Origin Enigma Manual de instrucciones
Self Encrypting Drive
nigma
TM
Installation
&
User Manual
Page 2
Introduction
Thank you for choosing the Enigma SED from Origin Storage to secure your data.
Incorporating the latest 256 Bit AES hardware encrypted 2.5” hard drives from Toshiba; the Enigma SED
solution provides permanent full disk encryption on the fly, which means no speed degradation when
reading and writing data. With each Enigma SED conforming to the latest Trusted Computing Group OPAL
Self Encrypting Drive standard you can be sure your data is protected to the highest levels.
We advise you to read this manual carefully before using this product to ensure that you setup and configure
it correctly.
Box Contents
Please check the contents of the box; the following items should be included:
• Enigma SED Hardware Encrypted 2.5” Drive
• Appropriate Fitting Kit (Attached To Enigma Drive Unless “Bare Drive Only” Kit)
• SATA to eSATA Data Transfer Cable
• eSATA to USB Adapter
• CD-Rom with application software and manuals
• Software License Code(s)
• “Protected By Enigma” Sticker
• Warranty Registration Card
System Requirements
Hardware Requirements:
In order to use the Enigma SED your system must meet the following requirements:
• Intel Pentium III / AMS Duron 700 Mhz or higher
• 128MB RAM or higher
• CD-Rom or DVD-Rom drive for installing software
• Available USB 2.0 or eSATA/USB Combo port
Software Requirements:
• Windows XP Professional with Service Pack 3 or higher
• Windows Vista with Service Pack 1 or higher
• Windows 7
Enigma SED supports both 32 Bit and 64 Bit versions of the above operating systems.
Page 3
Table Of Contents
Introduction............................................................................. Page 2
Box Contents................................................................................. Page 2
System Requirements.................................................................. Page 2
Hardware Requirements.................................................... Page 2
Software Requirements..................................................... Page 2
Installation Instructions.......................................................... Page 4
Step 1 - Cloning Your Drive........................................................... Page 4
Software Installation.......................................................... Page 4
Hardware Setup.................................................................. Page 7
USB Connection....................................................... Page 7
eSATA/USB Combo Connection............................. Page 8
Cloning Your Hard Drive...................................................... Page 8
Step 2 - Fitting Your Enigma SED Hard Drive............................... Page 11
Step 3 - Activating Hardware......................................................... Page 12
Using Enigma SED.................................................................... Page 18
Contact Details.......................................................................... Page 19
Warranty Information................................................................ Page 20
Legal Notices.............................................................................. Page 21
Page 4
Installation Instructions
The Enigma SED can be installed as an upgrade for your existing hard drive; the following instructions will
guide you through the installation process including how to clone data on your existing hard drive to the
Enigma SED.
There are 3 steps to complete the installation of Enigma SED:
• Step 1 - Clone your existing drive to the Enigma SED drive
• Step 2 - Fit the Enigma SED drive in your computer
• Step 3 - Activate the hardware encryption to secure your data
Step 1 – Cloning Your Drive
Software Installation:
1) Insert the Enigma SED Software & Manual CD into your CD drive. If prompted click “Run
autorun.exe”, followed by “Allow” on the User Account Control dialogue. The Enigma SED start menu
will open.
If the start menu does not appear click on the Windows “Start” button and then select “Run”. Type
“X:\autorun.exe” (without the quotation marks) and replace “X” with the appropriate letter
corresponding to your CD drive. Click “OK” and the Enigma SED start menu should now open.
2) Click “Step 1 - Install Acronis True Image HD” button on the Enigma SED start menu.
3) On the Acronis True Image HD start menu click “Install Acronis True Image HD”.
Page 5
4) The Acronis True Image HD setup wizard will appear. Click “Next” to proceed.
5) Read the license agreement and if you agree to its terms select “I Accept This Agreement” and click
“Next” to proceed.
6) If you would like to participate in the Acronis Customer Experience Program select the relevant
option and then click “Next”.
Page 6
7) Select the type of installation you would like to perform by clicking on the relevant icon, we
recommend selecting “Typical”.
8) Select to install the Acronis software for all users or only the current user by selecting the relevant
option and click “Next” to continue.
9) The setup wizard will now show a summary of the options selected, and allow you to change any
of these by clicking “Back”. To finish the setup wizard and install the Acronis True Image HD software
click “Proceed”.
Page 7
10) Once the setup wizard has finished copying the files click “Close” to complete setup.
11) Close the Acronis True Image HD start menu by clicking the red “X” in the top right corner and exit
the Enigma SED start menu by clicking “Exit” and remove the CD from your CD drive.
Hardware Setup:
In order to clone data from your existing hard drive to your new Enigma SED, you need to use the supplied
Data Transfer Cable to connect the Enigma SED to your computer. Depending on available ports you can use
either a USB port or eSATA/USB Combo port to connect the Data Transfer Cable to your computer. If you
have an eSATA/USB Combo port we would recommend using this connection as it will allow for quicker data
transfer than USB.
Once you have determined the connection type available, follow the relevant instructions below to complete
the hardware setup.
USB Connection
1) Connect the SATA connector on Data Transfer Cable to the SATA connector on the Enigma SED hard
drive.
USB 2.0 Port
eSATA/USB Combo Port
Page 8
2) Connect the eSATA/USB Combo connector on the Data Transfer Cable to the eSATA/USB Combo
connector on the eSATA/USB adapter.
3) Connect the eSATA/USB adapter to the USB port on your computer. Windows will detect the new
hardware and automatically install the correct drivers for the device. The Enigma SED will not appear
in “My Computer” because it is not initialised.
eSATA/USB Combo Connection
1) Connect the SATA connector on the Data Transfer Cable to the SATA connector on the Enigma SED
hard drive.
2) Connect the eSATA/USB Combo connector on the Data Transfer Cable to the eSATA/USB Combo
port on your computer. Windows will detect the new hardware and automatically install the correct
drivers for the device, if it does not you may need to reboot your computer for the Enigma SED to
be detected. The Enigma SED will not appear in “My Computer” because it is not initialised.
Cloning Your Hard Drive:
Having installed the Acronis True Image HD software and connected the Enigma SED hard drive to your
computer using the Data Transfer Cable you can now clone the entire contents of your existing hard drive
to the Enigma SED by following the instructions below. This will create an exact clone of your existing hard
drive allowing you to use your Enigma SED drive in place of your existing drive without reinstalling the
operating system, applications or any of your data files.
1) Double click on the Acronis True Image HD icon on your computers desktop to launch the software.
If prompted click “Allow” on the User Account Control dialogue.
2) Enter the activation key, including hyphens, supplied with the Enigma SED when prompted and click
“Activate” to proceed.
Page 9
3) Click “Clone Disk” on the Acronis True Image HD welcome screen in the “What would you like to
do?” section.
4) On the “Clone Disk Wizard” ensure that “Automatic” is selected and click “Next” to proceed.
5) The “Clone Disk Wizard Summary” screen will now appear. The source disk and target disk to be
used in the clone process will be shown.
The source disk will usually be “Disk 1” and is the existing hard drive on your computer. The target
disk is the Enigma SED and can be checked by ensuring that the capacity shown in the “Before”
section matches that of your Enigma SED and that is it also listed as “Unallocated”. Click “Proceed”
to start the clone process.
Page 10
6) You will need to reboot your computer to complete the clone process. When prompted click
“Reboot”.
7) When your computer reboots, the clone process will start and progress bars will appear to indicate
the status. Once the clone process is complete press any key on your keyboard to shut down your
computer.
8) Disconnect the Data Transfer Cable from your computer once it is shut down. Proceed to “Step 2 –
Fitting Your Enigma SED Hard Drive”.
Tabla de contenidos
Manuales populares de Accionamiento de CC de otras marcas
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Manual de usuario
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Manual de lista de piezas
Chamberlain Garog
Chamberlain Garog D Series Manual de usuario
Parker
Parker PDS Series Manual de usuario
Festo
Festo DGC G Series Guía de configuración
Binks
Binks QS-5012-1-CE Manual de usuario
ABB
ABB RSYC-01 Manual de usuario
Rockwell Automation
Rockwell Automation PowerFlex 700S Manual del propietario
WEG
WEG DeviceNet CFW500 Manual de usuario
Siemens
Siemens SINAMICS G Hoja de datos
Siemens
Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento
SOMFY
SOMFY JR RU 30 Manual de usuario