Optex HX-80N Manual de usuario
CONTENTS
1 INSTALLATION PRECAUTIONS............2
1-1 BEFORE INSTALLATION................2
1-2 PARTS IDENTIFICATION................3
1-3 KNOCKOUTS..................................3
2 DETECTION AREA.................................4
2-1 OUTLINE OF DETECTION AREA...4
2-2 HOW TO REDUCE THE LONG
RANGE DETECTION AREA............6
2-3 HOW TO DEACTIVATE THE SHORT
RANGE DETECTION AREA............8
3 INSTALLATION.....................................10
3-1 INSTALLING WITH BRACKET......10
3-2 ADJUSTING THE VERTICAL
ANGLE...........................................12
3-3 INSTALLING WITHOUT
BRACKET......................................12
3-4 WIRING .........................................13
3-5 WALL TAMPER (OPTION) ............14
4 WALK TEST..........................................16
5 SETTING ..............................................16
6 LED INDICATION .................................18
7 SPECIFICATIONS ................................19
7-1 SPECIFICATIONS .........................19
7-2 DIMENSIONS................................20
HX-80N 2 PIRs standard model
HX-80NAM HX-80N with anti-masking
Long distance detection area (24.0 m)
Flexible detection area setting with plates and flaps
Unique pyro element
Intelligent AND logic
Dual signal processing logic
Vegetation sway analysis logic
Digital anti-masking (AM model)
•
•
•
•
•
•
•
NO.59-1619-0
INSTALLATION INSTRUCTIONS
High Mount
Outdoor Detector
HX-80N/80NAM
High Mount
Outdoor Detector
HX-80N/80NAM
- 1 -
HX-80N80NAMEN.indd1HX-80N80NAMEN.indd1 2010/08/2010:20:022010/08/2010:20:02
1INSTALLATION PRECAUTIONS
1-1
BEFORE INSTALLATION
Warning Failure to follow the instructions provided with this indication and improper
handling may cause death or serious injury.
Caution Failure to follow the instructions provided with this indication and improper
handling may cause injury and/or property damage.
The check mark indicates recommendation.
The nix sign indicates prohibition.
Warning Warning Caution
Do not repair or modify product
Keep product away from water
Mount the unit securely
Mounting height Keep the detector parallel to the ground.
Parallel Tilt
Consider the direction a person is approaching from, as well as the detection area.
Install the detector in a place where it is free from false alarm factors. For example:
Sunlight and reflection•Heat source•Objects moving in the wind•
2.5 m – 3.0 m
(8'2" – 9'10")
- 2 -
HX-80N80NAMEN.indd2HX-80N80NAMEN.indd2 2010/08/2010:20:032010/08/2010:20:03
1-2
PARTS IDENTIFICATION
1-3
KNOCKOUTS
Bracket base
Main unit
Bracket
LED indicator
Lock Screw* (M4 × 35 mm)
Lens
Base
PIR1
(Do not touch)
Terminals
Shaft cover
Cover
Lock screw
Anti-masking infrared LED
(HX-80NAM only)
Screw (4 × 20 mm)
PIR2
(Do not touch)
For wall fastening/bracket fastening
(installation pitch 83.5 mm (3.29"))
For main unit fastening
Adjustment screw
BracketMain unit
(Off-the-shelf) Universal
magnet switch install position
For bracket
Up-Down lock screw
Wiring Hole
For wall
fastening
For switch
box fastening
Do not touch
Up-Down
lock screw
Wiring
knockout
Wiring sponge pad Wiring Hole
Screw kit
For joint For wall mounting
Screw (4 × 20 mm) Screw (4 × 20 mm)
*Lock screw attached on bracket base
- 3 -
HX-80N80NAMEN.indd3HX-80N80NAMEN.indd3 2010/08/2010:20:032010/08/2010:20:03
2DETECTION AREA
a
b
d
g
i
h
j
C
2-1
OUTLINE OF DETECTION AREA
Plate 2
Flap fix position
indicator Plate fix position
indicator
Upper flap
Plate 1
Lower flap
- 4 -
HX-80N80NAMEN.indd4HX-80N80NAMEN.indd4 2010/08/2010:20:042010/08/2010:20:04
DETECTION AREA (factory default)
Caution>>
Adjust 1 click (1.25° upward) for 3.0 m (9'10") height installation. (Refer to 3-2)•
b
a
ef c
jg dhi
b
a
ef cjg dhi
0.5
1.5
2.5
2.5 m (8'2")
(m) 4 8 12 16 20 24 (m)
1.0
6
4
2
8
10
2.0
3.0
3.0 m (9'10")
(m)(ft.) 4 8 12 16 20 24 (m)
10 20 30 40 50 60 70 80 (ft.)
10 20 30 40 50 60 70 80 (ft.)
10 20 30 40 50 60 70 80 (ft.)
6
4
2
8
(ft.)
1.0
0
3
3
0
1.0
Top View
Side View
(m)(ft.) 4 8 12 16 20 24 (m)
Caution>>
Adjust 2 clicks (2.5° upward) for 2.5 m (8'2") height installation. (Refer to 3-2)•
- 5 -
HX-80N80NAMEN.indd5HX-80N80NAMEN.indd5 2010/08/2010:20:042010/08/2010:20:04
2-2
HOW TO REDUCE THE LONG RANGE DETECTION AREA
To adjust the LONG range of detection, set the upper and lower flaps as follows:
Flap fix position indicator
Upper flap
Lower flap
a
b
d
g
i
h
j
C
1Pull out the flap.
a
b
g
i
C
Note>>
If the lower flap is located at the factory default
position, slide it out with your thumb.
2Move the flap to the position that
corresponds with the desired detection
distance.
a
b
g
i
C
3Push the flap until it clicks into position.
a
b
g
i
C
- 6 -
HX-80N80NAMEN.indd6HX-80N80NAMEN.indd6 2010/08/2010:20:042010/08/2010:20:04
PIR long range detection area reduction
The detection distance in the following table can be limited by combining the positions of the
flap.
Use the following table to determine the positions of the upper and lower flaps that set the
required max. detection distance.
NOTES:
1. The distance may vary due to environmental conditions.
2. Always walk test the detector to confirm the detection distance.
NOTE: Use only the following combinations for the flap settings.
Factory default
Factory default
a
c
b
d
24.0 m
(80')
c
a
bd
N.A.
N.A.
13.0 m
(42'8")
18.0 m
(60')
N.A. 10.0 m
(32'10")
6.5 m
(22')
N.A.
12
34
Factory
default
Lower
Upper
Factory
default
2
3
4
3.0m(9'10")
6.5m(22')
5m
3.0m(9'10")
13m(42'8")
5m 10m
118m(60')
5m 10m 15m
3.0m(9'10")3.0m(9'10")
10m(32'10")
5m
MASK
MASK
MASK
MASK
Upper position: a, Lower position: Factory default
Upper position: a, Lower position: b
Upper position: c, Lower position: b
Upper position: c, Lower position: d
- 7 -
HX-80N80NAMEN.indd7HX-80N80NAMEN.indd7 2010/08/2010:20:052010/08/2010:20:05
2-3
HOW TO DEACTIVATE THE SHORT RANGE DETECTION AREA
To adjust the SHORT range of detection, set the upper and lower plates as follows:
Plate 2
Plate fix position indicator
Plate 1
* Plate 1 and 2 are identical.
a
b
d
g
i
h
j
C
1Remove the plate.
a
b
g
i
C
2Insert the plate into the position
determined by the required masking
distance until it clicks.
a
b
g
i
C
3If any plate is not used, place it in the
storage position.
a
b
g
i
C
Note>>
Be careful not to lose the plates.
- 8 -
HX-80N80NAMEN.indd8HX-80N80NAMEN.indd8 2010/08/2010:20:052010/08/2010:20:05
g
i
jh
N.A.
3
N.A.
1
N.A.
Factory
default
2
4
N.A.
PIR short range detection area deactivation
Use the following table to determine the positions of the plates that set the required masked
area.
NOTE: Use only the following combinations for the plate settings.
g
i
h
j
Lower
Upper
Not used
Not used
1
3.0m(9'10")
24m(80')
5m 10m 20m
2
3.0m(9'10")
24m(80')
5m 10m 20m
3
3.0m(9'10")
24m(80')
5m 10m 20m
4
3.0m(9'10")
24m(80')
5m 10m 20m
MASK
MASK
MASK
MASK Upper position: Factory default, Lower position: j
Upper position: i, Lower position: j
Upper position: i, Lower position: h
Upper position: g, Lower position: h
- 9 -
HX-80N80NAMEN.indd9HX-80N80NAMEN.indd9 2010/08/2010:20:052010/08/2010:20:05
Use the bracket for normal installation. The unit may be installed directly on the wall, without
the bracket, only if the following three conditions are met;
The mounting height is less than 3m (9'10").
Horizontal adjustment is not necessary.
The ground must be level.
3-1
INSTALLING WITH BRACKET
Using the bracket makes it possible to adjust the unit horizontally by ±90°.
In cases where the ground is uneven and/or not parallel with the base of the unit, it is possible
to adjust the unit vertically by ±20°.
•
•
•
Caution>>
Do not change the detection
length with bracket.
Use the flaps and plates to
adjust the detection length.
90° 90° 20°
20°
3INSTALLATION
1Remove the Up-Down lock screw. 2
Push the shaft cover clip straightly to
remove the shaft cover
.
Push with suitable tool.
e.g. small screwdriver
Shaft cover
Shaft cover clip
3Loosen the adjustment screw two turns.
Adjustment screw
Caution>>
Do not loosen the
screw too much.
It may disassemble.
4Tilt the bracket about 45° and pass
through the wire.
In
Out
- 10 -
HX-80N80NAMEN.indd10HX-80N80NAMEN.indd10 2010/08/2010:20:052010/08/2010:20:05
Otros manuales para HX-80N
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Accesorios de Optex
Optex
Optex V2 Series Manual de usuario
Optex
Optex Reaction One Manual de usuario
Optex
Optex OA-FLEX LITE Manual de usuario
Optex
Optex OVS-01GT Manual de usuario
Optex
Optex Prosafe OA-1V Manual de usuario
Optex
Optex OA-FLEX AIR T Manual de usuario
Optex
Optex ViiK Exposed Type OVS-02GT Series Manual de usuario
Optex
Optex VIBRO Manual de usuario
Optex
Optex Accurance-3D A3001CB Manual
Optex
Optex Elite OA-603 Manual de usuario
Optex
Optex OA-FLEX T Manual de usuario
Optex
Optex BGS-V2000 Series Manual de usuario
Optex
Optex Redscan Mini Manual de usuario
Optex
Optex OA-FLEX T Manual de usuario
Optex
Optex X-ZONE Manual de usuario
Optex
Optex i-OneX T Manual de usuario
Optex
Optex OA-FLEX AIR T Manual de usuario
Optex
Optex OVS-01GT Manual de usuario
Optex
Optex AX-250PLUS Manual de usuario
Optex
Optex OAM-DUAL T Manual de usuario
