Open Sesame Door Systems 133 Manual de usuario
Open Sesame Door Systems, Inc.
Manufacturer of Disability Access products
1.800.673.6911
PLEASE KEEP THIS GUIDE
FOR FUTURE INSTALLATIONS
INSTALLATION GUIDE
INSTALLATION
GUIDE
Thank you for your purchase of the Open
Sesame Automatic Door System. This product
is designed to be durable and provide
years of reliable service.
To ensure the Open Sesame Door System lives
up to all expectations, it is important to read
and comply with this installation guide.
If there are further questions about the
operation or performance of the door system,
contact us at (800) 673-6911. Our business hours
are 9am - 5pm pacic standard time.
WARNING!
It is important to read and follow the
instructions provided in this Installation Guide.
This will equip you with all the necessary
information and allow for correct
installation and proper use.
1
INSTALLATION
GUIDE
TABLE OF CONTENTS
Recommended tools for installation ....................2
...........................3
Selecting Mounting Format/Left Hand Conversion .....4
Electric Strike/M233 Clutch Adjustment ................5
Door Mount Instructions (Option A) ..................6-7
Lintel Mount Instructions (Option B) ...................8
Parallel Mount Diagram (Option C) .....................9
Residential Installation Wiring Diagram ...............10
French Door-One Operator Diagram .................. 11
French Door -Two Operators-Two Strikes Diagram..... 12
Functionality Adjustments ............................ 13
.............. 13
Model 233 Clutch Adjustment .........................14
Programming Instructions for Remote Controls
Erasing all transmitter codes
.............................. 16
....................................17-18
Model 133 Diagram .................................... 19
Model 233 Diagram ...................................20
2
RECOMMENDED TOOLS
FOR INSTALLATION
1. Ladder or Step stool
2. Tape measure
4. Phillips #2 Screwdriver
5. 5/32” or 4mm Allen wrench
6. Wire Cutters
7. Wire Strippers
8. Oscillating Multi Tool
(recommended for Strike Installation)
9. Loctite (for arm screw if removed)
10. Drill/Driver with #2 & #3 Phillips Bits
3
INSTALLATION
GUIDE
WHAT YOU WILL FIND IN THE BOX:
1. Door operator with wiring kit and wall transformer
2. Remote Control(s) – if required
3. Electric Strike(s) & Strike Tester – if required
- For Electric Strike Installation, refer to separate
instructions included with the strike
4. Screw pack
a) 2 Phillips self tapping screws 1 ¼”, for mounting
arm to metal
arm to wooden frame or door
c) 4 Phillips #8 – 1 ½” serrated screws for attaching
mounting plate to door or frame
d) Hold-down screws for laying out transformer and
e) Allen wrench 5/32” or 4mm for tightening the arm
f) Model 233 Clutch Adjustment Tool
5. Owners Manual
- Leave with Owner with your contact info
4
SELECTING THE
CORRECT MOUNTING FORMAT
*ALL DOORS DISPLAYED ARE VIEWED FROM THE INSIDE*
LEFT HAND DOOR CONVERSION
Remove color coded wires from color push-down terminals
and remove wire cord. Locate the gray transfer tube at lower
left corner behind the battery, pinch together colored wires
and feed through tube. Reconnect wires as before to color
coded terminals. Locate direction slide switch and slide
towards hinges.
*Unless specied at the time of ordering, the operator is provided in
the setup for Right Hinges. If you have hinges on the Left, you will
need to change the direction of the wires.
LEFT SIDE HINGES LEFT SIDE HINGES
LEFT SIDE HINGES
RIGHT SIDE HINGES RIGHT SIDE HINGES
RIGHT SIDE HINGES
OPTION A: DOOR MOUNT
DOOR
OPENS
INWARD
OPTION B: LINTEL MOUNT
DOOR
OPENS
OUTWARDS
OPTION C: PARALLEL MOUNT
OUTSWING
DOOR
+
WANT A WIDER
OPENING
SAFETY NOTE:
Secure door before
starting process to
ensure no one tries
to open the door
during installation.
Wires need to
be disconnected
from terminal
before rerouting
(Red/Black &
Green/Yellow)
Tube where
wires need to
be rerouted
through
Inside view
with all
components
Inside view
of empty
case
5
INSTALLATION
GUIDE
ELECTRIC STRIKE
(ADAMS RITE ONLY)
If an electric strike is used, follow the instruc-
tions included in the packaging from the electric
strike manufacturer to assemble the strike and
install it in the door jamb.
STRIKE SETTING
Adam Rite 7440 Electric Strikes are provided in
the “fail secure” mode which is required.
Connect the green wire to one black strike wire
(either one), and the yellow wire to the other
black wire.
6
Before beginning, secure door so it does not move
during installation and set up your ladder/stool.
Once you have the measurements down,
position the operator and screw into position.
Remove molding for ush mounting against
the wall.
Operator will need to be on the top corner closest
to the hinges.
On the door measure 3” away from the hinges for
Model 133 and 4” for Model 233, then create a mark.
This is where the operator will need to be positioned.
On the door jamb, measure 13” and create a mark, this
is where the middle of your arm will need to be posi-
tioned. The bracket will need to be as ush as possible
with the wall. Do not mount this bracket at an angle.
DOOR MOUNT INSTALLATION
INSTRUCTIONS FOR INWARD OPENING DOOR
**Remove Cover from Operator before beginning installation**
NOTE: Images are based on Residential Installation (Model 133)
LEFT
HINGES
RIGHT
HINGES
3”
ARM13”
3”
Mount operator at 3” away from the hinges and
mount the arm at 13” from hinges
(unless it is used for commercial installation).
Mount operator at 4” away from the hinges and
mount the arm at 13” from hinges.
Refer to separate instructions
included with the strike
FOR MODEL 133
OPERATORS:
FOR MODEL 233
OPERATORS:
FOR ELECTRIC
STRIKE INSTALLATIONS:
REMOVE MOLDING
7
INSTALLATION
GUIDE
With the door closed, adjust the arm to 90 degrees.
Strike Connection: Connect Green and Yellow wires
from phone jack to strike.
Power Connection: Red & Black cables need to run
from phone jack to transformer.Transformer is then
plugged in to 120VAC wall outlet.
Connect the operator to the phone jack.Turn unit on
and move on to page 9.
Line up the arm with marking you did on the door
jamb so that the middle of the shoe is position where
the mark is,then screw into place.Do NOTmount arm
shoe too high above operator because it will cause
binding of joints leading to screws falling off.
After setting up the correct adjustment tighten the
arm with the supplied 4mm allen wrench.
Plug in StrikeTester to RJ-11 phone jack to test electric
strike,you should hear a buzzing sound coming from
the strike (Do NOT connect any wires to this tester).
ARM13”
POWER=
RED
BLACK
PHONE
JACK
TRANS-
FORMER
STRIKE
STRIKE=
GREEN
YELLOW
STRIKE TESTER
8
LINTEL MOUNT INSTALLATION
INSTRUCTIONS FOR OUTWARD OPENING DOOR
**Remove Cover from Operator before beginning installation**
REMOVE MOLDING
FOR FLUSH MOUNTING
AGAINST THE WALL
SCREW BRACKET
INTO UNDERSIDE
OF LINTEL
POSITION ARM 13” FROM
THE EDGE OF THE DOOR
& SCREW IT
IN THE
DOOR
SCREW OUTER CASE
INTO WOOD HEADER
ADJUST THE ARM TO BE AT 90º
AND TIGHTEN IT WITH
SUPPLIED 4mm
ALLEN WRENCH
LINTEL
MOUNTED
OUTWARD
OPENING
DOORS
141”
3”
13”
13/8”
Note: Position Model 133 at 3” and Model 233 at 4” away from hinges and
mount arm at 13” from hinges. Mount arm shoe 1 3/8“ down from top of the
door. After mounting unit, see page 9 and review instructions on inside cover.
Otros manuales para 133
2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sistema de apertura de puertas de Open Sesame Door Systems
