ORBILOC Run Dual Safety Light Manual de usuario
RUN DUAL
QUICK GUIDE
THE SAFETY LIGHT
MADE IN DENMARK
Register for your 3-year warranty
at www.orbiloc.com/warranty
2
INTRODUCTION .................04
BASIC PRINCIPLES ...............06
WARRANTY .....................07
EN ..............................08
DE ..............................12
DA..............................16
Download a complete manual at
www.orbiloc.com/user-manual
3
© 2017 Orbiloc™. All rights reserved.
The Orbiloc name and logo are
among the trademarks of Orbiloc,
registred in the U.S., EU, NO and CN.
Our three-year warranty applies to the
Orbiloc Run Dual. Please visit:
www.orbiloc.com/warranty.
To get the most out of your new high
quality Orbiloc Run Dual
Safety Light™, please read the
Quick Guide carefully.
Congratulations on your new
Orbiloc Run Dual™
Safety Light
4
INTRODUCTION
Orbiloc Run Dual
Orbiloc Run Dual is a high quality light-
weight LED Safety Light designed to keep
you safe.
The Orbiloc Run Dual ensures that you are
easily noticeable from a long distance when
running in the dark or twilight.
Thanks to the Orbiloc Mounts you can
attach your Orbiloc Run Dual to almost
anything. As a result, the Orbiloc Run Dual
keeps you safe and sound.
Stay Safe and Visible
With Orbiloc Run Dual, others will be able
to spot you from a distance of up to ve
kilometres, which leaves them plenty of
time to react. This drastically reduces your
risk of being involved in an accident or a
dangerous situation.
NOTE! As a result of minor changes made to
the product after its initial launch, the pro-
duct’s packaging may include other mounts
than illustrated in this Quick Guide. Please
refer to www.orbiloc.com/user-manual for
the most recent version of the User Manual.
5
LENS (1)
MODE SELECTOR
RING (2)
O-RING (3)
BATTERY
SHEET (4)
CLIP
MOUNT (5)
BATTERY PACK
2 x CR2032 (6)
BASE (7)
ARMBAND (8)
EXTRA MOUNT INCLUDED
6
Please take care of your new Orbiloc
Run Dual™ and accessories. Read the
specic recommendations for each
product in our User Manual, available at
www.orbiloc.com/user-manual
If the Orbiloc Run Dual gets muddy
or exposed to sea water, please rinse
the outside of the Light with run-
ning water while turning the Mode
Selector Ring (2). Do not open or
disassemble while rinsing.
Remove the Battery Pack (6) for long-
term storage of the Light, and store the
batteries in a dry, well-ventilated area,
out of direct sunlight.
Please note that unless your Orbiloc
Run Dual Light is modied or repaired
by Orbiloc, your warranty will become
invalid.
Orbiloc is not responsible for any injury
or damage, whether direct, indirect or
accidental, resulting from the use of its
Lights or Accessories.
Care instructions Orbiloc Armband
BASIC PRINCIPLES
7
Orbiloc Run Dual Lights are manufactu-
red to the highest standards of quality
and technology, which is why we oer
a three-year warranty – absolutely free!
Simply register your Orbiloc Run Dual
within 30 days of purchase at:
www.orbiloc.com/warranty
Terms and conditions
The Orbiloc warranty does not aect
your statutory rights.
The warranty period applies to the
Orbiloc Run Dual. Accessories are not
covered by the warranty. The warranty
of the Orbiloc Run Dual is only valid
with the use of orginal Orbiloc replace-
ment parts. Use of other accessories and
replacement parts will make the warran-
ty of the Orbiloc Run Dual invalid. Other
exclusions include normal wear and
tear, oxidation, modications or altera-
tions, incorrect storage, poor mainte-
nance, negligence, and using the Light
for purposes for which it is not designed.
Warranty matters are always handled
according to our current conditions of
warranty. See the full warranty terms
and conditions at:
www.orbiloc.com/warranty
WARRANTY
8
GETTING STARTED
Register for your 3-year warranty at
www.orbiloc.com/warranty.
This is a Quick Guide. Download a complete
manual at www.orbiloc.com/user-manual.
See page 5 for illustration references.
Remove the Battery Sheet (4). Tighten
the Base (7) and you are ready to use your
Orbiloc Run Dual.
ON / OFF / STEADY / FLASH
The Orbiloc Run Dual is very user-friendly;
just turn the Mode Selector Ring (2) to the
left or right. The triangle indicates the
desired function. Flashing ( ) and Steady-
on ( ) symbols are found on the top of the
Lens (1).
ORBILOC MOUNTS
The Orbiloc Clip Mount (5) is the base mount
of the Orbiloc Run Dual. Also included is
the lightweight Orbiloc Armband (8) which
provides a secure and convenient way to
attach your Orbiloc Run Dual to your arm or
leg - tting arms or legs ranging between 24
and 40 cm (9-16 inches) in size.
9
UK
ORBILOC CLIP MOUNT
The Orbiloc Clip Mount (5) allows an easy on
and o attachment of your Orbiloc Run Dual
to your running clothes or to any of your
other running devices. The Orbiloc Clip
Mount (5) has a very strong grip, allowing it
to be attached in a downward position.
ORBILOC ARMBAND
Place the Orbiloc Run Dual on the Orbiloc
Armband. Adjust the Orbiloc Armband so
that it ts comfortably. You should be able
to place two ngers beneath the Orbiloc
Armband. Position the Orbiloc Run Dual so
that the light is facing the trac.
NOTE; For specic guides on switching and
attaching the mounts please refer to
www.orbiloc.com/user-manual
NOTE; Go to www.orbiloc.com/product/
orbiloc-dual-accessories to see other
Mounts and ways of attaching the Orbiloc
Safety Light.
10
ORBILOC SERVICE KIT
The Orbiloc Service Kit makes maintaining
your Orbiloc Run Dual quick and easy.
The Orbiloc Service Kit contains a Lithium
Battery Pack (6) (2 x CR2032) and an O-ring
(3) lubricated with silicone.
CHANGE BATTERY & MAINTENANCE
Unscrew the Base (7) of the Orbiloc Run
Dual and replace the old O-ring (3) with a
new from the Orbiloc Service Kit. Replace
the old Battery Pack (6) with a new Battery
Pack (6) (with the +symbol facing down) in
the Base (7) of the Orbiloc Run Dual.
Make sure that the Mode Selector Ring (2)
is clicked rmly to the Lens (1). Please note
that the part with the small magnet has to
be placed in one of the four semi-circles on
the Lens (1), and that the Orbiloc Clip (5) is
placed in the designated guide pins on the
Lens (1). Screw the Lens (1) and Base (7) of
the Orbiloc Run Dual together again.
NOTE; Should the light be in and out of wa-
ter often, the O-ring (3) should be lubricated
with silicone and the light should be rinsed
after each time (please refer to page 6).
Tabla de contenidos
Idiomas:
