Optex HX-40 Manual de usuario

-1-

N219

INSTALLATION INSTRUCTIONS

No.59-1501-2

High Mount

Outdoor Detector

High Mount

Outdoor Detector

CONTENTS

By utilising the OPTEX’s unique pyro-element,

HX series achieves high reliable detection

performance against false and missed alarms.

HX series provides stable and accurate

detection in outdoor severe environmental

conditions.

•HX-40 : standard model with two PIRs

•HX-40AM : HX-40 with IR anti-masking

feature

HX -40/40AM

Warning Warning Caution

INSTALLATION HINTS

(1) INSTALLATION HINTS 1

(2) PARTS IDENTIFICATION 2

(3) KNOCKOUTS 2

(4) DETECTION AREA SETTING 3

(5) INSTALLATION 3

(6)

BRACKET INSTALLATION AND ADJUSTMENT

(7) WIRING 6

(8) FUNCTION SETTING 7

(9) OPERATION TEST 9

(10) LED FUNCTIONS 10

(11) SPECIFICATIONS 11

Parallel

2.5 - 3.0 m

(8.3 - 10 ft.)

Tilt

Never repair or modify product Do not pour water over the

product Mount securely

Mount the detector so that a majority of traffic flow is across the detection pattern.

-2-

䎃

PARTS IDENTIFICATION

Hood

Screw (3×10 mm)

Screw (4×20 mm)

Bracket

Shaft cover

Lock screw (M4×35 mm)

Base

Bracket base

Main unitTerminals

Cover

Lock screw

Lens

LED indicator

Area

masking seal

PIR sensor

(Don not touch)

Anti-masking infrared LED

(HX-40AM only)

For wall

fastening

Wiring Hole

(Off-the-shelf) magnet switch

installation position

Adjustment screw

For switch

box fastening

For main unit fastening

Up-down

lock screw

Don’t touch

3-B Bracket

KNOCKOUTS

3-A Main unit

For wall fastening/bracket fastening

(installation pitch 83.5 mm (3.3 inch))

For bracket

up-down lock screw

For hood fastening

Wiring

knockout

Wiring sponge pad

-3-

Side view of detection area

(Installation height 3.0 m (1 ft.) )

(Installation height 2.5 m)

To limit the detection distance, apply the appropriate masking seal. Note that there are three

different types of seal.

DETECTION AREA SETTING

4-B Detection Length Adjustment

4-A Detection Area

Top view of detection area

85°

40°

30°

20°

10°

8 m

(26.7ft.)

8 m

(26.7ft.)

12 m (40 ft.)

12 m

(40 ft.)

3.0 m (10 ft.)

12 m (40 ft.)

2.5 m (8.3 ft.)

9.0 m (30 ft.)

3.0 m (10 ft.)

5.5 m (18.3 ft.)

3.0 m (10 ft.)

4.0 m (13.3 ft.)

3.0 m (10 ft.)

Out

Open the wiring knockout with suitable

tool e.g. screwdriver.

Pass the wire through the base knockout.

INSTALLATION

Wiring sponge pad

• Accessory bracket is required when the HX

is installed at 2.5m (8.3 ft.) height.

• The vertical angle of HX needs to be

adjusted 1 click (2.5° upward) to keep the

12 m (40 ft.) detection range.

See the “Caution” of 6-B for the details.

-4-

Out

Remove the up-down lock screw.

Push the shaft cover clip outwards to

remove the shaft cover.

Loosen the adjustment screw two turns.

Tilt the bracket about 45° and pass

through the wire.

Adjustment screw

BRACKET INSTALLATION AND ADJUSTMENT

20°

90° 90°

6-A Bracket installation

Using the bracket makes it possible to adjust the unit through 180° degree.

In cases where the ground is uneven and therefore not parallel with the base of the unit, it is

possible to adjust the unit vertically by ± 20 degree (see section 6-B)

Do not change the detection

distance with bracket.

Use the masking seal to

adjust the detection distance.

Caution>>

Do not loosen the

screw too much.

The screw separates

from the unit.

Caution>>

Shaft cover

Press with suitable tool.

e.g. small screwdriver

Fasten the base to the wall. Put the main unit and lens.

-5-

12 m (40 ft.)

3.0 m (10 ft.)

Out

Wiring

sponge pad

Tighten the adjustment screw clockwise.

Wire to the terminal and install the

Main unit and lens on the base.

Do the 6-B. “Set the vertical angle to

the ground” before fit the shaft cover

into place otherwise the horizontal

adjustment cannot readjust.

6-B Set the vertical angle

To have the right performance, set the vertical angle perpendicular to a ground.

Decide the wanted detection length at first. If you choose 9.0m/5.5m/4.0m, mask the

unwanted lens with masking seals. Refer to the 4-B for the details.

Act walk test to check if the vertical angle is

perpendicular or not.

Adjustment

screw

If you see the detection only

inside the designated

distance, change the

vertical angle upward. If you see the detection at

the designated distance, no

adjustment is needed.

If you see the detection

outside the designated

distance, change the vertical

angle downward.

* This is the case to have 12 meters detection length.

5Fasten the bracket to the wall.

Change the bracket direction according

to whether the Main unit is to face left

or right.

Open the wiring knockout and up-down

lock screw knockout for bracket.

Pass the wire through the base knockout

and install the base on the bracket.

-6-

9.5-18VDC

–

COM

SPSP

T.O.(NC)

AUX

(NC) (NC)

TAMPER

(NC) (NC)

TAMPER

INPUT

TROUBLE

OUTPUT ALARM POWER

–

COM

SPSP

AUX

INPUT ALARM POWER

9.5-18VDC

WIRING

*1: TAMPER terminals to be connected to a 24 hour supervisory loop.

Power wires should not exceed the following lengths.

HX-40AM

HX-40

SPARE (Non short)

ALARM OUTPUT (N.O.)

ALARM OUTPUT (COM)

ALARM OUTPUT (N.C.)

POWER INPUT (–) (9.5 - 18VDC)

POWER INPUT (+) (9.5 - 18VDC)

TAMPER OUTPUT

(N.C.) *1

AUX INPUT

(N.C.)

TROUBLE OUTPUT

(N.C.)

If the base of the unit is already parallel to the ground,

• Do not change the detection distance by tilting the unit up or down. Detection area and

length should be adjusted with masking tapes. Refer to 4-A and 4-B for the details.

• Walk test the unit to ensure that the desired detection distance is achieved.

Caution>>

NOTE: This setting is available only for the HX is installed vertically to the ground.

0° is the right setting for 3m (10 ft.)

height installation.

Adjust 1 click (2.5° upward) for 2.5m

(8.3 ft.) height installation to maintain

the 12m (40 ft.) detection range.

0°5° (2 clicks)

10° (4 clicks)

WIRE GAUGE

AWG22 (0.33 mm2)

AWG20 (0.52 mm2)

AWG18 (0.83 mm2)

HX-40 HX-40AM

12V

160m (520ft)

260m (850ft)

410m (1350ft)

14V

360m (1180ft)

560m (1840ft)

900m (2950ft)

12V

140m (460ft)

230m (750ft)

360m (1180ft)

14V

310m (1020ft)

490m (1610ft)

780m (2560ft)

-7-

Dip switch 2

8-B IMMUNITY SWITCH

(factory default)

POSITION FUNCTION

OFF

The LED lights when someone is detected.

The LED does not light even if someone is

detected

OFF

STD

(factory default)

POSITION FUNCTION

IMMUNITY

Suitable for standard applications.

Set this when used in a location with small animal,

small size pet or hostile environment.

IMMUNITY

STD

Dip switch 1

8-A LED ON/OFF HX-40

HX-40AM

HX-40

HX-40AM

FUNCTION SETTING

Dip SW

1 LED ON/OFF SELECTOR

2 IMMUNITY SWITCH

3 AUX INPUT SELECTOR

4 TROUBLE OUTPUT SELECTOR

ANTI-MASKING

SENSITIVITY

SELECTOR (8-F)

PIR SENSITIVITY SELECTOR

(8-A)

(8-B)

(8-C)

(8-D)

(8-E)

Do not touch

NOTE: For the walk test, move more than 1 m (3.3 ft.) away from

the detector.

AND

(factory default)

POSITION FUNCTION

When both the Main unit and the satellite detect

someone, the alarm is output is activated.

Set to this when not connecting a satellite unit.

Note: The alarm is not output unless both the Main

unit and the satellite detect someone within

60 seconds.

When either the Main unit or the satellite detects

someone, the alarm is output.

AND

By connecting a satellite unit (another warning sensor), you can

expand the detection area and correct false alarms.

As a satellite unit, you can use any general no-voltage contact

output (NC) warning sensor, including the following.

<Infrared (AIR) sensors, thermal line (PIR) sensors, magnet

switches, etc.>

Dip switch 3

8-C AUX INPUT HX-40

HX-40AM

-8-

HX-40

HX-40AM

PIR SENSITIVITY

SELECTOR

8-E PIR SENSITIVITY

POSITION

HIGH

MIDDLE

(factory default)

LOW Suitable for hostile and narrow area

FUNCTION

Suitable for sites requiring greater sensitivity

applications

Suitable for standard applications

LOW

MIDDLE

HIGH

(factory default)

POSITION OUTPUT TERMINAL

OFF

TROUBLE

TROUBLE and ALARM

Use this when not wiring a dedicated trouble input

terminal on the control panel.

OFF

Dip switch 4

8-D TROUBLE OUTPUT HX-40

HX-40AM

Red

Trouble output is used for anti-masking signal.

When an object is placed close to the lens surface, for a period of

more than 180 seconds, the IR Anti-Masking circuit will activate and

generate a trouble signal.

LED Operation>>

DETECTOR STATUS

Anti-Masking booting

(Anti-Masking start up)

Anti-Masking

LED Indication

Red blinks 2 times and goes

off for 5 sec.

This movement is repeated.

Red blinks 3 times and goes

off for 3 sec.

This movement is repeated.

LED operation

ANTI-MASKING

SENSITIVITY SELECTOR

POSITION

HIGH

STD

(factory default)

OFF

FUNCTION

Suitable for sites requiring greater sensitivity

applications.

Suitable for standard applications.

Suitable for sites requiring no anti-masking

function.

OFF

STD

HIGH

8-F ANTI-MASKING HX-40

HX-40AM

-9-

OPERATION TEST

9-A Example of adjustment for false alarms

If there is a road where people or vehicles can pass in front of the detection area, and

can trigger false alarms, adjust the area as follows.

Delete the unneccesory detection area (a)

using the appropriate masking seal(s) 1 2 or 3.

(Reduce the distance from 12m, 9m, 5.5m ,4m

(40ft., 30ft.,18.3ft., 13.3ft.) as determined by

the walk testing.)

Actually move and check that the system does

not detect movement on the road (a) but does

detect when you enter the detection area (b).

The detection area might increase when there

is a big temperature difference between the

moving object and the background.

For example, when the detection distance is

set to 12 m (40 ft.), sometimes vehicles 13 m

(43 ft.) away may be detected.

In this case, set the detection distance to 9 m

(30 ft.). This shortens the alarm area but it can

reduce false alarms due to vehicles.

Caution>>

Approx. 9 m

(30 ft.)

Position B

Approx. 13 m (43 ft.)

A heat source beyond the detection area may

cause the detector to cause a false alarm by

reflecting off the ground.

Examples of reflective ground is water

(puddle), wet road, smooth surface concrete

and asphalt road.

The heat source is strong and / or reflection

rate is high, detectors detection distance will

be longer than required and may detect

unwanted objects beyond. According to the

ground condition of the installation site, select

the detection range position.

Caution>>

-10-

To limit the detection range, apply the area masking seal to the section you want to hide on the

lens inside. Configure the area in such a way as to avoid having anything cut across the area.

9-B Area Masking

Pasting on example for

masking No. 5 and No. 6

Area masking seal

556

HX-40AM

HX-40

LED FUNCTIONS

DETECTOR STATUS

Alarm

Warm-up period

LED Indication

Red light

Red blinks

LED operation

Light BlinkOFF

Red

DETECTOR STATUS

Alarm

Warm-up period

Trouble

output

Anti-Masking booting

(Anti-Masking start up)

Anti-Masking

LED Indication

Red light

Red blinks

Red blinks 2 times and goes off for 5 sec.

This movement is repeated.

Red blinks 3 times and goes off for 3 sec.

This movement is repeated.

LED operation

Otros manuales para HX-40

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sensor de seguridad de Optex

Optex

Optex FTN-RRHW Manual de usuario

Optex

Optex X-ZONE Manual de usuario

Optex

Optex REDSCAN Series Manual de usuario

Optex

Optex PROWAVE AIR-SLIDE 2 Manual de usuario

Optex

Optex FMX-ST Manual de usuario

Optex

Optex Smart Line Series Manual de usuario

Optex

Optex SL-100 TNR Manual de usuario

Optex

Optex OA-FUNXION Manual de usuario

Optex

Optex RLS-3060 Manual de usuario

Optex

Optex HX-40 Manual de usuario

Optex

Optex REDSCAN mini-Pro Series Manual de usuario

Optex

Optex REDWALL-V Guía

Optex

Optex AX100 Manual de usuario

Optex

Optex CDX Series Manual de usuario

Optex

Optex REDSCAN PRO RLS-50100V Manual de usuario

Optex

Optex fit Series Manual de usuario

Optex

Optex ELITE T Manual de usuario

Optex

Optex PRO SWING OA-EDGE1 T Manual de usuario

Optex

Optex OA-6500S T Manual de usuario

Optex

Optex HX-40RAM Manual de usuario

Optex

Optex REDSCAN mini-Pro Series Manual de servicio

Optex

Optex AX-70TN Manual de usuario

Optex

Optex OA-EDGE T Manual de usuario

Optex

Optex REACTION TWO Manual de usuario

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

Siemens

Siemens AZL66 Series Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

DMP Electronics

DMP Electronics 1122INT Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario