Olivetti D-COLOR MF554 Manual de usuario

E-1

Be sure to correctly follow the procedures in order as explained in this Installation Manual.

If you do not follow the procedure in order, the image trouble may occur.

1. Outline of installation procedures

When installing the main body and associated options as a system, follow the order shown on the upper.

Caution:

• Lifting the main body in an awkward position or transporting it in a poorly balanced position could result in

personal injury. When transporting the main body, assign an adequate number of persons to the job and

ensure that each person can take a good position of not being excessively loaded.

(mass: approx. 110 kg (242-1/2 lb))

Note:

• For the detailed installation procedures for each option, follow the instructions given in the corresponding

installation manual and perform the procedures correctly.

• When placing the main body on the floor, make sure to use the paper feed cabinet or the desk to secure

the performance and the quality of the product.

• Once the Power Switch is turned ON, do not turn OFF it until the installation work has been completed.

Machine

Electronic system options

AU-102

AU-201S

PC-215 PC-415 DK-510 DK-705PC-115

FK-514

FK-515*

UK-212*

SC-508*

KP-101

WT-506

MK-735

HD-524*

HT-509

TK-101

KH-102 EK-608*

EK-609*

MK-730

MK-742*

MK-734

CU-102

LU-302

LU-207

VI-510IC-416

SP-501

UK-501

OT-506 RU-513

PK-520

FS-537FS-536 FS-537SDFS-536SD

JS-602PI-507

PK-523

ZU-609

PK-519*

FS-533*

JS-506*

Electronic system options

*1: No particular order in

installation procedures.

*2: Varies depending on the

applicable marketing area

3: MF554/MF454 only

d-Color MF654/MF554/MF454

INSTALLATION MANUAL

©Olivetti S.p.A Applied Machines: d-Color MF654/MF554/MF454

Y118120-9 Installation Manual

E-2

2. Installation space (unit: mm (inch))

d-Color MF654 + PC-215 + FS-537SD + LU-207

3. Pre-installation check items

(1) Select a level and stable place for installing the

machine.

(2) Be sure to use a power source of the voltage and

frequency indicated in the product specifications.

Ensure that the current carrying capacity of the

power outlet is at least equal to the current listed

in the product specifications.

(3) Power the machine directly from a dedicated

power outlet. (Do not use an extension cord.)

(4) Do not plug or unplug the power cord with wet or

dirty hands, otherwise you may get an electric

shock.

(5) Avoid a hot and humid environment, or a place

exposed to direct sunlight.

(6) Avoid a dusty location, or a place near volatile

and flammable substances.

(7) Avoid a poorly ventilated place.

4. Notes on using touch panel

Be sure to instruct users on the following points.

• This machine uses a capacitive touch panel.

When you touch the touch panel, use your fin-

ger or the stylus pen supplied with the machine.

If you touch the panel using your nail or a pen

tip instead of using your finger or the stylus pen,

the touch panel does not respond normally.

• Pressing the touch panel hard may cause dam-

age.

• Do not strongly press the panel or press it using

the sharp tip of mechanical pencils.

• The key is a finger tapping (quick light touch

using a finger) operation.

5. Accessory parts

* Varies depending on the applicable marketing

area.

1244

(49)

452

(17-13/16)

2477

(97-1/2)

781

(30-3/4)

1267

(49-7/8)

1560.5

(61-7/16)

353.5

(13-15/16)

953

(37-1/2)

254

(10)

847

(33-3/8)

420

(16-9/16)

No. Name Q’ty

1. User’s guide holder 1

2. Quick start guide 1

3. Installation manual 1 set

4. User’s guide CD 1

5. CD-ROM 1 set

6. Paper size label 1

7. Panel sheet 1

8. Chart 1

9. Cap A (Black) 2

10. Cap B (White) 2

11. Connector cover 1

12. Duct cover 1

13. Cord clamp A *

14. Cord clamp B

15. Screw A

(3 x 8 mm) 1

16. Screw B

(3 x 8 mm) 2

17. Screw C

(3 x 30 mm) * 1

18. Stylus pen 1

19. Waste toner box 1

Installation Manual Y118120-9

E-3

Note:

• Keep the paper size label at hand. It is neces-

sary for mounting the Large Capacity Unit LU-

302.

• Keep the cord clamp B at hand. It is necessary

for mounting the Upgrade Kit UK-212, Authenti-

cation Unit AU-201S, or Authentication Unit

AU-102.

*Power supply:

d-Color MF654: 120V 16A, 220-240V 10A d-

Color MF554/MF454: 120V 12A, 220-240V 9A

Note:

This manual provides the illustrations of the acces-

sory parts and machine that may be slightly differ-

ent in shape from yours. In that case, instead of

the illustrations, use the appearance of your

machine to follow the installation procedure. This

does not cause any significant change or problem

with the procedure.

6. Installing the main body and the Paper

Feed Cabinet (or the Desk)

(1) Take the main body and the Paper Feed Cabinet

(or the Desk) out from its packaging.

Caution:

Main body mass: approx. 110 kg/242-1/2 lb

• Make available collective manpower of an

appropriate size for transporting the main body.

Note:

• Remove the machine, holding it by the handles

on the right and left sides as shown in the illus-

tration and keeping it level.

(2) Refer to the installation manual for the Paper

Feed Cabinet (or the Desk) and follow the

“Installation Procedures.”

Note:

If installing either the Heater HT-509, the Trans-

former kit TK-101, or the Power Supply BOX MK-

734, install them at the same time as the installa-

tion of the Paper Feed Cabinet (or the Desk).

Keep this bag away from babies and

children. Do not use in cribs, beds,

carriages, or playpens.

The thin film may cling to nose and

mouth and prevent breathing. This bag is

not a toy.

If a power cord is not supplied, use only

the power cord that meets the following

conditions.

Failure to do this could result in a fire or

electrical shock.

• The power cord has voltage and current rating

appropriate for the rating plate on this machine.

• The power cord meets regulatory requirements

for the area.

• The power cord is provided with grounding

pin/terminal.

When holding the transportation handles,

be careful not to catch your fingers in the

machine.

Y118120-9 Installation Manual

E-4

7. Removing protective tape, packing and

other shipping materials

(1) Remove the protective tape and the protective

materials.

Note:

Be sure to lock the lever after removing the protec-

tive tape A.

(2) Open the right door and remove the protective

sheet and locking materials.

Note:

• After removing the locking materials, make sure

that the transfer roller assy is secured in place.

In the case of <NG>, press the transfer roller

assy into place so that it is secured as shown in

<OK>.

• Save the packaging materials removed in this

and subsequent steps of (6), (8), and (14) for

later use when transporting the machine.

(3) Close the right door.

(4) Slide out the tray 1.

(5) Remove the protective tapes from the inside of

the tray 1 and remove accessory parts.

Note:

See the User's Guide CD for instructions on set-

ting paper in each tray and configuring the paper

types.

< OK > < NG >

Installation Manual Y118120-9

E-5

(6) Slide out the tray 2 and remove the tray locking

materials.

(7) Remove the protective tapes from the inside of

the tray 2 and remove accessory parts.

(8) Remove the locking screws.

(9) Attach the supplied caps A and B.

(10) Remove the protective sheets.

(11) Open the lower front door.

(12) Remove the protective tape.

Protective tape

Y118120-9 Installation Manual

E-6

(13) Remove the protective tape from the develop-

ing units.

Note:

Do not remove the tape A in this procedure.

(14) Remove the locking materials from the four

places.

(15) Release the lever of the drum unit (K).

(16) Slightly slide the drum unit (K) out and remove

the protective tape.

(17) Slide the drum unit (K) into the machine.

(18) Lock the drum unit (K) with the lever.

(19) Install the supplied waste toner box.

Note:

Push the areas indicated by the “ ” marks to set

the waste toner box to the machine.

(20) Close the lower front door.

Installation Manual Y118120-9

E-7

8. Installing the toner cartridge

Note:

Since cartridge is not supplied with the machine,

purchase toner cartridge (of different colors) sepa-

rately.

(1) Shake the toner cartridge up and down and left

to right 5 to 10 times respectively.

Note:

Shake the cartridge adequately. Otherwise, it may

cause trouble.

(2) Open the upper front door.

(3) Insert the toner cartridge into the machine.

Note:

• Make sure that the color is same between

inserting port and the toner cartridge.

• Make sure that the blue label position of the

toner cartridge is matched with the one of the

machine side.

(4) Push the toner cartridge all the way in and rotate

it clockwise to lock it.

Note:

Make sure that the toner cartridge is pushed all the

way in.

(5) Using the same procedure, install the toner car-

tridges for other colors of toner.

(6) Close the upper front door.

9. Installing other options

To install other options, refer to the installation man-

ual for each option and follow the “Installation Proce-

dures.”

10. Mounting the accessory parts

(1) Remove the protective cover from the supplied

stylus pen.

Note:

Discard the removed protective cover.

Y118120-9 Installation Manual

E-8

(2) Set the stylus pen in the place shown in the illus-

tration.

(3) Attach the supplied connector cover to the

machine. (One supplied screw A)

(4) Attach the supplied duct cover.

(Two supplied screws B)

11. Connecting the power cord

Note:

Steps (1) and (2) may be unnecessary depending

on the applicable marketing area.

(1) Connect the power cord.

(2) Fit the supplied cord clamp A over the power

cord. (One supplied screw C)

(3) Plug the power cord into the power outlet.

Tab

Use the appropriate power cord.

Failure to do this could result in a fire or

electrical shock.

Installation Manual Y118120-9

E-9

12. Starting the machine

Open the lower front door and turn ON the power

switch, then close the lower front door.

13. Date & Time Setting/Time Zone Setting

(Service Mode)

(1) Display the Service Mode screen.

(For details of how to display the Service Mode

screen, see the service manual.)

(2) Display the Date & Time Setting/Time Zone Set-

ting screen.

(To display the Date & Time Setting/Time Zone

Setting screen, press Stop → 3 on the control

panel.)

(3) Do not input date and time but touch “Entry” of

the Date & Time Setting.

(4) Input the time zone using up/down keys or direct

keys.

(5) Touch “Entry” of the Time Zone Setting.

(6) Touch “Apply.”

(7) Touch “OK.”

(8) Touch “Next.”

14. Serial number input

Note:

Serial number input is, if necessary, needed only

for the optional devices installed in “9. Installing

other options.”

(1) Touch the item you want to enter and input the

serial number.

(2) Touch “END.”

(3) For other devices, enter their serial number in

the same way.

(4) Touch “END.”

(5) Touch “Next.”

15. Unit change

Note:

This function allows the user to select the type of

message that will appear when the replacement

time arrives for each of the different units.

(1) Select the appropriate message type for each

unit.

(2) Touch “Service.”

16. Performing Non-Image Area Erase

Check

Note:

Perform the below at the site where customer

uses the machine.

(1) Select the Non-Image Area Erase Check func-

tion as follows:

Machine → Non-Image Area Erase Check.

(2) Open fully the dual scan document feeder, the

reverse automatic document feeder, or the origi-

nal cover if loaded.

Note:

• Do NOT place a document on the document

glass.

• Clean the document glass if dirty.

(3) Press the Start key.

(4) Make sure that “Result” is “OK.”

Note:

If “Result” is “NG1” or “NG2”, review the place and

direction of installation, or take measures to block

the light source (by covering it, etc.), then perform

installation checking again.

(If a fluorescent light or other bright light sources

exist right above the machine, the light source can

hinder installation checking and cause operation

errors in the Non-Image Area Erase Check. For

detailed information, see the service manual.)

(5) Touch “OK.”

Y118120-9 Installation Manual

E-10

17. Configuring other options

(1) If any of the following options are installed, refer

to the “Configuration procedures” of the installa-

tion manual for each option and configure the

option(s).

• Paper Feed Cabinet PC-415

• Large Capacity Unit LU-207/LU-302

• Stamp Unit SP-501

• Double feed detection Kit UK-501

• Punch Kit PK-523/PK-520/PK-519

• Z Folding Unit ZU-609

• Fax Kit FK-515/FK-514

• Local Interface Kit EK-609

• Security Kit SC-508

• Authentication Unit AU-201S/AU-102

• Upgrade Kit UK-212

• Hard Disk HD-524

• Clean Unit CU-102

•Network Fax

(2) Exit from the Service Mode and return to the ini-

tial screen.

18. Connecting the network cable

(1) Connect the main body and networking equip-

ment (HUB) using the network cable.

Note:

The following shows the recommended network

cables that correspond to each communication

speed.

• 10BaseT/100BaseTX: Category 5

• 1000BaseT: Category 5E, Category 6

(2) Check LEDs for lighting conditions.

LED1:

Should light up steadily if the link network con-

nection has been made.

LED2:

Should blink according to the communications

status of the ACT network.

(3) Route the network cable.

<When adding no paper feed options/desk or when

using the Desk DK-705>

a) Route the network cable through the harness

guide and pass it through the notch.

Note:

Leave an appropriate amount of slack in the por-

tion of the cable between the plug and the harness

guide in a manner which does not interfere with

the opening and closing of the cover.

<When using the Paper Feed Cabinet PC-415/PC-

215/PC-115 or the Desk DK-510>

a) Remove the rear right cover from the paper

feed cabinet or the desk. (Two screws)

b) Remove the knockout from the rear right cover

using nippers.

Networkport

LED2

LED1

Leave an appropriate amount of slack.

Installation Manual Y118120-9

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora todo en uno de Olivetti

Olivetti

Olivetti d-Color MF2604 Manual de usuario

Olivetti

Olivetti d-COLOR MF652 Manual de usuario

Olivetti

Olivetti d-COPIA 3004MF Manual de usuario

Olivetti

Olivetti d-COPIA 1801 MF Manual de usuario

Olivetti

Olivetti d-COPIA3003MF Manual de usuario

Olivetti

Olivetti d-COPIA4513MF plus Manual de usuario

Olivetti

Olivetti d-COLOR MF652 Manual de usuario

Olivetti

Olivetti SIMPLE_WAY Manual de usuario

Olivetti

Olivetti d-COLOR MF652 Instrucciones de instalación y mantenimiento

Olivetti

Olivetti d-Color MF450 Manual de usuario

Olivetti

Olivetti d-Color MF759 Manual de usuario

Olivetti

Olivetti d-Copia 16W Manual de usuario

Olivetti

Olivetti d-COLOR MF652 Manual de usuario

Olivetti

Olivetti d-Color MF2001 Manual de usuario

Olivetti

Olivetti d-COLOR MF3300 Manual de usuario

Olivetti

Olivetti d-COLOR MF3300 Manual de usuario

Olivetti

Olivetti d-COLOR MF3300 Manual de funcionamiento

Olivetti

Olivetti d-Color MF2001 Manual de usuario

Olivetti

Olivetti d-COPIA 3500MF Manual de usuario

Olivetti

Olivetti d-Color MF1600 Manual de usuario

Olivetti

Olivetti d-color MF551 Manual de servicio

Olivetti

Olivetti d-Copia 1801MF Plus Manual de usuario

Olivetti

Olivetti d-COLOR MF3800 Manual de usuario

Olivetti

Olivetti d-COLOR MF652 Manual de usuario

Manuales populares de Impresora todo en uno de otras marcas

Triumph Adler

Triumph Adler DC 2016 Manual

Epson

Epson WorkForce WF-2510 Guía del usuario

Epson

Epson Stylus Scan 2000 Manual de instalación y operación

Epson

Epson PictureMate Snap PM 240 Manual de instrucciones

Konica Minolta

Konica Minolta bizhub C35 Manual de usuario

Brother

Brother MFC-J430w Manual de usuario

Konica Minolta

Konica Minolta BIZHUB 558 Manual de usuario

Lexmark

Lexmark MX710 Series Manual

Brother

Brother MFC-9760 Manual de usuario

Lexmark

Lexmark XC8155 Manual de usuario

Lexmark

Lexmark X642E Manual de usuario

Sharp

Sharp MX-2310U Guía

Aficio

Aficio 200 Manual de usuario

Canon

Canon ImageCLASS 2300 Manual

Ricoh

Ricoh Pro C900 Manual de usuario

Lexmark

Lexmark X925 Manual de usuario

Brother

Brother Business Smart MFC-J4510dw Manual de usuario

Epson

Epson Stylus CX8400 Series Manual de usuario

Olivetti d-COLOR MF554 Manual de usuario

Manuales populares de Impresora todo en uno de otras marcas