Olympus U-CBS Manual de usuario
Notes
This instruction manual is for the coded function system.
To ensure the safety, obtain optimum performance and to familiarize yourself fully with the use
of this product, we recommend that you study this manual thoroughly before operating this
product, and always keep this manual at hand when operating this product.
Retain this instruction manual in an easily accessible place near the work desk for future
reference.
For details of products included in the configuration of this system, see page 4.
Instructions
Coded function system
Optical Microscope Accessory
In accordance with European Directive on Waste Electrical and Electronic Equipment, this
symbol indicates that the product must not be disposed of as unsorted municipal waste, but
should be collected separately.
Refer to your local Olympus distributor in EU for return and/or collection systems available in
your country.
This product is applied with the requirements of standard IEC/EN61326-1 concerning
electromagnetic compatibility.
- Immunity Applied to industrial and basic environment requirements.
For Korea only
이 기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서
가정용 환경에서 사용하는 경우 전파간섭의 우려가 있습니다.
IMPORTANT -Be sure to read this section for safe use of the equipment.-................. 1
1 Nomenclature of each part............................................................................................................ 3
2 System diagram....................................................................................................................................... 4
3 Layout of the cables............................................................................................................................. 6
1Combining with the microscope frame (BX53F2) and U-IFRES..........................................................7
2Combining with the microscope frame (BX43F) and U-IFRES.............................................................8
3Combining with the microscope frame (BX43F)...............................................................................................9
4 Information readout / External transmission ...............................................................10
5 Specifications...........................................................................................................................................12
Contents
1
Coded function system
IMPORTANT -Be sure to read this section for safe use of the equipment.-
This system enables to read out the information from the coded illuminator and the coded revolving nosepiece and to
transmit the information externally.
Safety precautions
The following symbols are placed on this product.
Study the meaning of the symbols and always use the product in the safest possible manner.
Symbol Meaning
Indicates a non-specific general hazard. Follow the description given after this symbol or
in the instruction manual.
Indicates that the main switch is ON.
Indicates that the main switch is OFF.
Safety symbols
·Before connecting the cables, be sure to set the POWER switch of the control box for coded function
(U-CBS) to OFF (out position).
·For safety, always use the provided AC adapter only.
·Keep the cables away from the lamp housings (halogen bulb, etc.) that become hot and the surroundings.
Otherwise, the cables may melt and cause an electric shock hazard.
·Never apply an excess force to cables, such as to stretch cables. Otherwise, they may be damaged.
Coded function system
2
·This product is a precision instrument. Handle it with care and connect cables gently to avoid
subjecting it to sudden or severe impact. Also, this product is not waterproof.
·Do not use the product in areas where it may be subjected to direct sunlight, high temperature and/or
humidity, dust or vibrations.
(For conditions of operating environments, see “5 Specifications“ on page 12.)
·Never connect or disconnect the cable while the POWER switch of the control box is set to ON
(depressed position). Otherwise, malfunction may result.
·Never disassemble any part of the product. Otherwise, failure may result.
·Before disposing of this product, be sure to follow the regulations and rules of your local government.
Contact Olympus for any questions.
CAUTION
2Handling Precautions
1Cautions
If the product is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition, the
product may also be damaged. Always use the product according to this instruction manual.
The following symbols are used in this instruction manual.
CAUTION
: Indicates a potentially hazardous situation which, if not avoided, may result in
damage to the equipment or other property.
TIP
: Indicates the useful knowledge or information for use.
3
Coded function system
1Nomenclature of each part
Control box for coded function
U-CBS
Microscope frame hanger (top)
Connector for hand switch
For external EXPOSE button of
microscope digital camera
Connector for BX3-CBM
Connector for AC adapter
RS-232C connector
Connector for coded revolving nosepiece
Connector for coded illuminator
POWER switch
ON: Depressed position
OFF: Out position
Microscope frame hanger (bottom)
Coded function system
4
2 System diagram
Coded illuminator
Control box for coded functionNote 3)
U-CBS
Microscope
frame
·The connectors of U-CBS are equipped with dust covers. Remove the dust covers only from the
connectors you want to connect cables.
·Be sure to connect only the units specified by Olympus to the connecters of U-CBS.
If a non-specified unit is connected, the performance of the entire system cannot be guaranteed.
·Before connecting the cables, be sure to set the POWER switch of U-CBS to OFF (out position).
Insert the cables securely to connectors paying attention to their shapes. If the connector is provided
with clamping screws, be sure to tighten them.
·If you insert a non-specified connector into the connector of U-CBS, the connector may be damaged.
CAUTION
· PC
· Microscope digital cameraNote 4)
Cable for coded illuminator Note 2)
RS-232C cableNote 1)
AC adapter
Cable for interface for coded nosepieceNote 2)
Interface for coded nosepiece
U-IFRES
Hand switch
U-HSEXP
Control box
BX3-CBM
Coded revolving
nosepiece
Interface for coded nosepiece
Interface for coded nosepiece
U-IFRES
U-IFRES
Cable for revolving
nosepiece
Hand switch
U-HSEXP
Control box
BX3-CBM
Control box
BX3-CBM
AC adapter
Interface cable
CBSIFCBL200
5
Coded function system
Note 1)
RS-232C cable specifications
D-sub 9-pin (F) D-sub 9-pin (F)
a
d
c
Note 2)
Align the mark aon the connector of the coded illuminator with
the mark aof U-CBS and attach the coded illuminator. When
attaching U-IFRES or the coded revolving nosepiece, align marks
bin the same manner.
Note 3)
Hang U-CBS con the hangers don the back side of the
microscope frame.
Note 4)
When connecting the microscope digital camera to U-CBS to use
U-CBS, the order to turn ON the power is: 1POWER switch of
U-CBS and 2Switch of the microscope digital camera. If the
switches are set to ON in the different order, the microscope digital
camera cannot recognize U-CBS.
Also, if the connector of the coded revolving nosepiece are not
connected to U-CBS, U-CBS does not recognize the coded
revolving nosepiece. So be careful.
b
Coded function system
6
3Layout of the cables
The cables of units can be laid out easily by attaching the cable holders on the back side of the microscope frame.
The cable holders are provided with following units.
· Control box for coded function (U-CBS): 6 pieces
· Coded revolving nosepiece: 2 pieces
On page 7 and after, the positions to attach cable holders and the cable layout are described for each microscope frame.
· The number of cable holders to be used differs depending on the units combined with the microscope frame.
· If the cable holder positions are significantly deviated, the cable may not reach the connector. Attach the cable
holders while making sure that the cable reaches the connector.
· Make sure that cable holders are not deflected and close the cable holders.
TIP
7
Coded function system
About 69 mm
* :In case of laid out the cable for hand switch on the left side as shown above picture
**:In case of laid out the cable for hand switch on the right side as shown above picture
For procedures to attach the hand switch to microscope frame, see page 11.
TIP
Hand switch**
Cable holder**
Velcro tape
RS-232C cable
Coded illuminator
(provided with hand switch)
About 78 mm
AC adapter
Cable holder*
Hand switch*
About 85 mm
Cable holder*
Align with the upper left
corner of the label.
Coded revolving nosepiece
U-IFRES
1Combining with the microscope frame (BX53F2) and U-IFRES
Align with the height of
the edge between the
back side and under
side on the microscope
frame.
back side and under
side on the microscope
frame.
Tabla de contenidos
Otros manuales de Microscopio de Olympus
Olympus
Olympus CX40 Manual de usuario
Olympus
Olympus BH2 Series Instrucciones de funcionamiento
Olympus
Olympus SZX16 Manual de usuario
Olympus
Olympus BH2 Series Manual de usuario
Olympus
Olympus SZX16 Manual de usuario
Olympus
Olympus DSX1000 Manual de usuario
Olympus
Olympus X-Tr Instrucciones de funcionamiento
Olympus
Olympus CX31 Manual de usuario
Olympus
Olympus BXFM Manual de usuario
Olympus
Olympus CX33 Manual de usuario
Olympus
Olympus SZX9 Manual de usuario
Olympus
Olympus CKX53 Manual de usuario
Olympus
Olympus BX63 Manual de usuario
Olympus
Olympus SZX7 Manual de usuario
Olympus
Olympus CX31-P Manual de usuario
Olympus
Olympus VANOX Manual de usuario
Olympus
Olympus CK40M FRAME Instrucciones de funcionamiento
Olympus
Olympus POS Manual de usuario
Olympus
Olympus KHC Manual de usuario
Olympus
Olympus CH10 Instrucciones de funcionamiento
