Opvimus NS-CAN Manual de usuario
9I251 05/02/2019 V3.2.001
Noise sensor for
COMPACT SYSTEM
NS-CAN
NS-CAN version 3.2.001
3
Table of contents
1. FEATURES..............................................................................................................................................................................4
2. PARTS OF THE EQUIPMENT....................................................................................................................................................4
3. CAN BUS ADDRESS CONFIGURATION.....................................................................................................................................5
4. CONNECTION.........................................................................................................................................................................5
4.1. CAN Bus connection between NS-CAN and COMPACT unit ..........................................................................................5
4.2. Connection between NS-CAN and COMPACT-E expansion unit....................................................................................6
4.3. Power supply connection .............................................................................................................................................7
4.4. External microphone connection ..................................................................................................................................7
4.5. Connection between several NS-CAN ...........................................................................................................................8
5. COMMISSIONING THE NS-CAN ..............................................................................................................................................8
6. TECHNICAL SPECIFICATIONS ..................................................................................................................................................9
7. DIMENSIONS .........................................................................................................................................................................9
8. SOFTWARE AND FIRMWARE VERSIONS ............................................................................................................................... 10
9. DOCUMENT VERSION TRACKING .........................................................................................................................................10
10. GUARANTEE ........................................................................................................................................................................11
WARNING. This is a Class A unit. In a domestic environment this unit may cause radio interferences. In this case the user
must take the necessary precautions.
Noise sensor for
COMPACT SYSTEM
NS-CAN
NS-CAN version 3.2.001
4
1. FEATURES
Noise sensor for COMPACT system installations.
Through a CAN bus it communicates with the COMPACT audio matrix unit sending the noise level measured in the particular loca-
tion where it is placed.
Each COMPACT matrix allows connecting up to 16 units of NS-CAN.
2. PARTS OF THE EQUIPMENT
(1) Noise sensor microphone.
(2) Green led. Power indication.
(3) Red led. Error communication indication.
(4) Yellow led. RX/TX. Data reception and transmission
indicator.
(5) BUS CAN Connection terminal block.
(6) External microphone connection terminal block.
(7) POWER SUPPLY terminal block. 24 VDC.
(8) Reset button. Restarts the firmware of NS-CAN.
(9) BUS CAN ADDRESS configuration DIP switches (see sec-
tion 3. CAN BUS ADDRESS CONFIGURATION).
(10) JP2 and JP3 jumpers. Configures the CAN bus end termi-
nation.
Set jumpers JP2 and JP3 between pins 2-3 if the NS-CAN
is an intermediate element of the bus.
Set jumpers JP2 and JP3 between pins 1-2 if the NS-CAN
is a final element of the bus.
Figure 1. Front view
Figure 2. Rear view
Bus CAN
Intermediate
element
Bus CAN
end element
Noise sensor for
COMPACT SYSTEM
NS-CAN
NS-CAN version 3.2.001
5
3. CAN BUS ADDRESS CONFIGURATION
Using SW1 DIP switches assigns an address to the sensor.
Every noise sensor connected to the same bus must have a
different CAN address. Values must be between 0 and 15.
4. CONNECTION
4.1. CAN Bus connection between NS-CAN and COMPACT unit
To COMPACT unit
NS-CAN
Figure 3. CAN address configuration
Figure 4
ATTENTION: For the connection of the CAN bus it is recommended to use a shielded twisted pair AWG24 cable
(Not connected)
(Bus CAN)
24V DC
Power supply
Noise sensor for
COMPACT SYSTEM
NS-CAN
NS-CAN version 3.2.001
6
4.2.Connection between NS-CAN and COMPACT-E expansion unit
The CAN communication speed of the NS-CAN is 33.3
kbit/s. For installation with COMPACT-E expansion
units with a communication speed of 500 kbit/s, a
CAN-AV speed adapter (code A465AV) must be
inserted in the bus to match the transmission speed
between devices.
The attached table shows the transmission speed of
the equipment:
Follow figure 5 to connect the NS-CAN to the
COMPACT-E.
EQUIPMENT SPEED TRANSMISSION
COMPACT 33.3 kbit/s o 500 kbit/s (built-
in speed adapter )
COMPACT-E 500 kbit/s
MD-30C
33.3 kbit/s
ME-200C 33.3 kbit/s
NS-CAN
33.3 kbit/s
NS-CAN
Figure 5
To COMPACT or others
COMPACT-E expansion units
To COMPACT-E unit
24V DC
Power supply
(Not connected)
24V DC
Power supply
(Not connected)
Noise sensor for
COMPACT SYSTEM
NS-CAN
NS-CAN version 3.2.001
7
4.3. Power supply connection
The NS-CAN should be powered at 24VDC through the
24VDC terminal block (see figure 6).
It can also be powered through the 24V and GND con-
tacts of the BUS CAN IN terminal block (see figure 7).
4.4. External microphone connection
ATTENTION:
If you want to use an external microphone instead of the sensor's own microphone, you must change the NS-CAN configuration
using the Call Point software by enabling this option. If an external microphone is used, the microphone integrated in the NS-
CAN stops working.
Figure 8
Figure 6
Figure 7
24V DC
Power supply
24V DC
Power supply
Noise sensor for
COMPACT SYSTEM
NS-CAN
NS-CAN version 3.2.001
8
4.5.Connection between several NS-CAN
5. COMMISSIONING THE NS-CAN
Commissioning the NS-CAN requires sending of configurations to the COMPACT audio matrix to whose CAN bus the NS-CAN is
connected. To do this, you need a PC equipped with a network card and connected to the COMPACT matrix, either through a
Ethernet switch, or directly through a network cable. The PC must have the Call Point software installed.
1. Set the CAN address of the NS-CAN and its position in the BUS (end or intermediate element).
2. Make the connections between equipment.
3. Apply power to the units.
4. Via the Call Point software, configure the parameters of the NS-CAN and adjust the NS-CAN values for each zone.
(Intermediate
bus element)
(Final bus
element)
(Intermediate
bus element)
Figure 9a
CAN Bus
24V DC
Power
supply
(Not connected)
(Not connected)
Figure 9b
CAN Bus
24V DC
Power
supply
(Intermediate
bus element)
(Final bus
element)
(Intermediate
bus element)
(Not connected)
(Not connected)
Noise sensor for
COMPACT SYSTEM
NS-CAN
NS-CAN version 3.2.001
9
6. TECHNICAL SPECIFICATIONS
Protection degree IP65
Supply 24VDC
Consumption 50 mA
Communication CAN BUS. Communication speed: 33.3 kbits/s.
Weight 0.5 Kg
Cable entry 2 Cable gland PG-7 and 2 Blanking hole plugs (two PG-7 cable glands are also supplied).
Finishing Front plate in INOX.
Painted metal housing (RAL-7032).
7. DIMENSIONS
Noise sensor for
COMPACT SYSTEM
NS-CAN
NS-CAN version 3.2.001
10
8. SOFTWARE AND FIRMWARE VERSIONS
The functionalities described in this user manual are valid for software and firmware versions that are the same or later versions of:
NS-CAN Firmware Version 5.2
COMPACT Firmware Application version 3.2
Linux version 2.6.35.14
Call Point Software Version 3.2
9. DOCUMENT VERSION TRACKING
Reference system Type of Document Confidentiality N/A
NS-CAN Installation and operation guide
Rev Date Modifications Content Written by:
3.1.000 March 2017 R+D Department
3.1.001 May 2017 6. Technical specifications R+D Department
3.2.000 October 2018 4. Connection
8. Software and firmware versions R+D Department
3.2.001 February 2019 4.2. Connection between NS-CAN and COMPACT-E expansion unit R+D Department
Approved By Function Date
Ferran Gironès i Puig R+D Director 02/2019
Tabla de contenidos
Idiomas:
