Optika Italy B-150D-MRPL Manual de usuario
Model
B-150D-MRPL
B-150D-BRPL
B-150D Series
INSTRUCTION MANUAL
Ver. 2.0 2019
Page 2
1. Warning 3
2. Symbols and conventions 3
3. Safety Information 3
4. Intended use 3
5. Overview 4
5.1 B-150D-MRPL 4
5.2 B-150D-BRPL 5
6. Unpacking 6
7. Assembling 6
7.1 B-150D-MRPL 6
7.2 B-150D-BRPL 7
7.3 Assembling the microscope 8
7.4 Polarizing set (optional) 9
8. Use of the microscope 10
8.1 Light intensity adjustment 10
8.2 Coarse focus tension adjustment 10
8.3 Stage 10
8.4 Adjust the interpupillary distance 10
8.5 Diopter adjustment 11
8.6 Use of oil immersion objective 11
8.7 Aperture diaphragm 12
8.8 Use with rechargeable batteries 12
8.9 Use of the polarizer (optional) 12
9. Maintenance 13
10. Troubleshooting 14
Equipment disposal 15
Summary
Page 3
1. Warning
This microscope is a scientic precision instrument designed to last for many years with a minimum of
maintenance. It is built to high optical and mechanical standards and to withstand daily use. We remind you
that this manual contains important information on safety and maintenance, and that it must therefore be made
accessible to the instrument users. We decline any responsibility deriving from incorrect instrument use uses
that does not comply with this manual.
2. Symbols and conventions
The following chart is an illustrated glossary of the symbols that are used in this manual.
CAUTION
This symbol indicates a potential risk and alerts you to proceed with caution.
ELECTRICAL SHOCK
This symbol indicates a risk of electrical shock.
3. Safety Information
Avoiding Electrical Shock
Before plugging in the power supply, make sure that the supplying voltage of your region matches with the
operation voltage of the equipment and that the lamp switch is in o position. Users should observe all safety
regulations of the region. The equipment has acquired the CE safety label. However, users have full responsibility
to use this equipment safely. Please follow the guidelines below, and read this manual in its entirety to ensure
safe operation of the unit.
4. Intended use
For research and teaching use only. Not intended for any animal or human therapeutic or diagnostic use.
Page 4
COARSE
FOCUS KNOB
FINE FOCUS KNOB
EYEPIECE
OBSERVATION
HEAD
MAIN SWITCH / INTENSITY
ADJUSTMENT DIAL
CONDENSER
STAGE
LED CHARGE
INDICATOR
NOSEPIECE
OBJECTIVES
TENSION
ADJUSTMENT
COLLAR
SLIDE HOLDER
X/Y MOVEMENT
KNOBS
5. Overview
5.1 B-150D-MRPL
Page 5
5.2 B-150D-BRPL
COARSE
FOCUS KNOB
FINE FOCUS KNOB
EYEPIECES
OBSERVATION
HEAD
MAIN SWITCH / INTENSITY
ADJUSTMENT DIAL
CONDENSER
STAGE
LED CHARGE
INDICATOR
NOSEPIECE
OBJECTIVES
TENSION
ADJUSTMENT
COLLAR
SLIDE HOLDER
X/Y MOVEMENT
KNOBS
Page 6
6. Unpacking
The microscope is housed in a moulded Styrofoam container. Remove the tape from the edge of the container
and lift the top half of the container. Take some care to avoid that the optical items (objectives and eyepieces)
fall out and get damaged. Using both hands (one around the arm and one around the base), lift the microscope
from the container and put it on a stable desk.
Do not touch with bare hands optical surfaces such as lenses, lters or glasses. Traces of grease or other
residuals may deteriorate the nal image quality and corrode the optics surface in a short time.
7. Assembling
Once opened the box, the microscope parts are the following:
7.1 B-150D-MRPL
① Frame
② Monocular observation head
③ Eyepiece
④ Tension adjustment tool
⑤ Objectives (4X / 10X / 40X)
⑥ Dust cover
⑦ Green lter
⑧ Frosted lter
⑨ Power supply
⑩ USB cable
③
④
⑤
⑥
⑦⑧
①
②⑨
⑩
Page 7
7.2 B-150D-BRPL
③
④
⑤
⑥
⑦ ⑧
①
②
① Frame
② Binocular observation head
③ Eyepieces
④ Tension adjustment tool
⑤ Objectives (4X / 10X / 40X / 100X)
⑥ Dust cover
⑦ Green lter
⑧ Frosted lter
⑨ Power supply
⑩ USB cable
⑪Immersion oil
⑨
⑩
⑪
Page 8
7.3 Assembling the microscope
1. Remove the dust cap from the microscope frame
and from the bottom of the observation head.
2. Insert the optical head above the stand and
tighten the screw ①. (Fig. 1)
• Hold the head with one hand during the lo-
cking in order to avoid that the head falls.
3. Insert both eyepieces into the tubes of the optical
head. (Fig. 2)
• For model B-150D-MRPL: only one eyepiece
is used as this model is monocular.
4. Insert the power supply jack in the socket placed
at the rear side of the microscope. (Fig. 3)
Fig. 2
Fig. 3
Fig. 1
①
Page 9
7.4 Polarizing set (optional)
1. Place the polarizer on the light exit ①at the
base of the microscope. (Fig. 4)
2. Loosen the head xing knob ② and remove
the head from the microscope frame. (Fig.
5)
3. Insert the analyzer into the hole inside the
frame ③. (Fig. 6)
4. Put back the head into its original position
and lock the xing knob.
Fig. 6
③
Fig. 4
①
Fig. 5
②
Page 10
8. Use of the microscope
8.1 Light intensity adjustment
Operate on the light intensity adjustment dial to turn
ON / OFF the microscope and to increase / decrease
the illumination voltage ①. (Fig. 7)
8.2 Coarse focus tension adjustment
• Adjust the tension using the provided tool.
The coarse knob tension is pre-setted in the factory.
To modify the tension according to personal’s needs,
rotate the ring ② using the provided tool (Fig. 8).
Clockwise rotation increases the tension. If the ten-
sion is too loose, the stage could go lower by itself
or the focus easily lost after ne adjustment. In this
case, rotate the knob in order to increase the tension.
8.3 Stage
Stage accepts standard slides 26 x 76 mm, thickness
1,2 mm with coverslide 0,17mm. (Fig. 9)
1. Open the spring arm of the slide holder ③ and
place the slide from the front on the stage.
2. Gently release the spring arm of the slide holder.
• A sudden release of the spring arm could cau-
se the falling of the slide.
8.4 Adjust the interpupillary distance
Only B-150D-BRPL
Hold the right and left parts of the observation head
using both hands and adjust the interpupillary distan-
ce by turning the two parts until one circle of light can
be seen. (Fig. 10)
• The graduation on the interpupillary distance in-
dicator ④, pointed by the spot “.” on the eyepiece
holder, shows the distance between the opera-
tor’s eyes.
The range of the interpupillary distance is 48- 75 mm.
Fig. 7
①
Fig. 8
②
Fig. 10
④
Fig. 9
③
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Idiomas:
Otros manuales de Microscopio de Optika Italy
Optika Italy
Optika Italy B-1000 Series Manual de usuario
Optika Italy
Optika Italy IM Series Manual de usuario
Optika Italy
Optika Italy IM-5FLD Manual de usuario
Optika Italy
Optika Italy IM-5 Series Manual de usuario
Optika Italy
Optika Italy B-382PL-ALC Manual de usuario
Optika Italy
Optika Italy OPTIKAM EC2 Manual de usuario
Optika Italy
Optika Italy SZ-STL5 Manual de usuario
Optika Italy
Optika Italy B-60 Series Manual de usuario
Optika Italy
Optika Italy B-150D Series Manual de usuario
Optika Italy
Optika Italy B-383 Series Manual de usuario
Optika Italy
Optika Italy B-510 Series Manual de usuario
Optika Italy
Optika Italy B-510 Series Manual de usuario
Optika Italy
Optika Italy B-380 Series Manual de usuario
Optika Italy
Optika Italy B-150 Series Manual de usuario
Optika Italy
Optika Italy B-800 Series Manual de usuario
Optika Italy
Optika Italy B-810 Series Manual de usuario
Optika Italy
Optika Italy INSPECTION SYSTEMS Series Manual de usuario
Optika Italy
Optika Italy B-510 Series Manual de usuario
Optika Italy
Optika Italy B-1000 Series Manual de usuario
Optika Italy
Optika Italy ACCESSORIES Series Manual de usuario
Manuales populares de Microscopio de otras marcas
VWR
VWR VisiScope 384 Series Manual de usuario
Nikon
Nikon ECLIPSE E200 POL Manual de usuario
Leica
Leica DI C800 Manual
ThermoFisher Scientific
ThermoFisher Scientific Continuµm Manual de usuario
ThermoFisher Scientific
ThermoFisher Scientific Continuµm Manual de usuario
Olympus
Olympus SZ61 Manual de usuario