Ops-Core RAC Manual de usuario
RAC™HEADSET
Operator’s Manual
OM101116-00 REV. C
Compatible with: FAST®Maritime, FAST Ballistic High Cut,
FAST Carbon, and FAST Base Jump Helmets
RAC HEADSET
Operator’s Manual
Headset Features
Headset Components
Included / Optional Items
Preparing Headset for Use
Installing Batteries
Attaching Headset to Helmet
Attaching Pile Fasteners
Moving the Microphone
Donning and Dofng Helmet with Headset
Understanding Headset Positions
Basic Donning
Using Ventilation Mode
Dofng
Using Wireless Earbuds
Headset Functions
Maintenance
Operator Notes
2
4
5
6
7
9
10
11
13
13
14
16
17
18
20
22
24
1
2
RAC HEADSET
Headset Features
•3D Hearing Technology (3DHT)
By coupling a patented ear simulator design with binaural audio and advanced audio processing the RAC
Headset delivers hear-through audio that accurately preserves azimuth and elevation cues to provide
situational awareness. Smooth compression algorithms eliminate “clipping.”
•FAST ARC Rail Attachment
The RAC Headset attaches to the rear of the FAST ARC Rails leaving the top portion of the rails free for
mounting accessories, such as lights, cameras, etc.
•Noise-Cancelling Microphone
Mounts to left or right earcup.
•Integrated Microphone Mounting & Connection Point
Accepts mask microphones with U-173/U standard plug.
•Arm Articulation/Latch
Ventilate mode allows the ear cups to be set in ready position, near, but not pressing on the user’s head.
•Single Point Gimbal Attachment
360˚ adjustment instead of conventional adjustment systems.
•On/Off/Volume/Balance Control
Provides operator full control to personalize the listening experience to suit individual needs. Optional
Speaker/Ear Plug Switch used with Inductance Driver System to switch between speaker and earplug.
3
•Ear Cushions
High performance to ergonomically t the head geometry, providing a better seal and increased noise
attenuation.
•Streamlined Stowage
Earcups rotate to the rear of helmet when not in use, creating a very low prole.
•Quick-Release Downlead Connection
Helmet/headset can be disconnected from the downlead, allowing users to easily remove the helmet as
there are no excess cables to consider.
•Inductance Receiver Earplug
Un-tethered double-layer hearing protection provides noise attenuation in excess of typical Active Noise
Reduction (ANR) equipped headsets. Earplugs are battery-free.
•Weight
1.1 lbs (500 g) base version
1.2 lbs (545 g) with earplug option
•Immersible
IP-67 immersible
IP-68 immersible to 3 m for short durations
•Environmental
Tested to MIL-STD-810G
•EMl
Tested to MIL-STD-461E
•Export Classication
EAR-99
•Available Colors
Tan, Black, Green, and Gray
4
HEADSET COMPONENTS
Cable Guides
Cable
Earcup
Hear-Through
Microphones
Ear
Seals
Earcup
Battery
Compartment
Battery
Compartment
Volume / Function
Buttons
Mic Boom
Attachments
Points
Boom Microphone
Pivot
Arm
Button
Pivot
Arm
Button
5
INCLUDED / OPTIONAL ITEMS
Items Included with Headset:
•(2) AAA Batteries (to install into earcups)
•Pile Fasteners (to attach to helmet for cable stowage)
•Cable Loop (for cable stowage)
•Utility Pouch (to store headset)
Optional Items (Specify When Ordering Headset):
•Earbuds (wireless and battery-free)
•Foam tips for use with earbuds (three sizes: Standard, Slim, and Large)
(2) AAA Batteries Pile Fasteners Cable Loop
Foam Tips
Earbuds
Utility Pouch
6
PREPARING HEADSET FOR USE
To prepare the headset for use, you will:
1. Install the AAA batteries (one in each earcup)
2. Attach the headset to the ARC Rails on the helmet
3. Attach the pile fasteners to the helmet
4. Move the microphone to the other earcup (if needed)
7
Installing the Batteries:
NOTE: Also follow the applicable steps below to replace the batteries.
1. Remove the (2) AAA batteries from the packaging.
2.Pry the ear seal away from the earcup by pressing the tab at the bottom.
3.Insert the battery into the battery
compartment making sure to align the
battery so that the polarity marks (+ and -)
on the battery align with the corresponding
markings in the earcup battery
compartment.
NOTE: Always replace batteries
from both earcups as a set, do not
mix-and-match batteries.
CAUTION: When performing Step 2, be careful not to damage the
rubber seal in the groove on the underside of the earseal.
INSTALLING BATTERIES
+
Positive
-
Negative
Rubber Seal
8
INSTALLING BATTERIES
4.Reinstall the ear seal, ensuring that it is securely snapped to the
earcup all around the edges.
CAUTION: Be careful not to pinch the ear seal in the
groove when snapping it closed.
5.Repeat Steps 2-4 to install the other battery into the other earcup.
NOTE: Remove batteries before storing RAC Headset
for extended periods of time.
Tabla de contenidos
Otros manuales de Auriculares de Ops-Core
