VS-GSLG OPERATOR INSTALLATION GUIDEVS-GSLG OPERATOR INSTALLATION GUIDE
VS-GSLG OPERATOR INSTALLATION GUIDEVS-GSLG OPERATOR INSTALLATION GUIDE
VS-GSLG OPERATOR INSTALLATION GUIDE
- 3 -- 3 -
- 3 -- 3 -
- 3 -
ReadthefollowingbeforebeginningtoinstallOSCOslidegate
operators:
1. Readtheyellow“Safety Instructions” brochure enclosed
with the packet of information. If you do not have one,
pleasecallOSCOat1-800-333-1717torequestone. Read
andfollowall instructions.
2. All electrical connections to the power supply must be
made by a licensed electrician and must observe all
national and local electrical codes.
3. A separate power-disconnect switch should be located
neartheoperatorsothatprimarypowercanbeturnedoff
whennecessary.
4. Install the enclosed warning signs on both sides of the
gate. Each sign must be plainly visible from the side of
the gate on which they are mounted.
5. Never reach between, through or around the fence to
operatethegate.
6. You must install all required safety equipment.
GATEOPERATORGATEOPERATOR
GATEOPERATORGATEOPERATOR
GATEOPERATOR
CLASSIFICATIONSCLASSIFICATIONS
CLASSIFICATIONSCLASSIFICATIONS
CLASSIFICATIONS
PRE-INSTALLATIONINFORMATIONPRE-INSTALLATIONINFORMATION
PRE-INSTALLATIONINFORMATIONPRE-INSTALLATIONINFORMATION
PRE-INSTALLATIONINFORMATION
Before unpacking, inspect the carton for exterior damage. If
youfinddamage,advisethedeliverycarrierofapotentialclaim.
Inspect your package carefully. You can check your acces-
sory box parts with the enclosed packing slip for your conve-
nience.Claimsforshortageswillbehonoredforonly30days
fromthedate of shipment.
Before installing the operator, read this manual completely
toensureallrequirementsfor proper installation are present.
Verify that the voltage to be used matches the voltage of the
operator.
SAFETYINFORMATIONSAFETYINFORMATION
SAFETYINFORMATIONSAFETYINFORMATION
SAFETYINFORMATION
ANDWARNINGSANDWARNINGS
ANDWARNINGSANDWARNINGS
ANDWARNINGS
IMPORTANT!!IMPORTANT!!
IMPORTANT!!IMPORTANT!!
IMPORTANT!!
Beforeinstallingthegateoperator, makesurethegate’sslide
isfreeandlevelthroughouttheentireopeningdistance.Ifthe
gate does not seem to operate properly, it may affect the op-
erator performance or greatly shorten the life of the unit. The
gate should be designed so that airflow through the fabric is
ampletopreventwindresistanceanddrag.
All gate operators can be divided into one of four different
classifications,dependingontheirdesign and usage.
Class I: Residential
A vehicle gate operator (or system) intended for use in a
home of one to four single-family dwellings, or a garage or
parkingareaassociatedtherewith.
Class II: Commercial or General Public Access
A vehicular gate operator (or system) intended for use in a
commerciallocationorbuildingsuch asamulti-familyhous-
ingunit(five or more single-family units), hotel,garage,re-
tailstore,orother building servicing the general public.
Class III: Industrial or Limited Access
Avehiculargateoperator(orsystem)intendedfor use in an
industrial location or building such as a factory or loading
dockareaorother locations notintendedtoservicethe gen-
eralpublic.
ClassIV: RestrictedAccess
A vehicular gate operator (or system) intended for use in a
guarded industrial location or building such as an airport
security area or other restricted access locations not ser-
vicing the general public, in which unauthorized access is
preventedviasupervisionbysecuritypersonnel.
Model VS-GSLG is intended for Class III and IV applica-
tions only.
09-05-13
The following contact or non-contact obstruction
detection devices have been approved for use
with OSCO slide gate operators as part of a UL325
compliant installation:
ContactEdges:
MillerModels*:MG0-20,MGR-20,MGS-20,andME-120
Photoeyes:
2520-441 MMTCModelIR-55photoeye,165’ with
mountinghardware
2520-031 MMTC Model E3K photoeye, 28’ with
mountinghardware
*for OSCO part numbers, contact a sales representative for details
