Omron ZG2 Series Cómo utilizar
Smart Sensor
2-D Profile Measuring Sensor
ZG2
Short Manual
Setting tutorial
V1.0
ZG2 Short Manual
Overview
Extension cables:
ZG2-XC3CR: 3 m
ZG2-XC8CR: 8 m
ZG2-XC15CR: 15 m
ZG2-XC25CR: 25 m
Sensor heads:
ZG2-WDS70
ZG2-WDS22
ZG2-WDS8T
ZG2-WDS3VT
0.5m or 2m cable length
Data Storage Unit:
ZG2-DSU41
ZG2-DSU11
Sensor Controller:
ZG2-WDC41A
ZG2-WDC11A
Parallel Output Unit:
ZG-RPD41
ZG-RPD11
RS232 cable:
ZS-XPT2 for PLC
ZS-XRS2 for PC
PC Setup Software „SmartMonitor ZG2“
and USB cable included with the ZG-WDCxxA
Controller
Link:
ZS-XCN
RS232
Max. total length: 27m
RS232
Overview
ZG2 Short Manual
Overview
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11) (12)
(13)
(14)
(1) Judgement Indicator (turns on if judgement result is O.K.)
(2) Laser Indicator (turns on while the LASER is powered on)
(3) Zero Reset Indicator (turns on while Zero Reset function is active)
(4) Trigger Indicator (turns on while trigger input is active)
(5) LCD Screen (color graphic LCD)
(6) Menu Switch (selects standard or expert menu)
(7) Mode Switch (selects set or run mode)
(8) Control Keys
(9) Sensor Head Connector
(10) Extension Connector (connects multiple controllers)
(11) USB connector
(12) RS232 connector
(13) Voltage / Current selector (for linear output)
(14) I/O cable (voltage supply and I/O terminals)
Overview
ZG2 Short Manual
Overview
Overview
Overview
Up to 2 ZG-WDCxx can be connected together using a Controller Link Unit ZS-XCN
in order to perform calculations with 2 sensor heads. Optionally 1 Data Storage Unit
ZG2-DSU can be attached to the left side.
Channel assigment is always as shown above (regardless of the presence
of a ZG2-DSUxx).
The Data Storage Unit ZG2-DSUxx can be used for logging measurement results,
logging profiles or storing bank data.
ZG2 Short Manual
Optional:
ZG2-DSUxx ZG2-WDCxx Optional:
ZG2-WDCxx
CH0 CH1 CH2
If 2 ZG2-WDCxx are used,
connect the USB cable
only to CH2
ZS-XCN
Overview
ZG2 Short Manual
Tutorial
This chapter shows step by step how to set up the ZG2 profile sensor to perform a
measurement. Below you can find the 7 steps to follow. More detailed description of
each step is given then on the following pages.
1) Initialization (optional):
Initialize the sensor as a first step to start with default values.
2) Mount the sensor head:
Mount the sensor head that you can see the yellow profile line on the LCD screen.
3) „Teach“ a profile:
The stored profile is used for the setting of the measurement region and position
correction.
4) Select a measurement item:
The ZG2 has19 different measurement items and 1 calculation item for flexible
inspection of all kinds of measurements.The ZG2 can perform up to 8 tasks at the
same time without increase of measurement cycle time.
5) Set the measurement region for the measurement item:
The functioning of measurement items is based on characteristic points which are
defined by a horizontal or vertical regions along the profile line.
6) Optimize the image settings regarding cycle time and accuracy:
The ZG2 has multiple modes for the control of the laser power as well as multiple
filters for image improvement.
7) Setup position compensation (optional):
The ZG2 can compensate horizontal, vertical and slope postion variations.
Tutorial
Setting Tutorial
1) Initialization:
To operate the menu you can either use the cursor keys and the set key
or the number keys.
1) Move first the menu switch to „EXP“ and then the mode switch to „FUN“.
2) Press key „4“ to select the System menu.
3) Press key „2“ to select „INIT“.
4) Confirm „YES“ with key „1“. Wait until the init process is finished.
5) Set the mode switch back to „RUN“.
6) Confirm saving the settings with the key „1“.
After initialization the laser power mode is set to „Multi Mode“ (s. page xx) and
the measurement item for task 1 to „Height1“. On the LCD screen you can see
the profile in real time. The red cross and the value in the bottom line shows the
result of task 1. Pushing the orange „Menu“ key toggles the lcd screen
first to the measurement result screen and then to the cycle time display/
resp. the screen saver.
ZG2 Short Manual
MENU
/VIEW
ESC
ADJ
FUN RUNSTD EXP SET
1 2
3 4
LD ON ZERO TRIG
T1
T2
T3
T4
LV: 1-320
HEIGHT1 B1T1
3.000mm
1) Set to EXP 2) Set to FUN
Corsor keys
Number keys
1 - 4
Menu switch Mode switch
Tutorial
ZG2 Short Manual
2) Mount the sensor head:
The ZG2 can measure up to 8 tasks at the same time. The settings for these 8 tasks is
stored in 1 bank. Up to 32 banks can be stored in the ZG2-WDC. The bank can
be changed in run mode via digital input terminal, RS232 or USB.
Move the sensor head
until the profile can be
seen on the LCD screen
in „RUN“ mode.
The red cross and the
mm-value on the screen
represent the actual
result of task 1:
The average height of
the whole profile.
Example: Width measurement of a
bar of a workpiece:
LD ON ZERO TRIG
T1
T2
T3
T4
LV: 1-320
WIDTH2 B1T1
3.000mm
Tutorial
ZG2 Short Manual
3) Teach: Store a profile in the internal memory
Move the mode switch to the „FUN“ position, push key „1“ for „Meas“, and
again key „1“ for „TEACH“. Confirm the teach process with the key „1“ for „YES“.
The stored profile is used for setting the measurement region as well for the setting
of the position compensation in later steps. The tought profile is stored until the next
teaching, also if the sensor is powered down. After teaching 2 additional menu items
appear on the screen above:
• 3 SENS
• 4 CORECT
Remark:
In the menu „2 IMAGE“ you can find all settings regarding sensitivity and laser
intensity. For a first evaluation we can leave these settings unchanged. As a final
step the IMAGE settings can be optimized for tuning the measurement times to be
faster.
MENU
/VIEW
ESC
ADJ
FUN RUNSTD EXP SET
1 2
3 4
LD ON ZERO TRIG
T1
T2
T3
T4
MEAS
2 IMAGE
1 TEACH
„Meas“
„Teach“
Tutorial
4) Select a measurement item:
In order to choose the measurement item for task 1 for the measurement of the width
of the bar you have to select the menu „3 SENS“:
Push key „3“ for selection of menu „3 SENS“, now the screen for the task selection
appears. Here you can select one of the 8 tasks by pushing the corresponding
number key and/or using the cursor keys and pressing the „SET“ key. The
selected task also is also shown in the bottom line of the screen. At this moment task
1 is preset with the default measurement item „HEIGHT1“ from the initialization
at the beginning.
ZG2 Short Manual
LD ON ZERO TRIG
T1
T2
T3
T4
MEAS
2 IMAGE
1 TEACH
3 SENS 4 CORECT
„3 SENS“
Task 1
Tutorial
Otros manuales para ZG2 Series
3
Otros manuales de Accesorios de Omron
Omron
Omron CJ2*-CPU Series Manual de instrucciones
Omron
Omron ZFX-C10 COMMUNICATION Manual de funcionamiento
Omron
Omron E3X-MDA11 Manual de usuario
Omron
Omron F3S-TGR-CL_B Manual de usuario
Omron
Omron F250 - Manual de usuario
Omron
Omron ZN-DPS1- *** -S Series Manual de usuario
Omron
Omron ZS-HLDS3S Manual de usuario
Omron
Omron E2E - 2 Manual de usuario
Omron
Omron ZJ-SD Series Manual de usuario
Omron
Omron FQ - SHORTMANUAL V1 Manual de usuario
Omron
Omron E3S-C - Manual de usuario
Omron
Omron ES1B - DATASHEET 1 Manual de usuario
Omron
Omron ZX2-LDA41 Manual de usuario
Omron
Omron ZW-8000 Series Manual de usuario
Omron
Omron FZ4-6 series Manual de usuario
Omron
Omron F150-3 - Manual de instrucciones
Omron
Omron F3EM2-005 Series Manual de usuario
Omron
Omron SYSMAC CJ2H-CPU6@-EIP Manual de instrucciones
Omron
Omron Z4W-V Manual de usuario
Omron
Omron F500 - Manual de usuario
