Olympus R1018 series Manual de usuario
Quick Reference Guide
R1018 Series
© 2004 OLYMPUS TECHNOLOGIES SINGAPORE PTE
LTD. All rights reserved.
Olympus reserves the right to make changes to any
product to improve reliability, functionality or design.
Olympus does not assume any product liability arising
out of, or in connection with, the application or use of any
product, circuit, or application described herein.
No license is granted, either expressly or by implication,
estoppel, or otherwise under any patent right or patent,
covering or relating to any combination, system,
apparatus, machine, material, method, or process in
which Olympus products might be used. An implied
license only exists for equipment, circuits and
subsystems contained in Olympus products.
Olympus and the Olympus logo are registered
trademarks of Olympus Technologies Singapore Pte Ltd.
Other product names mentioned in this manual may be
trademarks or registered trademarks of their respective
companies and are hereby acknowledged.
Olympus Technologies Singapore Pte Ltd
41 Science Park Road #04-17/18 The Gemini
Singapore Science Park 2, Singapore 117610
www.olympus-ost.com
Patents
This product is covered by one or more of the following
Singapore or foreign Patents and Registered Designs:
Singapore Patent No. 200401460-1
Singapore Registered Design No. D2003/1055/C
1
Table of Content
Introduction
Model Configuration ........................................ 3
Accessories .................................................... 3
Parts of the R1018 series ............................... 4
Getting Started
Charging the Battery ....................................... 5
Starting the R1018 ......................................... 5
Aligning the Screen ......................................... 6
Using the Keypad and the Side Button ........... 7
Using the Stylus .............................................. 8
Initiating the Screen ....................................... 9
Input Methods ............................................... 10
Turn on and off the Backlights ...................... 10
Using the Headset ........................................ 10
Resetting Your R1018 Terminal
Performing a Soft Rest ................................. 11
Performing a Hard Rest ................................ 11
Host Communications
Using the USB Sync Cable ........................... 13
Using wireless communications
Establishing Active Sync via IrDA ................. 14
Browsing Internet via IrDA ............................ 14
Establishing Active Sync via Bluetooth ......... 15
Connecting to the GPRS mobile phone
via Bluetooth ................................................. 15
Connecting to the Bluetooth access point .... 18
Browsing Internet via WiFi ............................ 19
2
Using Online Help ....................................... 22
Maintaining the R1018 ................................ 23
Troubleshooting ......................................... 24
Regulatory and Warning Information ....... 28
Service Information .................................... 33
Introduction
Thank you for your purchase of R1018 terminal.
This guide describes how to set up and use the
terminal. The term R1018 refers to the entire
batch.
Model Configuration
R1018-xx20-yyy-zz: This is a basic handy
terminal of the series with color display, WiFi and
Bluetooth radio function.
Note: “xx” shows memory configuration and
“yyy” shows software configuration. (“zz” is for
optional.)
Accessories
Each R1018 operates on a 1500 mAh Lithium
Polymer built-in battery. The following are the
accessories included together with your
purchase:
•AC Adapter
•USB Sync Cable
•Stylus
AC Adapter USB Sync Cable Stylus
3
Parts of the R1018 Series
LCD Display
LED
Mic
Keypad
Communication Port
Audio
Connector
Side Button
Reset Switch
IrDA Port
Speaker
Stylus
4
5
Getting Started
Before you can use your R1018, perform these
basic setup procedures:
•Charge the battery
•Start the R1018
Charging the Battery
Before using your R1018 for the first time, charge
the built-in Lithium-Polymer battery for about 3
hours using the USB Sync Cable with AC
Adapter attached. Follow these same procedures
to recharge the battery.
When the battery is fully used up, charge within
72 hours to prevent any data loss.
•Connect the AC Adapter to the USB Sync
Cable.
•Insert the USB Sync Cable to the
Communication Port found at the bottom of
the R1018.
•Plug the AC Adapter into a wall outlet and
turn on a wall outlet, if applicable.
•The Terminal Status LED turns RED to
indicate charging.
•The LED will turn GREEN after the battery is
fully charged. This will take approximately 3
hours.
Starting the R1018
Press the Power Button to turn the R1018 on or
standby. In case where the Power Button is
pressed for the first time, the booting splash
screen will be displayed for about 30 seconds.
Aligning the Screen
Remove the Stylus from its storage silo on the
back of the R1018. To align your R1018, the
cursor on the touch screen needs to be aligned
with the tip of your Stylus.
•Tap and hold the center of each target that
appears on the screen with the tip of the
Stylus.
•Tap anywhere on the screen to finish to the
setting.
Press & hold stylus on the center
of the target. Repeat as the target
moves around the screen.
+
Target
Note: The process will repeat if it detects an
inaccuracy. These screens also appear every
time you perform a hard reset.
6
Using the Keypad and Side Button
Power Enter
Cursor
F3
F2
F1
F4
Key Action
Power Press Power to either set the
R1018 to standby or ON
mode.
F1 Press F1 to start Word Pad.
F2 Press F2 to start Internet
Explorer.
F3 Press F3 to start Media
Player.
F4 Press F4 to display Inbox.
F2+F4 Enable Wireless LAN.
Enter Press Enter after entering data
or a command.
Cursor Press cursor keys to move the
cursor left, right, up and down
on the screen.
Side
Button Press Side Button to launch
Bluetooth application.
7
8
Using the Stylus
The Stylus selects items and enters information.
The Stylus functions as a mouse.
•Tap: Touch the screen once with the Stylus
to select an item or option.
•Double-Tap: Touch the screen twice with the
Stylus to open an item.
•Drag: Hold the Stylus on the screen and drag
across the screen to select text and
messages. Drag in a list to select multiple
items.
•Tap-and-Hold: Tap and hold the Stylus on an
item to see the available actions.
Tabla de contenidos
Otros manuales de PDA de Olympus
