One Forall CURC4110 Manual de usuario

Contents

Introduction................................................ 2

Features and Functions.............................. 2

Key Charts................................................... 3

Device Table................................................ 4

Installing Batteries ..................................... 4

Programming Device Control.................... 5

Searching For Your Code ........................... 6

Checking the Codes.................................... 6

Re-Assigning Device Keys .......................... 7

Changing Volume Lock.............................. 7

Clearing Custom Programming................. 8

Restoring Factory Default Settings ........... 9

Troubleshooting......................................... 9

Additional Information............................ 10

Limited Lifetime Warranty ...................... 22

Contentu

Introduction.............................................. 11

Caractéristiques et fonctions................... 11

Tableaux des touches............................... 12

Tableau des appareils............................... 13

Installer les piles ....................................... 13

Programmer la commande

des appareils............................................. 14

Rechercher votre code ............................. 15

Vériﬁer les codes ...................................... 16

Réaffecter les touches d’appareil............ 16

Changer le verrouillage de volume......... 17

Effacer la programmation

personnalisée............................................ 18

Rétablir les paramètres par

défaut de l’usine ...................................... 18

Dépannage ............................................... 19

Autres renseignements............................ 20

Garantie à vie limitée............................... 23

Universal

Remote Control

Télécommande

universelle

Owners Manual CURC4110

Guide de l’utilisateur

Introduction

This One For All 4-Device Universal Remote Control

(CURC4110) is designed to operate up to four home

entertainment devices. Its sophisticated technology

allows you to consolidate your original home

entertainment remote controls into one easy-to-use

product.

Advanced features include:

• Intuitive buttons to allow easy access to functions

and menus on your DVD player, PVR (or DVR), and

Cable, Satellite or Digital TV converter devices

• Direct code setup for easy device programming

• Step-and-Set code search and Code Verication for

an alternate way to program devices

• Volume Lock/Unlock feature to lock or unlock the

volume control to one mode or individual modes

• Device Key Re-Assignment to operate a second,

duplicate device

• Color-coded keys to quickly locate popular functions

• Extensive code library for popular video devices

including DVD players and PVRs (or DVRs)

This remote requires two (2) new AAA alkaline batteries

(not included) and some easy programming to control

your devices. For best results, please read and perform

all instructions listed here. Also, keep this guide for

future reference.

Features and Functions

Use the following illustration to locate features on this

remote. Then study the Key Charts in the next section to

learn how they function.

To ﬁnd out what type of devices can be controlled by

each device key after programming, see the Device

Table on page 4.

Key Charts When the LED (red light)

blinks, the remote control

is working and (after

programming) is sending

signals.

Press VCR, DVD, CBL/

SAT (DTC), or TV once

to select a desired home

entertainment device to

control. Also see the Device

Table on page 4.

Note: DTC stands for

Digital TV Converter.

Press PWR once to turn on

or off the selected device.

Use the keypad (1 ~ 9

and 0) to directly select

channels (e.g., 009 or 031).

Use TV/VID to switch the

TV’s input to view TV or

video programs.

Press ENTER/– once after

entering the channel

numbers on some TVs. When

you’re entering digital TV

channel numbers directly,

this button lets you separate

the main channel number

from the sub-channel

number (such as 59.1).

Press MENU (EXIT) once to display (or clear) your

selected device’s main menu.

Press GO BACK once to recall the last channel.

Use CH + (or CH -) to select the next higher (or lower)

channel.

LED

Press SHIFT in device menu systems to

use the CH and VOL keys as arrow keys

in the menu systems. Press SHIFT, then

MUTE to select the highlighted item.

Press SHIFT in DVD mode to use the

CH keys as SKIP FORWARD and SKIP

REVERSE keys (to go forward or

backward one chapter).

Press MUTE once to turn the sound off or on.

Use VOL + (or VOL -) to raise (or lower) the sound

volume.

Use Rewind, Play, Forward, Pause,

or Stop to control your VCR, PVR (or

DVR), or DVD player.

Press REC twice to record a VCR or PVR (or DVR)

program.

Use SLEEP to set the sleep timer on a selected device if

equipped with this feature.

Use SET for all programming sequences.

Device Table

NOTE: Please refer to the table below when performing

the instructions in “Programming Device Control” on

page 5.

After programming, this remote will be able to control

the following types of devices:

Device

Key Controls These Types Of Devices

• DVD Player

• TV/DVD Player Combo

• VCR/DVD Player Combo

• VCR

• TV/VCR Combo

• TV/VCR/DVD Player Combo

• VCR/DVD Player Combo

• PVR (or DVR)

• Cable Box (or Converter)

• Cable Box/PVR (or DVR) Combo

• Satellite Receiver

• Satellite Receiver/PVR (or DVR) Combo

• Digital TV Converter

• Television

Installing Batteries

1. On the remote control’s back,

push the tab and lift off the

battery cover.

2. Obtain two (2) new AAA

alkaline batteries. Match the +

and – marks on the batteries to

the + and – marks in the battery

case, then insert the new

batteries.

3. Press the battery cover back

into place. The tab should click

when the cover is locked.

4. Test the remote control by

pressing any mode key (e.g.,

TV). If the batteries are inserted

correctly, the LED (red light) will

blink.

NOTE: When batteries need replacement, the remote

control will stop operating. Remove the old batteries

and insert new ones within 10 minutes to ensure all of

your programming information is restored.

Battery Precautions:

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc) or

rechargeable (nickel cadmium) batteries.

• Always remove old, weak or worn-out batteries

promptly and recycle or dispose of them in

accordance with Local and National Regulations.

Programming Device Control

This remote is preprogrammed at the factory to operate

an RCA TV, a Sony DVD player, a Motorola cable box,

and an RCA VCR. To control devices other than the

default brands, perform the following steps; otherwise

skip this section:

1. Turn on a desired device (e.g., VCR or DVD player)

and, if applicable, insert media (e.g., cassette or disc).

NOTE: Please read steps 2 through 4 completely

before proceeding. Highlight or write down the

codes and device you wish to program before

starting step 2.

2. On the remote control, press a device key once (i.e.,

VCR, DVD, CBL/SAT (DTC), or TV).

NOTES:

• ToprogramcontrolofaVCR,PVR(orDVR),TV/VCR

Combo,orTV/VCR/DVDPlayerCombopressVCR

once. After programming a VCR Combo device,

you will be able to control channel selection,

volume, and VCR functions.

• ToprogramcontrolofaDVDPlayer,DVDPlayer/

VCRCombo,orTV/DVDPlayerCombo,pressDVD

once. After programming a DVD Combo device,

you will be able to control channel selection,

volume, and DVD functions.

• ToprogramcontrolofaCableBox,CableBox/PVR

(orDVR)Combo,SatelliteReceiver,oraSatellite

Receiver/PVR(orDVR)Combo,pressCBL/SAT

(DTC) once.

3. Press and hold SET until the LED (red light) blinks

twice, then release SET.

4. Use the accompanying code list to locate the type

of device and brand name and then enter the

ﬁrst four-digit code for your device. If performed

correctly, the LED will blink twice.

NOTE: If the LED did not blink twice, repeat steps 2

through 4 and enter the same code again.

5. Aim the remote control at the device and press PWR

(Power) once. The device should turn off. If it does not,

repeat steps 2 through 5, trying each code for your

brand until you ﬁnd one that works. If it still doesn’t

work, try Searching For Your Code on next page.

NOTE: If the device does not have a Power key,

press PLAY.

Searching For Your Code

If your device does not respond to the remote control

after trying all codes listed for your brand, or if your

brand is not listed at all, try searching for your code.

NOTE: Before performing a code search for a DVD

player or a VCR, turn on the device and insert the

required media.

For example, to search for a code for your TV:

1. On the remote control, press TV once.

2. Press and hold SET until the LED (red light) blinks

twice, then release SET.

3. Enter 9- 9- 1. The LED will blink twice.

4. Aim the remote control at the TV and slowly

alternate between pressing PWR (Power) and TV.

Stop when the TV turns off (after pressing PWR).

If the device does not have a Power key, you can

substitute another function, such as digits 0~ 9, CH

+, or PLAY).

NOTE: In the search mode, the remote control sends

IR codes from its library to the selected device,

starting with the most popular code ﬁrst.

5. To lock in the code, press and release SET. The LED

will blink twice.

6. To search for the codes of your other devices, repeat

steps 1 through 5, but substitute the appropriate

device key for the device you are searching for.

6. Repeat steps 1 through 5 for each device you want

to control. For future reference, write down each

working device code in the following boxes:

VCR Code:

Device Type:______________

DVD Code:

Device Type:______________

CBL/SAT (DTC) Code:

Device Type:______________

TV Code:

Device Type:______________

Checking the Codes

If you have set up the remote control using the

Searching For Your Code procedure above, you may

need to ﬁnd out which four-digit code is operating your

equipment.

For example, to ﬁnd out which code is operating

your TV:

1. On the remote control, press TV once.

2. Press and hold SET until the LED (red light) blinks

twice, then release SET.

3. Enter 9- 9- 0. The LED will blink twice.

4. To view the code for the ﬁrst digit, press 1once.

Wait 3 seconds, count the LED blinks (e.g., three

blinks = 3) and write down the number in the left-

most box in the TV code boxes on page 6.

NOTE: If a code digit is “0”, the LED will not blink.

5. Repeat step 4 three more times for remaining digits.

Use 2for the second digit, 3for the third digit, and

4for the fourth digit. Write down the code digits in

the remaining TV code boxes on page 6.

6. To check for codes of other devices, repeat steps

1 through 5 (starting on the previous page), but

substitute the appropriate device key for each

device you are checking.

Write down the device’s code digits in the

appropriate code boxes on page 6.

Re-Assigning Device Keys

This remote can be set to control a second PVR, VCR, or

DVD player.

For example, to control a TV, a cable box, and two DVD

players, re-assign the unused VCR key to operate the

second DVD player as follows:

1. On the remote control, press and hold SET until the

LED (red light) blinks twice, then release SET.

2. Enter 9- 9- 2. The LED will blink twice.

3. Press DVD once.

4. Press VCR once. The LED will blink twice. The VCR

key is now ready to be set up to control your second

DVD player. See Programming Device Control on

page 5.

To re-assign a second VCR or PVR (or DVR) to the unused

DVD key, repeat steps 1 through 4. However, in step 3

substitute VCR for DVD, and in step 4 substitute DVD

for VCR. Now the DVD key will be ready to be set up

as your second VCR or PVR (or DVR). See Programming

Device Control on page 5.

NOTE: Only one device can be assigned to an unused

device key at a time.

Changing Volume Lock

This remote is set at the factory for independent volume

control of each selected device. However, you can

change the Volume Lock setting to Global Volume Lock

so that a device’s volume will be locked to one mode

(e.g., to control TV volume in all other modes). After

that, if desired, you can perform Individual Volume

Unlock on a selected device to set its volume control for

independent operation.

Locking Volume Control To One Mode (Global

Volume Lock)

1. Press and hold SET until the LED (red light) blinks

twice, then release SET.

2. Enter 9- 9- 3and then press any mode key once

(e.g., TV). The LED will blink twice.

3. Now, when you press VOL +, VOL -, or MUTE,

the volume of the selected device (e.g., TV) will

be controlled, regardless of the mode you have

selected.

Unlocking Volume Control For A Single Device

(Individual Volume Unlock)

1. After performing Global Volume Lock, press a

desired mode key where you want volume to be

unlocked (e.g., DVD) and controlled within its own

mode.

2. Press and and hold SET until the LED (red light)

blinks twice, then release SET.

3. Enter 9- 9- 3and then press VOL - once. The LED

will blink four times.

4. If desired, repeat steps 1 through 3 for each device

that you want volume to be unlocked.

5. Now, after you select a device that has volume

unlocked (e.g., DVD), pressing VOL +, VOL -, or

MUTE will control the device’s volume only in its

own mode.

Unlocking All Volume Control (Restoring

Default Setting)

NOTE: Performing these instructions will restore

independent volume control for all programmed

devices(e.g.,TVvolumecontrolinTV mode, VCR

volume in VCR mode, etc.).

1. On the remote control, press and hold SET until the

LED (red light) blinks twice, then release SET.

2. Enter 9- 9- 3and then press VOL + once. The LED

will blink four times.

3. Volume will again be independently controlled

according to its default states for all programmed

devices.

Clearing Custom Programming

This remote contains an Operational Feature Reset

program. If desired, you can use it to clear custom

programming (everything except your setup codes and

reassigned device keys), and reset them to original

factory settings. (See also “Restoring Factory Default

Settings”, below.)

IMPORTANT: Executing this program will erase all your

custom settings for Volume Lock.

1. Press and hold SET until the LED (red light) blinks

twice, then release SET.

2. Enter 9- 8- 0. The LED will blink twice. The remote

control will return to normal operation.

Restoring Factory Default Settings

This remote also contains a Factory Reset program that

you can use to reset all custom settings and setup codes

to original factory settings. (See also “Clearing Custom

Programming”, above.)

IMPORTANT: Executing this program will erase all your

custom settings for Volume Lock, Reassigned Devices,

and all device settings.

1. Press and hold SET until the LED (red light) blinks

twice, then release SET.

2. Enter 9- 8- 1. The LED will blink twice. The remote

control will return to normal operation.

Troubleshooting

PROBLEM: LED (red light) does not blink when you

press a key.

SOLUTION: Replace batteries with two new AAA

alkaline batteries.

PROBLEM: LED blinks when you press a key, but

home entertainment device does not respond.

SOLUTION: Make sure the remote control is aimed at

your home entertainment device and is not more than

15 feet away.

PROBLEM: The unit does not control home

entertainment devices or commands are not

working properly.

SOLUTION: Try all listed codes for the device brands

being set up. Make sure they can be operated with an

infrared remote control.

PROBLEM: Changing channels does not work.

SOLUTION: If the original remote required pressing

ENTER to change channels, press ENTER on this remote

after entering the channel number.

PROBLEM: Tried Searching For Your Code method

and still could not ﬁnd a working code.

SOLUTION: Clear the device key as follows: Press and

hold SET until the LED (red light) blinks twice, then

release. Next enter 9- 9- 2. Then press the device key

to be cleared twice. Now repeat the Searching For Your

Code method on page 6.

PROBLEM: No remote control of volume.

SOLUTION: See Changing Volume Lock on page 7 to

lock/unlock volume.

For additional information:

• Internet: http://www.oneforall.com

Instructions to the User

This equipment has been tested and found to comply

with the limits for a class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed

to provide a reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy

and if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to

radio or television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase separation between equipment and

receiver.

• Connect equipment into an outlet or a circuit

different from that to which the receiver is

connected.

• Consult dealer or experienced radio/TV technician

for help.

Additional Information

ONE FOR ALL® is the registered trademark of Universal

Electronics Inc. Audiovox Accessories Corporation is the

Licensee of the ONE FOR ALL® brand for North America.

this publication may be reproduced, transmitted,

transcribed, stored in any retrieval system, or translated

to any language, in any form or by any means,

electronic, mechanical, magnetic, optical, manual, or

otherwise, without the prior written permission of

Universal Electronics Inc.

The One For All® 4-Device Universal Remote Control is

compatible for use in North America, excluding Mexico.

This One For All® 4-Device Universal Remote Control is

covered by one or more of the following US Patents:

6,587,067 6,496,135 5,515,052 5,959,751 6,587,067

5,481,256

CURC4110 06/09

Tabla de contenidos

Idiomas:

Otros manuales de Mando a distancia de One Forall

One Forall

One Forall AR90 Manual de usuario

One Forall

One Forall URC-7140 Manual de usuario

One Forall

One Forall URC-6410 Guía del administrador

One Forall

One Forall OARK02R Manual de usuario

One Forall

One Forall Cinema 6+ URC 6800 Manual de usuario

One Forall

One Forall URC-7140 Manual sencillo

One Forall

One Forall URC-6131 Manual de usuario

One Forall

One Forall URC7125 Manual de usuario

One Forall

One Forall DVD Expert Manual de usuario

One Forall

One Forall SAMSUNG URC-1310 Manual de usuario

One Forall

One Forall URC-7140 Manual de usuario

One Forall

One Forall URC1913-2 Manual de usuario

One Forall

One Forall Xsight Touch Manual de usuario

One Forall

One Forall OARP05S Manual de usuario

One Forall

One Forall SimpleSet URC-7960 Manual de usuario

One Forall

One Forall URC-4110 Manual de usuario

One Forall

One Forall SMART STREAMER URC 7945 Manual de usuario

One Forall

One Forall OARN03S Manual de usuario

One Forall

One Forall URC-9910 Manual de usuario

One Forall

One Forall KAMELEON 3 URC-8203 Manual de usuario

One Forall

One Forall URC-3450 Manual de usuario

One Forall

One Forall URC6810 Manual de usuario

One Forall

One Forall Easy 2 Manual de usuario

One Forall

One Forall URC-7110 Manual sencillo

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación