Onkyo HT-S3900 Manual de usuario

Service Manual

Published by Onkyo & Pioneer Corporation Grobal CS Department

SAFETY-RELATED COMPONENT WARNING!! : COMPONENTS IDENTIFIED BY MARK ON THE SCHEMATIC DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE THESE COMPONENTS WITH ONKYO

PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL. MAKE LEAKAGE-CURRENT OR RESISTANCE MESUREMENTS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT BEFORE

RETURNING THE APPLIANCE TO THE CUSTOMER.

This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products

such as those covered by this manual.

Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair

to a qualified servicetechnician.

Ref.No. 4628

Pre Issue (Feb-2017)

HT-S3900

= HT-R397 + HTP-395(SKF-395, SKC-395, SKR-395, SKW-395)

HT-S3900

5.1-Channel Home Theater System

Title Page

CONTENTS

✔Title Page (This page)

✔Note for Parts List

✔Panel

✔Reset

✔Firmware

✔Hookup and Setting

✔Trouble Shoot

✔Schematic Diagram

✔Exploded View

✔Appendix

HT-R397SKF-395

SKC-395

SKR-395 SKW-395

543

1 6

543

1 6

Note for Parts List

COMMON

D 120V AC

G 220～230V

H 220～230／240V

J 100V AC

M 220～240V AC

P 230V AC

U 100～240V AC

V 110～240V

W 120V／220～240V

Speaker System (without AMP.) :

0 Passive Subwoofer

F Front Speaker

C Center Speaker

R Rear Speaker

B Back Speaker

A Australia

B United Kingdom

C North American

D USA

F Taiwan

J Japan

K Korea

L Russia

P Europe

Q Hong Kong

R China

S Brazil

T Thai

U Worldwide

Speaker System (without AMP.) :

L Left channel

R Right channel

0 Center channel

Voltage（電圧記号） Destination（仕向地記号）

When parts list is EXCEL file, please refer to the following explanation about file name.

P L _ T X – S R 3 4 3 ( B ) M J J . x l s x

Model No. Color

File Name of Parts List File (EXCEL File)

(X) Not related to color

(B) Black (M) Wood

(BR) Brown (O) Orange

(G) Gold (R) Red

(GR) Green (S) Silver

(H) Gray (V) Violet

(K) Black (W) White

(L) Blue (Y) Yellow

(LB) Light Blue

Destination（仕向地記号）

Voltage（電圧記号）

Look at the rear panel serial number 6 digit.

○○○○○J○○○○○○○○○○

Look at the rear panel serial number 5 digit.

○○○○J○○○○○○○○○○○

Color（色記号）

543

1 6

543

1 6

HT-S3900

Panel

Front Panel

Remote Control Unit

Accessory

RC-928R

Dimensions : 435 mm (W) x 168 mm (H) x 326.5 mm (D) (171/8 in. (W) x 65/8 in. (H) x 1213/16 in. (D))

Weight (without package) : 7.7 kg (16 lb 15 oz)

• Remote control

• AAA size IEC R03 dry cell batteries (to confirm

system operation) x2

• AM loop antenna

• FM wire antenna

• Speaker cables (3 m/10 ft.) x4

• Speaker cables (8 m/26 ft.) x2

• Non-Skid Pads x20

CD TUNER

BD/DVD STRM BOXCBL/SAT GAME USB

SURROUNDSTEREOBLU E TOOTH

LISTEN ING MODE

HOME ENTER RETURN

TUNIN GPRESET

DSP

TONE

AV RECEIVER

HT-R397

PHONES

ON / STANDBY

MASTER VOLUME

USB

5V/0.5A

RECEIVER

SURR

TREBLE

DSP

AUDIO SEL

DISPL AY

TUNER

EDIT SLEEP

TUNING +

TUNING -

PRESET -PRESET +

LATE NIGHT

TOP MENU

BAND

QUICKMENU

CBL/S AT

STRM BOX

BD/DVD

Reset

543

1 6

543

1 6

HT-S3900

How to Reset the Unit

Use this procedure to reset all the receiver's settings

to the factory default. Use the front panel controls to

do this.

1. Switch the receiver into standby.

2. While holding down STEREO, press and hold

ON/STANDBY for about two seconds.

3. When you see RESET? appear in the display,

press SURROUND. OK? shows in the display.

4. Press DSP to confirm.

Firmware

543

1 6

543

1 6

How to Check Firmware Version / How to Update Firmware

HT-R397

Check to the software virsion of MAIN, HDMI & CEC (SUB) microcomputers

1. Make sure that the main unit is in STANDBY mode.

Press and hold about 3 seconds the both of " ENTER " and " STANDBY/ON " keys as same time,

Then it is appeared firmware version number.

At this time, When you press the " ENTER "key to display each UCOM version, Each time the " ENTER "key is

pressed, then indications on the FL display change as follows:

2. Turn the unit off.

MAIN Ucom "ENTER"

MAIN Xx.xx "ENTER" "ENTER" "ENTER"

SUB Ucom

SUB

zzz.zz

CEC

Vy,yy DSP

firmware All segments

lit.

"ENTER"

Firmware

543

1 6

543

1 6

HT-R397

[Necessary Tools and Connections]

1 MAIN microcomputer

• PC with a serial port

•RS-232C cable (9-pin to 9-pin, straight cable) (Marketing product)

•UPDATE jig: GGF1642 (with 10P to 10P FFC)

• Firmware

• Firmware Writer Application for PC

(Flash Programmer M16C Flash Starter M3A-0806 Software)

https://www.renesas.com/

Connect as shown in the below figure and follow the procedure as below

1. Install the software for updating on the PC

2. Unplug the AC Cord of the main unit

3. Insert the FFC with its contact surface facing the " mark.

2 HDMI & CEC (SUB) microcomputer

• PC with a USB port

•USB cable (Marketing product)

•UPDATE jig: GGF1642 (with 10P to 10P FFC)

• Firmware

• Firmware Writer Application for PC

(Cypress/Spansion FLASH MCU Programmer for FM0+/FM3/FM4)

http://www.spansion.com/support/microcontrollers/developmentenvironment/Pages/mcu-

download.aspx

Connect as shown in the below figure and follow the procedure as below

1. Install the software for updating on the PC.

2. Unplug the power cord of the main unit.

Connect the FFC of the updating jig for updating to the main unit.

(Orient the FFC so that the conductive surface of

the connector faces the triangular a symbol.)

3. Start the software for updating on the PC.

No Necessary connect Main and HDMI&CEC at the same time

When you update Main, you connect Main only.

When you update HDMI&CEC, you connect HDMI&CEC only.

Preparation of Update

When you have no “UPDATE jig GGF1642,

Please order ONKYO service parts dept.

Straight Cable Adapter JIG's side

10P

RS-232C

Straight cable

PC (MAIN

microcomputer)

Rear side

10P to 10P FFC

UPDATE jig

GGF1642

Firmware

543

1 6

543

1 6

How to Update (Main MCU) 1/5

HT-R397

Microcomputers update

[Procedures]

for MAIN microcomputer

1. Unplug the AC cord.

Connect the FFC cable.( MAIN microcomputer )

Start up application "FlashSta" on the PC.

2. Plug the AC cord. (STANDBY mode)

For updating of the MAIN microcomputer, proceed with

the following steps in STANDBY mode.

Select for COM port.

[ if the following messages are displayed ]

Please push the cancel button and press the JIG's

RESET button.

And confirm a connection of FFC.

Please return to procedure 1.

3. Press the OK button.

3 Press OK button

to go to next step.

2. Enter ID.

Enter "ff" in all field.

1 Selection of upgrade file

Press the OK

2 Enter ID.

Press the OK button.

4. Select the update file and enter ID.

Note:

You need COM port number on Windows system

“My computer”, “Right Click”, “Properties”, “Device manager”

Click COM port properaties and Make sure COM port number.

Firmware

543

1 6

543

1 6

How to Update (Main MCU) 2/5

HT-R397

5. Set speed update and update the MCU.

1 Set speed of update.

Press the OK button.

1 Set speed of update. Set

Baud rate to 38400.

2 Update the MCU.

E.P.R=>Erase+Program+Read

2 Update the MCU

Press the E.P.R … button

Click on "Open" 3 to open the File Selection window.

Select Intel Hex files (*.hex) in File Type.

If the following messages are displayed, shut the

update program down, and start the update again

from step 1.

Select the 9600 of the Board rate

then press the OK button

Press the OK button. Press the Exit button.

Please wait for until this window

disappears.

6. Update Finished MAIN microcomputer. 7. Unplug the AC cord.

Disconnect the FFC cable.

Push the JIG’s RESET button during 1

sec.

Press the OK button.

Firmware

543

1 6

543

1 6

How to Update (HDMI Sub MCU) 3/5

HT-R397

for HDMI & CEC (SUB) microcomputer

[Procedures]

To perform updating, proceed as follows:

1. Set the values for Target MCU and Crystal Frequency, as

follows:

Target MCU: MB9AF156M/N/R 1

Crystal Frequency: 4MHz 2

2. Specify the software file to be updated.

Click on "Open" 3 to open the File Selection window.

Select Intel Hex files (*.hex) in File Type

3. Specify the COM PORT.

Click on "Set Environment" 4 to open the Environment Setting window.

Assign the COM PORT number 5, according to the environment.

Click on "OK" 6to close the Environment Setting window.

Click on "Full Operation (D+E+B+P)"7.

5. After the window shown below is displayed, turn the main unit on.

6. Press the Reset button of the updating jig for updating.

7. When it is appeared below window, Then power turn on unit (ON)

8. Click on "OK" 8.

Firmware

543

1 6

543

1 6

How to Update (HDMI Sub MCU) 4/5

HT-R397

9. The indications in the window change, as indicated

below:

10. Updating has been successfully completed if

"Full Operation OK!" is displayed.

Note:

If an error message like the one shown below is displayed, after checking the

connection of the updating jig for updating and the COM PORT setting, start

updating again from Step 1.

11. Turn the main unit off then disconnect the updating jig for updating.

12. Perform Factory Reset on the main unit.

Or You have to make sure that It is necessary to turn on the unit at procedure 7

Otros manuales para HT-S3900

Otros manuales de Sistema de cine en casa de Onkyo

Onkyo

Onkyo HT-R960 Manual de usuario

Onkyo

Onkyo HTC-V10X Manual de usuario

Onkyo

Onkyo HT-S8409 Hoja de especificaciones

Onkyo

Onkyo HT-S590 Manual de usuario

Onkyo

Onkyo LS5200 Manual de usuario

Onkyo

Onkyo AVX-390 Hoja de especificaciones

Onkyo

Onkyo HT-S4505 Manual de usuario

Onkyo

Onkyo HT-S570(S) Manual de usuario

Onkyo

Onkyo HT-S7100 Hoja de especificaciones

Onkyo

Onkyo PTS-307 Manual de usuario

Onkyo

Onkyo TX-NR609 Instrucciones de montaje

Onkyo

Onkyo HT-SR800 Manual de usuario

Onkyo

Onkyo AVX-760LD Manual de usuario

Onkyo

Onkyo HTP-348 Manual de usuario

Onkyo

Onkyo HT-RC550 Manual de usuario

Onkyo

Onkyo HTS5300B Manual de usuario

Onkyo

Onkyo HT-S870 Manual de usuario

Onkyo

Onkyo HT-S580 Manual de usuario

Onkyo

Onkyo HT-R960 Manual de usuario

Onkyo

Onkyo HT-S3505 Manual de usuario

Onkyo

Onkyo HT-S5910 Manual de usuario

Onkyo

Onkyo HT-S7300 Manual de usuario

Onkyo

Onkyo HT-S5300 Manual de usuario

Onkyo

Onkyo HT-S780 Manual de usuario

Manuales populares de Sistema de cine en casa de otras marcas

Samsung

Samsung HT-ES4200K Manual de usuario

Harman Kardon

Harman Kardon HS 100 Manual de usuario

Samsung

Samsung HT-P10 Manual de usuario

Philips

Philips HTS5131 Instrucciones de funcionamiento

Goodmans

Goodmans GDVD19SWS Manual de usuario

Moxi

Moxi media center Manual de usuario

Samsung

Samsung HT-EM35 Manual de usuario

LG HE903PAW Manual de usuario

Bose

Bose SoundTouch 520 Manual de usuario

Sony

Sony BDV-N990W Manual de usuario

Manta

Manta GK-500 Manual de usuario

Sharp

Sharp SBW800 Manual de usuario

Philips

Philips HTS3541 Manual de usuario

LG LHT799 Manual de usuario

Samsung

Samsung HT-TWZ415 Manual de usuario

Loewe

Loewe REFERENCE 52 SL FHD+ 200 NMP Manual de usuario

Samsung

Samsung AH68-02166R Manual de usuario

RCA

RCA 600-Watt Manual de usuario