OTC Wireless WiJET.Video Manual de usuario

WiJET.Video

Wireless Projector and Monitor Adapter

With Motion Video

Technical Manual

***** DRAFT *****

www.otcwireless.com

WiJET.Video Technical Manual Page ii of 29

OTC Wireless, Inc.

WiJET.Video

Technical Manual

Information in this document is subject to change without notice. Complying with all

applicable copyright laws is the responsibility of the user. No part of this document may

be reproduced or transmitted in any form or by any means, electronic or mechanical,

for any purpose, without the express written permission of the seller. If, however, your

only means of access is electronic, permission to print one copy is hereby granted.

The seller provides this documentation without warranty, term, or condition of any kind.

The seller may make improvements or changes in the product(s) and/or the program(s)

described in this documentation at any time.

Other product and company names herein may be trademarks of their respective

owners.

Rev 1.01 Draft

WiJET.Video Technical Manual Page iii of 29

Table of Contents

Chapter 1: INTRODUCTION......................................................................................... 1

Key Features..................................................................................................................2

Specifications .................................................................................................................2

Chapter 2: WiJET.Video SYSTEM INSTALLATION.................................................. 3

2.1 Safety Statements ..................................................................................................3

2.2 Hardware Installation ..............................................................................................3

2.2.1 Power................................................................................................................3

2.2.2 VGA Connection.................................................................................................3

2.2.3 Video Output Signal Connections ........................................................................3

2.2.4 Status LED’s ......................................................................................................3

2.2.5 Reset to Factory Default......................................................................................3

2.3 User Software Installation........................................................................................4

2.3.1 System Requirements for User Software..............................................................4

2.4 System Requirements for Web-served Administration Application..............................4

Chapter 3: USING WiJET.Video.................................................................................. 6

3.1 Using the WiJET.Video in a Meeting........................................................................6

3.2 Starting the WiJET.Video ........................................................................................7

3.3 Configuring Computer to Control WiJET.Video .........................................................8

3.4 Starting Presentation Session Manager....................................................................8

3.5 Configuring the Wireless Adapter to Connect with WiJET.Video...............................10

3.5.1 Configure the Wireless Network Adapter ............................................................10

3.5.2 Configure the Wireless Adapter for Windows XP .................................................10

3.6 Start or Resume Your Presentation Session...........................................................13

3.6.1 “WiJET.Video is Occupied” Message .................................................................14

3.7 Play Video............................................................................................................14

3.8 Launch PowerPoint...............................................................................................14

3.9 Release Your Presentation Session.......................................................................14

3.10 Exit the Presentation Session Manager..................................................................14

Chapter 4: WEB-SERVED ADMINISTRATION APPLICATION............................... 15

4.1 Introduction to the Web-served Administration Application.......................................15

4.2 Accessing the Web-Served Administration Application ............................................15

4.3 Configuring the WiJET.Video Using Administration Manager...................................16

4.3.1 WiJET.Video Firmware Version .........................................................................17

4.3.2 Configuration....................................................................................................18

4.3.3 Administration ..................................................................................................19

4.3.4 Firmware and Banner Page Upload ...................................................................20

Chapter 5: TROUBLESHOOTING ............................................................................. 21

5.1 Unable to Connect or Establish a Session with Unit ................................................21

5.2 The Presentation screen appears frozen during a presentation................................21

5.3 The WiJET.Video Session is Interrupted During a Presentation ...............................22

5.4 Radio Interference................................................................................................22

5.5 Technical Support.................................................................................................23

Appendix A: LIMITED WARRANTY............................................................................... 24

WiJET.Video Hardware.................................................................................................24

Appendix B: REGULATORY COMPLIANCE................................................................. 25

FCC Part 15 Declaration of Conformity (DoC).................................................................25

FCC ID: TBD................................................................................................................25

FCC Rules and Regulations -Part 15.............................................................................25

European Community (EC) Directives Conformity and Restrictions ..................................26

Industry Canada Compliance Information Statement .......................................................26

WiJET.Video Technical Manual Page 1of 29

Chapter 1: INTRODUCTION

The OTC Wireless Projector and Monitor Adapter with Motion Video, WiJET.Video is an

IEEE 802.11g compliant product designed specifically for wirelessly connecting

projectors and monitors to computers. It connects to the existing VGA connector of the

projector/monitor and offers 802.11g connectivity up to 54 Mbps.

The advantages of the WiJET.Video become obvious in any conference room where

the ideal location of the projector or display screen makes it difficult for a laptop or

desktop to connect to it while allowing the speaker to maintain audience interest. All

too frequently, projectors placed in the middle of the room force the speaker to present

from the middle of the room, because of the VGA cable that exists between the

projector and the presenter’s laptop.

The WiJET.Video solves this problem by allowing any laptop or desktop with an

802.11g Wi-Fi adapter to give the presentation from anywhere in the conference room

that the presenter desires. Wherever the presenter feels would garner the most

amount of interest from the audience. Truly freedom from wires allows for more

flexibility in meetings.

Another application of the WiJET.Video is in a situation where multiple presenters must

give presentations in rapid succession. The WiJET.Video allows for fast handover of

the projector or monitor without the hassle of removing and reattaching the VGA cable.

Using the easy-to-use Presentation Session Manager, the presenters can effortlessly

connect to the WiJET.Video, give a presentation, and disconnect from the WiJET.Video

to allow another user to connect to it without touching a single cable.

A third application that showcases the advantages of the WiJET.Video is where there

are multiple conference rooms with multiple projectors. A WiJET.Video in every

conference room will substantially save setup time when the presenter comes into the

room. The presenter only simply selects the WiJET.Video number displayed on the

projector/monitor screen and he is instantly connected to the projector and able to start

his presentation. This removes a lot of setup time associated with presenters moving

from room to room to give their presentations, ultimately saving IT costs.

In summary, the WiJET.Video is a tool that will change how people come to view

conferences and meeting rooms. Instead of a static meeting place, the conference

rooms can now become a dynamic meeting place where new thoughts and ideas are

exchanged and created.

WiJET.Video Technical Manual Page 2of 29

OTC WiJET.Video Wireless Projector/Monitor Adapter

Key Features

qInteroperable with any PC/Laptop equipped with Windows OS and an industry standard IEEE

802.11g-compliant wireless interface cards

qSimple user interface with the supplied Windows-based client software

qPlug & Play—

oOperating as AP for easy wireless connection from any PC

oAutomatically scanning for the clearest channel and avoiding duplicate SSID

oNo need to change IP address settings of the wireless card in a user’s PC

qMaximum 54 Mbps data rate with automatic fall back to maintain best link connection

qDirect access to video buffer to allow fast real-time updates of the projected images-no long and

embarrassing pauses or broken images

qUp to1024x768 resolution for optimized speed/resolution tradeoff

qAutomatic re-connect of sessions/ wireless link

qUser customizable WiJET.Video-ready banner image to allow the display of information such as

meeting agenda, conference logo, etc. before and between presentations

qWeb browser based administration application for upgrading firmware and setting encryption

keys

qStandard VGA connector to allow the use with any presentation projector

qPlaying MPEG video to connected TV and VGA-monitor of contents on the PC

qPlaying embedded video objects in PowerPoint presentation

Specifications

Model OTC Wireless Projector and Monitor Adapter with Motion Video

Standard 802.11g

Projector/Monitor Interface Standard 15-pin VGA connector; Component, Composite & S-Video

Display resolution & color Automatically set to user’s display resolution up to XGA (1024x768)

Automatically set to user’s color depth up to 16-bit True-Color

Client Software supplied Client software run on Windows 98/ NT4/ ME/2000/ XP

Web-served Administration application to allow user to upload banner

page, set WEP, set channel and upload firmware upgrades

Frequency 2.4GHz –2.483GHz

RF Channels 11 channels (US, Canada), 13 channels (Europe), 13 channels (Japan)

Transmission power 14dBm at antenna input typical

Receiver sensitivity -80dBm @1e-5 BER typical

Antenna Support antenna diversity with one externally connected (RSMA

connector) Dipole antennae with ~5dBi gain and an internal dipole

antennae with ~0 dBi gain

Data Rate 54 Mbps maximum with multiple user selectable fall back data rates.

Modulation OFDM, Direct Sequence Spread Spectrum

Link Distance ~1200 ft in open space; 300 ft typical indoor environment

Network Types AP mode for dedicated presentation link and other traffic as desired.

Network Security 64bit or 128-bit WEP

DC Voltage 5V

Current consumption 1.7A (max. reached in transmit-mode)

LED Indicators Power, Wireless Link

Dimensions 4.4”x6.25”x1.5”

Operating Temperature -10°C –+50°C

Operating Humidity 10% to 85% non-condensing

Regulation Compliance FCC, CE

WiJET.Video Technical Manual Page 3of 29

Chapter 2: WiJET.Video SYSTEM INSTALLATION

2.1 Safety Statements

Use only the power adapter provided with this product or the manufacturer's authorized

replacement power supply.

Connect the power adapter to a properly grounded electrical outlet that is near the

product and easily accessible.

Refer service or repairs, other than those described in the user documentation, to a

professional service person.

2.2 Hardware Installation

2.2.1 Power

Power is supplied to the WiJET.Video via a 1.7 amps 5volt DC power adapter.

Warning: use only the power supply adapter provided with this product or the

manufacturer’s authorized replacement power supply.

2.2.2 VGA Connection

This is a standard 15 pin female VGA connector where you will connect the WiJET.Video

to either a monitor or a projector via a straight-thru monitor cable (either purchased

separately or with the one that comes with the projector or monitor).

2.2.3 Video Output Signal Connections

WiJET.Video provides an S-Video connection. Regular S-Video cable can be used to

connect with an S-Video input on a TV or projector. Special cables may be ordered to

connect to composite video or component video inputs.

2.2.4 Status LED’s

There are two status LED’s on the WiJET.Video. From the front of the unit, the LED on

the left is the power indicator while the LED on the right is the link status and video out

indicator. During boot-up, the link status LED will initially remain unlit. When the link

LED blinks red, it means the WiJET-G is ready for connection to a PC. Upon

connection from a computer, the LED will turn solid green. Upon disconnection, the

LED will revert to blinking red again.

2.2.5 Reset to Factory Default

WiJET.Video provides a pin-push button to the side of the unit. Press this button for a

second to reset the WiJET.Video back to the factory default setting. The unit will

reboot.

Normally, this should only be done when you forget the Web password or when the

WEP keys have become incompatible with the wireless card on your PC.

WiJET.Video Technical Manual Page 4of 29

Caution: Please note that resetting the product to its factory default means losing all

configurations and encryption information you may have set through the

web interface!

2.3 User Software Installation

The following details the steps involved in installing the software needed to control the

WiJET.Video.

2.3.1 System Requirements for User Software

To use the WiJET.Video user software, your computer must meet the following

requirements.

•Wi-Fi or IEEE 802.11g enabled computer (either built-in or add-on NIC);

•Windows 98/NT4/ME/2000/XP; and

•Minimum equivalent processing power of Pentium 3 at 750 MHz and 64MB of

RAM.

2.3.1.1 Installation for the WiJET.Video Presentation Session Manager (PSM)

This step is optional and can be skipped for those who simply want to run WiJET.Video

Presentation Session Manager (PSM) without the administration capability. PSM can

be executed on CD-ROM without being “installed” to the local hard drive. To install the

WiJET.Video software on your local hard drive, insert the Installation CD in your

computer’s CD-ROM drive. A Selection window would automatically start and the user

can choose to run the PSM from CD-ROM or to install the PSM onto the local hard

drive. If the program does not automatically start, go to “My Computer” and double

click on the Installation Disc icon. Click on WiJET.Video.exe once you can see the

CD’s contents.

Simply follow the instructions from the installation process to install the PSM software

once the installation program starts running.

2.3.1.2 Installation for the WiJET.Video Administration Manager

To install Administration Manager, explore the WiJET.Video CD in the CD-ROM drive

and enter the admin folder. Click on “setup.exe” in the admin folder and follow the

instructions for installation of Administration Manager. For instructions on using the

Administration Manager, please see Chapter 4: –Using the Web-served Administration

Application.

2.4 System Requirements for Web-served Administration Application

WiJET.Video has a Web-served Administration Application that can be used to

configure the settings of the product. The Web-based Administration Application can be

accessed through WiJET.Video Administration Manager. To use the Web-served

Administration Application, the computer must meet the following requirements:

(1) A Web browser must be installed on the computer. The supported Web browsers

include Internet Explorer 5.0 and above, Netscape 6.0 and above, Mozilla 1.0 or above

and Opera 6.05 or above. JavaScript for the browser must be enabled.

WiJET.Video Technical Manual Page 5of 29

(2) IEEE 802.11g or Wi-Fi enabled computer (either built-in or add-on NIC).

See Chapter 4: for detailed information on how to configure the WiJET.Video

using Web-served application.

WiJET.Video Technical Manual Page 6of 29

Chapter 3: USING WiJET.Video

3.1 Using the WiJET.Video in a Meeting

In addition to the obvious convenience with wireless connection, the most important

benefit of eliminating the VGA cable in using presentation projectors or monitors is to

enable fast handover of the projector or monitor control among multiple meeting

participants. The Presentation Session Manager (PSM) provides a simple user

interface allowing quick rotation of presentation among multiple presenters. The

following simple steps sketch out how a successful Wireless Presentation Meeting

unfolds:

1. Copies of the WiJET.Video installation CD are kept with the product in the

meeting room. The meeting host, before the presentations start, identifies the

meeting participants who do not yet have the Presentation Session Manger

installed on their computers and hands them the installation CDs. The

participants can either run PSM from the CDs or install the PSM onto their

system. The installation is automatic and does not require rebooting the

computer.

2. The meeting host asks all meeting participants to establish a wireless

connection to the product before the meeting starts. Most participants can

accomplish this by clicking just one button. This wireless connection is kept

alive throughout the meeting even if only one presenter can use the projector or

monitor at a given time. Confirming wireless connections before the meeting

starts assures a smooth presentation session.

3. At any given time, by clicking just one button in the PSM, one designated

presenter can start the presentation and exclude other presenters from using

the projector/monitor.

4. At the click of one button in the PSM, the incumbent presenter yields the floor

(the projector/monitor) to another presenter while still maintaining a live wireless

link to the WiJET.Video.

5. At the click of one button in the PSM, a waiting presenter, owing to the already

established wireless link, can instantaneously take over the projector/monitor.

The normal meeting etiquettes have to be followed to determine how the control of the

projector/monitor should be rotated among presenters. The WiJET.Video and its PSM

make the rotation easy and quick and thereby make the meeting dynamic.

WiJET.Video Technical Manual Page 7of 29

3.2 Starting the WiJET.Video

When the product is first turned on, a boot up sequence will follow. After about 30

seconds, the unit will display the following graphic (Figure 3.1) with a few informative

messages.

Figure 3.1 WiJET.Video Banner Page

The messages will be displayed on the top of this image and consist of two lines. The

top line displays the SSID and the channel number of the unit while the second line

reports on the channels currently in use by other 802.11g equipment around the unit.

An example of the messages is given below:

SSID=WiJET.Video0001 Channel=6

RF activities detected on other channels (none).

There are several variations to the message on the second line. The variations and

what they mean are as follows:

RF activities detected on other channels (none).

No other 802.11g/b channels detected in use other than the WiJET.Video at all. Your

connection to the unit should be smooth and error free.

Tabla de contenidos

Otros manuales de Adaptador de OTC Wireless

OTC Wireless

OTC Wireless WiSER2400 Manual de usuario

OTC Wireless

OTC Wireless AVCW-G Manual de usuario

OTC Wireless

OTC Wireless ACR-201 Manual de usuario

OTC Wireless

OTC Wireless WiSER2400 Manual de usuario

OTC Wireless

OTC Wireless WiJET Manual de usuario

OTC Wireless

OTC Wireless WIJET.G 802.11G Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario