OSS OSS-PCIe-HIB38-x4 Manual de usuario

PCIe x4 Gen 3, Switch-based Cable Adapter

OSS-PCIe-HIB38-x4

User Manual

SKU: OSS-PCIe-HIB38-x4

www.onestopsystems.com

One Stop Systems

OSS-PCIe-HIB38-x4 |

Table of Contents

Advisories ............................................................................................................................................................................................................ 4

Safety Instructions ............................................................................................................................................................................................... 5

1Hardware Requirements.................................................................................................................. 7

1.1 Host card Configuration ............................................................................................................................................................................ 7

1.2 Target card Configuration ......................................................................................................................................................................... 7

2Hardware Installation...................................................................................................................... 8

2.1 Tools Required for Installation .................................................................................................................................................................. 8

2.2 Installation-Procedures Overview ............................................................................................................................................................. 8

2.3 Set Dipswitch for each Adapter card......................................................................................................................................................... 9

2.4 Install Host Adapter card........................................................................................................................................................................... 9

2.5 Install Target Adapter card........................................................................................................................................................................ 9

2.6 Connect Cable ........................................................................................................................................................................................... 9

2.7 Install 3rd Party PCIe card ........................................................................................................................................................................ 10

2.6.1 Aux Power Connectors ................................................................................................................................................................. 10

2.6.2 High Power PCIe card installation................................................................................................................................................. 10

2.7 Plug-in Power to Expansion unit ............................................................................................................................................................. 10

2.8 Power ON Host computer ....................................................................................................................................................................... 11

2.9 Hardware Check...................................................................................................................................................................................... 11

3Other Technical Information.......................................................................................................... 12

3.1 Dipswitch Setting (SW3).......................................................................................................................................................................... 12

3.2 Bracket LEDS ........................................................................................................................................................................................... 12

4FAQ’s ............................................................................................................................................. 13

5 How to Get More Help..................................................................................................................... 14

5.1 Contacting Technical Support ................................................................................................................................................................. 14

5.2 Returning Merchandise to OSS ............................................................................................................................................................... 14

5.3 Online Support Resources....................................................................................................................................................................... 15

6Appendix A Compliance ............................................................................................................ 16

7Appendix B PCI Express General Information ............................................................................ 17

7.1 What is PCIe / PCIE.................................................................................................................................................................................. 17

7.2 How PCI Express Works........................................................................................................................................................................... 17

7.3 What is Lane............................................................................................................................................................................................ 17

7.4 PCI Express Links and Lanes .................................................................................................................................................................... 18

7.5 Form Factor............................................................................................................................................................................................. 19

8.5.1 PCI Express Sample Connectors.................................................................................................................................................... 19

7.6 Bandwidth............................................................................................................................................................................................... 20

7.7 Operation Mode...................................................................................................................................................................................... 20

One Stop Systems

OSS-PCIe-HIB38-x4 |

7.7.1 PCI Express Performance Table .................................................................................................................................................... 21

7.8 Power .................................................................................................................................................................................................... 22

One Stop Systems

OSS-PCIe-HIB38-x4 |

Advisories

Five types of advisories are used throughout this manual to provide helpful information, or to alert you to the potential for hardware damage

or personal injury.

NOTE

Used to amplify or explain a comment related to procedural steps or text.

IMPORTANT

Used to indicate an important piece of information or special “tip” to help you

CAUTION

Used to indicate and prevent the following procedure or step from causing damage to the

equipment.

WARNING

Used to indicate and prevent the following step from causing injury.

DANGER or STOP

Used to indicate and prevent the following step from causing serious injury or significant

data loss

Disclaimer: We have attempted to identify most situations that may pose a danger, warning, or caution condition in this manual. However, OSS

does not claim to have covered all situations that might require the use of a Caution, Warning, or Danger indicator.

One Stop Systems

OSS-PCIe-HIB38-x4 |

Safety Instructions

Always use caution when servicing any electrical component. Before handling the OSS Expansion chassis, read the following instructions and

safety guidelines to prevent damage to the product and to ensure your own personal safety. Refer to the “Advisories” section for advisory

conventions used in this manual, including the distinction between Danger, Warning, Caution, Important, and Note.

Always use caution when handling/operating the computer. Only qualified, experienced, authorized electronics personnel

should access the interior of the computer and expansion chassis.

WARNING

Never modify or remove the radio frequency interference shielding from your workstation or expansion unit. To do so may

cause your installation to produce emissions that could interfere with other electronic equipment in the area of your

system.

When Working Inside a Computer

1. Before taking covers off a computer, perform the following steps:

2. Turn off the computer and any peripheral devices.

3. Disconnect the computer and peripheral power cords from their AC outlets or inlets in order to prevent electric shock or system

board damage.

In addition, take note of these safety guidelines when appropriate:

To help avoid possible damage to systems boards, wait five seconds after turning off the computer before removing a component,

removing a system board, or disconnecting a peripheral device from the computer.

When you disconnect a cable, pull on its connector or on its strain-relief loop, not on the cable itself. Some cables have a connector

with locking tabs. If you are disconnecting this type of cable, press in on the locking tabs before disconnecting the cable. As you pull

connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before connecting a cable, make sure both

connectors are correctly oriented and aligned.

CAUTION

Do not attempt to service the system yourself except as explained in this manual. Follow

installation instructions closely.

One Stop Systems

OSS-PCIe-HIB38-x4 |

Protecting Against Electrostatic Discharge

Electrostatic Discharge (ESD) Warning

Electrostatic Discharge (ESD) is the enemy of semiconductor devices. You should always take precautions to eliminate any

electrostatic charge from your body and clothing before touching any semiconductor device or card by using an

electrostatic wrist strap and/or rubber mat.

Static electricity can harm system boards. Perform service at an ESD workstation and follow proper ESD procedures to reduce the risk of

damage to components. OSS strongly encourages you to follow proper ESD procedures, which can include wrist straps and smocks, when

servicing equipment.

You can also take the following steps to prevent damage from electrostatic discharge (ESD):

When unpacking a static-sensitive component from its shipping carton, do not remove the component’s anti-static packaging

material until you are ready to install the component in a computer. Just before unwrapping the anti-static packaging, be sure you

are at an ESD workstation or are grounded.

When transporting a sensitive component, first place it in an anti-static container or packaging.

Handle all sensitive components at an ESD workstation. If possible, use anti-static floor pads and workbench pads.

Handle components and boards with care. Do not touch the components or contacts on a board. Hold a board by its edges or by its

metal mounting bracket.

One Stop Systems

OSS-PCIe-HIB38-x4 |

1 Hardware Requirements

1. OSS-HIB38-x4 card as Host

2. OSS-HIB38-x4 card as Target

3. Ipass Cable x4 (OSS-PCIe-CBL-x4), qty:1

4. Gen3 x8 PCIe slot (computer motherboard)

5. SFF-8644 cables (qty 2). Cable connectors are keyed so that you cannot insert them incorrectly.

1.1 Host card Configuration

For Host mode: Set the dipswitch SW3 #1 to OFF position

1.2 Target card Configuration

For target mode: Set the dipswitch SW3 to ON

One Stop Systems

OSS-PCIe-HIB38-x4 | 2 Hardware Installation

2 Hardware Installation

The following steps will guide you through the installation of your OSS Expansion System.

2.1 Tools Required for Installation

To complete the installation of the OSS product you will need a Phillips-head screwdriver and ESD wrist strap to prevent electrostatic discharge.

2.2 Installation-Procedures Overview

Below is the concise version on how to set up the ExpressBox 3400.

1. Set the Dipswitch for each adapter card

2. Install the host adapter card

3. Install the target card

4. Connect Cable

5. Install 3rd party PCIe card

6. Connect power to expansion system.

a. Attach Power Cord

7. Power on Computer

8. Hardware Check

9. Verify Installation (via Operating System)

NOTE

It is highly recommended to install any 3rd party PCI-E cards / High Power PCIe cards after you have verified and tested that

the OSS expansion chassis is functional.

When installing 3rd Party PCIe cards, start with one card first just to see if there are any software and / or hardware issues or incompatibility

problems that may occur. This way you can troubleshoot the problem more easily and efficiently. If everything works well and there are no

configuration issues, you can proceed with the installation of the remaining 3rd party PCIe cards. Always refer to or read “3rd party

manufacturer installation guide” for further instructions.

One Stop Systems

OSS-PCIe-HIB38-x4 | 2 Hardware Installation

2.3 Set Dipswitch for each Adapter card

For TARGET card set the SW3#1 to ON position. For HOST card set the SW3#1 to OFF position

2.4 Install Host Adapter card

Install the Host adapter card in x16, x8 or x4 PCIe slot in the host computer.

2.5 Install Target Adapter card

Install the Target adapter card in the designated Upstream slot of the expansion board. Do not install the Target card in the downstream slot,

the card only works in the Upstream slot.

2.6 Connect Cable

Connect the x4 Ipass cable to the Host card and connect the other end of the cable to the Target card. Make sure the cable is locked-in the

cable port of both Target and Host cards.

One Stop Systems

OSS-PCIe-HIB38-x4 | 2 Hardware Installation

2.7 Install 3rd Party PCIe card

Plug in your PCIe card. Use any available downstream PCIE slots on the expansion board.

Make sure that all cards are fully seated in their PCIe card slots. When correctly seated, there will be a firm resistance when you pull up gently

on the card. To keep the cards in place, secure them in the enclosure with their retaining screws. After securing the cards verify that they do

not touch each other.

2.6.1 Aux Power Connectors

Some PCIe cards require extra power. The power supply should provide the extra power connectors / adapters. Some power supplies have

three 4-pin Molex AUX power connectors that can be used for providing extra power to cards and two (6+2 pin) PCIe connectors for GPUs.

2.6.2 High Power PCIe card installation

High Power PCIe cards, also known as High End PCIe cards, such as GPUs and other similar type of card requires additional power (or AUX

Power) to operate. High power PCIe cards or GPUs that requires auxiliary power should come with power adapter cables.

There are three 4-pin Molex AUX power connectors and two (6+2 pin) PCIe connectors from the power supply that can be used to provide

power to your GPUs or High Power PCIe cards.

2.7 Plug-in Power to Expansion unit

Connect power to expansion system by attaching the power cord to the power supply. Use standard ATX power supply.

Upon connecting power to the expansion board, TARGET card LEDs “POWER”(D1) and CBL will illuminate as solid green.

Tabla de contenidos

Otros manuales de Adaptador de OSS

OSS

OSS OSS-579 Manual de usuario

OSS

OSS OSS-PCIe-HIB38-x8-DUAL Manual de usuario

OSS

OSS OSS-XMC-HIB25-X8 Manual de usuario

OSS

OSS OSS-CPCIe3-3U-10GbE-x4-QUAD Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario