Optibike R Series Manual de usuario

R Series Unpacking Guide Page 1

Optibike R Series

Unpacking Guide V1.0

Congratulations on your new Optibike R Series Electric Bike.

Please take time to read through this instruction manual before

unpacking.

ATTENTION!

If you do not have the necessary skills and experience to perform the

actions in this manual, it is strongly suggested that you take the bike to a

bicycle shop to have it assembled.

R Series Unpacking Guide Page 2

Find a work area that is comfortable with lots of room around you on all

sides

Tools Needed

While we strive to make it as simple as possible to get you out on the road, you will need a few

basic tools for the job. Unpacking is easier done with two people.

Metric Allen wrench set

Pedal wrench or a quality 15mm open end wrench

Some type of cutter for opening the box (carpet knife scissors etc.)

A pair of wire cutters or pliers

Cut the straps holding the box together

R Series Unpacking Guide Page 3

Remove the lid and inspect the contents to make sure you have

everything.

The following should be in the box:

Pedals

Fox Shock pump

Tail light

Multi tool

Battery charger

Rear Fender

Fox Suspension Manual

Avid Brake Manual

Rohloff Hub Manual

Cycle Computer Manual

Any optional accessories you may have ordered.

These items will be in the compartment towards the rear of the bike

R Series Unpacking Guide Page 4

Remove the staples in all of the circled locations

Once these are removed you may remove the support pieces and boxes from the main crate, the large

box contains the front wheel and the support on top contains the rear fender

R Series Unpacking Guide Page 5

Lift the outer box up and off from the bike

Now you can see your beautiful new bike

Set the crate aside and we can start getting the bike ready. Check the bike for any shipping damage.

R Series Unpacking Guide Page 6

Put the seat on,

Slide into the seat tube and tighten with a 5mm Allen wrench. Don’t worry about getting it straight or

the correct height now you can do this later when the bike is all together

Install the Handlebars

Next get the handlebars ready, loosen up the stem bolts with a 4mm Allen and turn the bar straight. You

may tighten it lightly for now and tighten it correctly when the wheel is on it will be easier to get the

stem lined up with the front tire

Remove the Bike From the Crate

You will need a 4mm Allen

Loosen and remove the two bolts holding the top cap of the fork mount. Be careful after these are

removed because the bike can tip at this point

R Series Unpacking Guide Page 7

Installation of the Front Wheel

Next the front wheel needs to be installed. This is easier to do with two people. Remove the red brake

pad spacer from the brake caliper (when this is removed be extra careful not to squeeze the front brake

or damage may result)

Remove the axle by first flipping down the lock levers (this may vary depending on your model

fork/wheel) then unscrewing the axle.

R Series Unpacking Guide Page 8

We will now install the front wheel

First place the wheel into the fork taking care to line up the brake rotor in between the pads correctly

When this is done reinsert the axle, tighten it firmly and press the lock levers into place

R Series Unpacking Guide Page 9

Align Handlebar Stem with Front Wheel

At this point you can straddle the bike and line up the stem/bars with the front wheel (this is done purely

by “eyeballing” it) then tighten the stem bolts.

Attention: Be sure to cross tighten the stem bolts to insure they are tight.

Inflate the Front Fork

The front suspension fork is deflated for shipping so it will need to be pumped up

Start by unscrewing the cap over the air valve

Then thread the shock pump into the fork

Pump the fork to half the riders weight in psi, this pressure can be varied to suit your preferences (please

consult your Fox Shock manual for further details) Then replace the cap.

R Series Unpacking Guide Page 10

Install the Pedals

Next install the pedals taking into account they are left and right specific. They are normally marked L R

and the left one is reversed thread. Apply a little grease to the threads before threading them in.Make

sure to use a proper pedal wrench on these.

Install the Rear Fender

Install the rear fender using a 4mm Allen wrench. Pay attention not to cross thread the threads on the

bolts when inserting into frame. Adjust the straightness of the fender before final tightening.

Check the Tire Pressure

Double check the tires are pumped up to the recommended pressure on the sidewall. A good starting

pressure is 35 psi in both tires. The pressure can be adjusted higher or lower depending on the terrain

you are riding on.

The R series use Presta style inner tubes that require a special bicycle pump, available at bicycle dealers.

Otros manuales para R Series

Otros manuales de Scooter de Optibike

Optibike

Optibike M Series Manual de usuario

Manuales populares de Scooter de otras marcas

TEKTRO

TEKTRO CHEETAH Manual de usuario

Douglas

Douglas Vespa Sprint Guía de instalación

PLAYTIVE

PLAYTIVE AS-2448 Manual de usuario

Ebinger

Ebinger DONKEY XL Manual de usuario

Flyer

Flyer Mountain Guía del usuario

BackCountry eBikes

BackCountry eBikes Storm Manual de usuario

equipmed

equipmed FreeRoam II Manual de usuario

Yoto

Yoto Lion Manual de usuario

WESTHILL BIKES

WESTHILL BIKES LINK Manual de usuario

BAnff

BAnff eProdigy series Manual de usuario

Winther

Winther 475 Manual de usuario

Jetson

Jetson JBZL17 Manual de usuario

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Manual de usuario

Carrera

Carrera impel Manual de usuario

Afikim

Afikim Superlight SL-3 Manual de usuario

CareCo

CareCo ZOOM Manual de usuario

Douglas

Douglas Vespa G.S. Manual de usuario

Gazelle

Gazelle with BOSCH System Manual de usuario