Oriental motor BLE2 Series Manual de usuario

Brushless Motors

QUICK START GUIDE

BLE2 Series

□Motor

□Driver

Thank you for purchasing an Oriental Motor product.

Use the product correctly after thoroughly reading the section "Safety precautions" of the operating

manual.

This document describes methods till rotating the motor after connecting it to the driver.

For details about how to use the product, refer to the supplied with the driver.

Operating manual

HM-5190

Many other useful features are also available

□QUICK START GUIDE (this document)

□Mounting screw set

Package contents

Motor (sold separately)

The gure shows an

example of the

combination type.

∗Be sure to match the motor output power with the

driver output power.

Supplied with the

combination type.

□OPERATING MANUAL



To display the rotation speed of the

gearhead output shaft.

To display the conveyor transfer speed.

To set the rotation speed externally.

To suppress the motor torque.

To hold a load by the slight

position-keeping function.

To lock the data setting.

The motor can be operated by external signals

There are two types of connection cables

which cable leading directions are dierent.

(→Refer to the right gure)

To connect the motor and driver, the dedicated

connection cable is always needed.

For the round shaft type, only the cable for leading in

opposite direction of output shaft can be used.

Connection cable (sold separately)

Leading in opposite direction

of output shaft

Leading in direction of

output shaft

Model: CC__HBLF Model: CC__HBLB

ORIENTALMOTOR CO.,LTD.

The package includes the items shown below.

Be sure to ground the Protective Earth Terminal

(ground terminal) to ensure the safe use of the product.

Refer to "1 Connecting" for details, and ground securely.

For example.....

And others.....

As mentioned in the right, various

functions are available.

Operating using

external signals

p. 33

Operating in two or

more speeds

p. 40

Refer to "Convenient functions."

OPERATING MANUAL

Motor Driver

To power supply

Programmable controller,

etc.

1 Connecting 2 Operating a motor

Connector

cap

Remove

Attach

Secure

Be sure to turn down the locking lever

till the position shown in the gure.

When the power supply is turned on, the

display shows as follows.

Display: Rotation speed

0 r/min (standstill)

Single-phase

100-120 VAC

Single-phase

200-240 VAC

Three-phase

200-240 VAC

Refer to "Connecting" Refer to "Operating"

OPERATING MANUAL OPERATING MANUAL

10 mm

(0.39 in.)

Connect a power supply cable according to the power-supply

voltage specications of the driver. Prepare the power supply

cable since it is not supplied with the product.

Be sure to ground using the

Protective Earth Terminal .

Protective Earth

Terminal

Be sure to ground the product. Failure to do so may result in electric shock or damage to the product.

Static electricity may cause damage to the product if the Protective Earth Terminals are not grounded.

Note

モーター

ケーブル

モーター

Prepare a grounding wire since

it is not supplied with the product.

AWG18 to 14 (0.75 to 2.0 mm )

AWG18 to 14

(0.75 to 2.0 mm )

Insert into CN1

Motor

To power supply

Ground terminal

Connection cable

Press

50 r/min (factory setting)

Press The motor stops.

AC power ON

Turn

Accelerate

Decelerate

Change of motor speed [ Example: 50 →1000 r/min ]

The display blinks.

You can adjust the speed while blinking.

Press

Set

Adjustment

Press

CN4

CN2

Start of motor

The display changes to lighting

from blinking, and the speed will

be set.

When you start the motor next

time, it will rotate at the set speed.

This is an example for when the cable is "leading

in direction of output shaft." In the case of the

cable of "leading in opposite direction of output

shaft," the cable leading direction is opposite in

and .

Keep the locking

lever in the position

shown in the gure, and insert.

LOCAL

RUN key

STOP key

LOCAL key

MODE key

Setting dial

LOCAL LED

Operation panel

To stop the motor

Ground

Grounding

Driver

Connection for motor and cable

Lead wire

Screwdriver

Position of lever

Locking

lever

The motor rotates.

Press

The LOCAL LED

is lit in green.

The operation using the operation

panel was set, and the rotation speed

and rotation direction are alternately

continued to show on the display.

Interval of approximately 1 second

Press the LOCAL key.

Operation selection

2Rotation direction selection

∗ The gures show the round shaft type.

With the combination type, the gearhead output

shaft rotates in the opposite direction to the above

gure when the gear ratio is 30, 50, and 100.

(When the gear ratio is 30 and 50 for the 200 W type)

The motor rotation

direction changes whenever

the MODE key is pressed.

Press

L

N

L 1

L 2

L 1

L 2

L 3

Otros manuales de Motor de Oriental motor

Oriental motor

Oriental motor BMU Series Manual de usuario

Oriental motor

Oriental motor BXII Series Manual de usuario

Oriental motor

Oriental motor BX2 Driver Edition Series Manual de usuario

Oriental motor

Oriental motor FPW Series Manual de usuario

Oriental motor

Oriental motor PKP Series Manual de usuario

Oriental motor

Oriental motor NX Series Manual de usuario

Oriental motor

Oriental motor BLV Series Manual de usuario

Oriental motor

Oriental motor PK Series Manual de usuario

Oriental motor

Oriental motor World K Series Manual de usuario

Oriental motor

Oriental motor K II S Series Manual de usuario

Oriental motor

Oriental motor 2LSB10 Manual de usuario

Oriental motor

Oriental motor K Series Manual de usuario

Oriental motor

Oriental motor BLH Series Manual de usuario

Oriental motor

Oriental motor US Series Manual de usuario

Oriental motor

Oriental motor PKP Series Manual de usuario

Oriental motor

Oriental motor K II Series Manual de usuario

Oriental motor

Oriental motor K ⅡS Series Manual de usuario

Oriental motor

Oriental motor BLE23AR*S Series Manual de usuario

Oriental motor

Oriental motor 4IK25GN-AW2TJ Manual de usuario

Oriental motor

Oriental motor 2TK3GN-AW2J Manual de usuario

Oriental motor

Oriental motor 4IK25K-SW2 Manual de usuario

Oriental motor

Oriental motor AXH Series Manual de usuario

Oriental motor

Oriental motor CFK Series Manual de usuario

Oriental motor

Oriental motor K Series Manual de usuario

Manuales populares de Motor de otras marcas

Rotax

Rotax 125 senior MAX evo Manual de usuario

Kohler

Kohler K361 Manual de usuario

MTD

MTD OHV Series Manual de usuario

Kohler

Kohler COMMAND CH18-745 Manual de usuario

Mercury

Mercury D4.2L D-Tronic Manual de usuario

Selve

Selve SE Plus-RC Series Manual de usuario

Perkins

Perkins 1206E-E66TA Manual de usuario

Skov

Skov DA 174 Manual

Rossi

Rossi TX11 Series Manual de usuario

Siemens

Siemens SIMOTICS T-1FW3 Hoja de instrucciones

AL-KO

AL-KO PRO 350 Manual de usuario

MTU

MTU 12 V 4000 Lx4 Manual de usuario

Nanni

Nanni N3.30 Manual de instrucciones

Nanni

Nanni N5.160 CR2 Manual de usuario

KSB

KSB SuPreme Series Instrucciones de instalación

Hiwin

Hiwin EM1 Series Manual de usuario

Rotax

Rotax 912 i series Instrucciones de funcionamiento

Siemens

Siemens SIMOTICS XP 1MB1 Manual de usuario