off, disconnect the power cords.

3. Disconnect the remaining cables from the unit, noting

their locations.

Power Button X2 Node

XSR 120Power Sockets Cable Ports

Spare Chassis Replacement Instructions

Remove the Front Bezel

1. Carefully take hold of the front bezel and pull it straight

out from the appliance until the magnets release.

2. Set the bezel aside on a secure surface.

Remove the Drives

IMPORTANT: Overland recommends that you remove the disk

drives to reduce the unit’s weight prior to removal.

Remove all the drive carriers. For SnapScale, note from which

bay they were removed. Blank carriers can remain in the bays.

NOTE: Do not remove the disk drives from their carriers. Doing so

voids the drive warranty.

1. Press the release button on the right side of the carrier.

2. Using the built-in handle, pull the carrier out.

3. Number the carrier and set it on a secure surface.

4. Repeat Steps 1–3 for all the remaining drive carriers.

Remove Unit from Rack

WARNING: It is recommended that a mechanical lifter (or at

least two people) be used during rack installation or removal

to prevent injury.

WARNUNG: Um Verletzungen zu vermeiden, empfehlen wir

zur Rack-Installation oder -Deinstallation die Nutzung einer

mechanischen Hebehilfe (oder mindestens zwei Personen).

AVERTISSEMENT: Pour éviter toute blessure il est

recommande qu'un monte-charge (ou deux personnes au

moins) soit utilisé lors de l'installation ou de l'enlèvement du

support.

1. Remove and retain the four screws securing the unit to

the rack.

2. With a lifter positioned in front of the array, release the

rail locks and slide the chassis out onto the lifter.

3. Move the chassis onto a secure surface.

4. Unpack the new chassis and place it next to the old one.

Transfer Components

Move Inner Sliding Rails

1. Remove and retain the screws securing one of the rails to

the old chassis.

2. Position the rail on the new chassis, and secure it with

the retained screws.

3. Repeat Steps 1–2 for the other rail assembly.

X2 Node

Press

Old Chassis New Chassis

Secure Surface

Spare Chassis Replacement Instructions

Remove Top Panels

1. On the new chassis, remove and retain the two screws

located at the front edge of the panel.

2. Loosen the two captive screws securing the panel rear.

3. Slide the panel toward the rear about one-half inch

(1.25cm), lift it off, and set aside.

4. Repeat Steps 1–3 to remove the top rear panel from the

old chassis.

Move Power Supplies

1. At the old chassis, press the top release latch and pull

the power supply out using the black handle.

2. At the new chassis, slide the power supply into a bay

until it locks (clicks).

3. Repeat Steps 1–2 for the remaining power supply.

Move DIMMs

All installed DIMMs need to be moved to the new chassis.

1. In the old chassis, remove a DIMM by pressing the latches

on each end and lifting the DIMM out.

2. In the same slot of the new chassis, position the DIMM by

lining up the DIMM notch with the guide in the slot.

3. Firmly press the DIMM down until the latches secure the

DIMM in place.

4. Repeat Steps 1–3 for each remaining DIMM.

Move PCIe Cards

Any installed PCIe cards need to be moved to the new chassis:

1. In the old chassis, remove and retain a PCIe card’s slot

cover screw.

2. In the new chassis, remove and retain the rear slot cover

and screw that matches the old chassis PCIe card slot.

3. Grasp the PCIe card and carefully pull it straight up and

out of the old chassis slot.

4. Insert the PCIe card in the same slot in the new chassis

and secure it with the retained slot cover screw.

5. Install the slot cover in the old chassis where the PCIe

card was located using the retained screw.

6. Repeat Steps 1–5 for any other PCIe cards.

Rear

Front Screws

Captive

Screws

Press

Screw

Spare Chassis Replacement Instructions

Reinstall Top Panels

1. At the new chassis, position the top panel with no more

than one-half inch (1.25cm) extending out over the rear

of the unit.

2. Slide the panel forward until it is fully seated.

3. Using the two captive screws, secure the panel rear.

4. Using the two retained screws, secure the panel front.

5. Repeat Steps 1–4 for the old chassis.

Reassemble the Unit

Install New Chassis to Rack

1. Slide out the middle rails from the rack.

2. Using the mechanical lifter, position the chassis in front

of the rack.

3. Insert the inner rails into the middle rails and slide the

unit into the rack.

4. Using the four retained screws, secure the unit.

Reinstall Drives

1. Position a drive assembly in front of its empty bay.

For SnapScale, they must be returned to the bay they

were removed from. Refer to the number on the assembly.

2. Slide the assembly in until the latch clicks, securing it.

3. Repeat Steps 1–2 for all remaining drive carriers.

IMPORTANT: To maintain proper airflow and cooling, a drive

assembly or a blank carrier must be installed in every bay. No

empty bays are allowed.

Reattach Cables and Power Cords

1. Reattach all cables to the same connections as before.

2. Attach the power cords.

3. At the front of the unit, press the power switch for less

than a second to power the unit ON.

Rear

Front Screws

Captive

Screws

XSR 120Power Sockets Cable Ports

http://support.overlandstorage.com

You can get additional technical support on the Internet at the Overland Storage Support web page, or by contacting Overland Storage using

the information found on the Contact Us page on our web site.

Spare Chassis Replacement Instructions

Important – Read This Before Continuing

During the power-on sequence, the Status LED flashes an

alternating green and amber pattern.

•If the OS versions are the same on both the chassis and

drives, the appliance boots normally.

•If the OS on the new chassis is different from the version

on the disk drives, the appliance goes through a special

initialization and synchronization process that can take

up to 10 minutes to complete with the Status LED

flashing alternating green and amber.

CAUTION: Under no circumstances should power be removed

while the system is in this state! Doing so may render the

appliance inoperable.

Once initialization is complete, the system automatically

reboots and the Status LED displays a solid green color.

Reattach the Bezel

1. Position the bezel with the tabs aligned inside the top

and bottom edges of the chassis.

2. Move bezel toward the unit until the magnets connect.

3. Verify that the bezel is aligned properly, all the LEDs are

visible, and the Power panel is centered in the left flange.

Add Node to Cluster

NOTE: If the node was not running before removing it from the

cluster, contact Overland Technical Support at http://

docs.overlandstorage.com/support for help adding it.

1. Log onto the Web Management Interface and go to

Storage > Nodes

(by clicking the

Nodes

quick link).

2. Click

Add Nodes

and follow the wizard to add the

refreshed node back to the cluster.

Return Replaced Parts to Overland

1. Place the replaced chassis in the anti-static bag and put

it in the replacement part’s box.

2. Use the existing packing materials to secure it.

3. Use an RMA to return the part to Overland Storage.

For return shipping details and RMA number, go to:

http://docs.overlandstorage.com/return-instructions

Status LED XSR 120

Magnets Tabs

Otros manuales para SnapServer 2U Appliance

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Servidor de Overland Storage

Overland Storage

Overland Storage SnapServer Manual de servicio

Overland Storage

Overland Storage SnapServer DX1 Manual de usuario

Overland Storage

Overland Storage SnapServer Expansion E2000 Manual de usuario

Overland Storage

Overland Storage SnapServer DX2 Guía

Overland Storage

Overland Storage SnapServer 110 Manual de usuario

Overland Storage

Overland Storage snap server 410 Manual de usuario

Overland Storage

Overland Storage Snapshot SnapSAN Manual de usuario

Overland Storage

Overland Storage ARCvault Series Manual de usuario

Overland Storage

Overland Storage SnapServer SAN S2000 Manual de usuario

Overland Storage

Overland Storage SnapServer 510 Manual de usuario

Overland Storage

Overland Storage Snap Server 18000 Manual de usuario

Overland Storage

Overland Storage SnapServer Manual de servicio

Overland Storage

Overland Storage SnapServer N2000 Manual de usuario

Overland Storage

Overland Storage SnapServerXSR 40 Manual de usuario

Overland Storage

Overland Storage SnapServer XSR 120 Manual de usuario

Overland Storage

Overland Storage SnapServer DX1 Manual de usuario

Overland Storage

Overland Storage SnapServer XSR 120 Manual de usuario

Overland Storage

Overland Storage ARCvault Series Manual de usuario

Overland Storage

Overland Storage Snap Server 18000 Manual de instrucciones

Overland Storage

Overland Storage SnapServer XSD 40 Manual de usuario

Overland Storage

Overland Storage Snap Server 14000 Manual de usuario

Overland Storage

Overland Storage DXSeries Manual de usuario

Overland Storage

Overland Storage SnapScale Manual de servicio

Overland Storage

Overland Storage SnapServer 210 Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario