Olimpia splendid secco tech Manual de usuario
TECHNICAL FEATURES
Secco Tech
Power Supply 230V - 50Hz
Input Power (27°C - 65% U.R.) 190 W – 1,2 A
Max Input Power (32°C - 80% U.R.) 232 W – 1,3A
Heating Element Input power --
Dehumidification Capacity 27°C - 65% U.R. (liters) 6,6 /24 h
Dehumidification Capacity 32°C - 80% U.R. (liters) 13 /24 h
Fan Speeds 1
Refrigerant type R 134A
Refrigerant quantity 0,160 kg
Air Flow 120 m
3
/h
Tank Capacity (liters) 2
Dimensions (HxWxD) mm 300X427X258
Weight 13 kg
Noise level (sound power) 36 dB(A)
Water Proof Level IPX0
OPERATING WORKING LIMITS
Max working conditions in dehumidification mode: DB / WB 35°C/31°C
Min working conditions in dehumidification mode: DB / WB 2°C/1°C
INTRODUCTION
The dehumidifier is fitted with an electronic logic system which controls operation and optimises consumption and performance.
The keys and information on the control panel have the following meanings
1) Start / Stand-by key
2) Operating mode selection key
3) Desired humidity / increment key (selection range from 30 to 90%).
4) Desired humidity / decrement key (selection range from 30 to 90%).
5) Detected ambient humidity / temperature warning key
6) Temperature indication
7) Humidity indication
8) Operating mode indications
9) Condensate collection tank full or tank shortage (LED ON),
Continuous discharge function enabled (LED BLINKING with frequency 1.25Hz).
Tank empty/present with continuous discharge disabled (LED OFF).
SELECTING FUNCTIONS
Stand-by. Key (1)
This key activates the dehumidifier or puts it in Stand-by mode. In the latter case, the display shows ' - - - - ' and the dehumidifier is
deactivated.
Mode. Key (2)
Pressing this button the following operating modes can be set:
• DEHUMIDIFICATION, indicated by the "drop" symbol light on the display.
• DRYING
,
indicated by the "T-Shirt" + “HI” symbols light on the display.
OPERATION WITH CONTINUOUS DISCHARGE
To operate the dehumidifier with continuous discharge, carry out the following operations:
• Take the tank out of the appliance.
• Connect the rubber pipe provided in the outfit to the condensate collection tank (at the top of the tank compartment).
• Secure the pipe with the metal clamp provided.
• Simultaneously press the increment (3) and decrement (4) keys for three seconds, with the machine in function
The activation of this function is indicated by the flashing "tank" symbol (9).
The continuous discharge function is cancelled if the empty tank is refitted.
FUNCTION DETAILS
• DEHUMIDIFICATION indicated by the "drop" symbol light on the display.
Compressor and fan are switched on if the minimum OFF time (Cf) has elapsed and if the relative humidity
value is higher than the set point + 3; compressor and fan remain ON as long as the relative humidity value is
above the set point – 3; when below the set point – 3, compressor and fan switch off (the fan switch-off is
delayed by 30 seconds with respect to the compressor) and remain off for a minimum time equal to Cf (measured as from switch-
off of the compressor), at the end of which compressor and fan are switched back on again if the relative humidity value is greater
than the set point +3.
The set point can be adjusted from 30% to 90% Rh in steps of 5%; pressing the UP (Key 3) or DOWN (Key 4) keys increases or
decreases the set point value by 5%.
•
DRYING MODE
Compressor and fan are switched on if the minimum OFF time (Cf) has elapsed.
Compressor and fan switch off only in the following cases:
cut in of the tank full switch,
operation in defrosting mode,
alarms (the switching off of fan always delays for 30 seconds compared with compressor.
The fan speed is always the minimum speed (winding no. 1 is energized).
• DEFROSTING MODE
If there is a frost condition (evaporator temperature < Ft and compressor ON) the compressor remains on for
a maximum time equal to Co minutes, at the expiry of which air defrosting takes place (fan on at minimum
speed, resistor not active in models with resistor, compressor off) which terminates when the pre-set
temperature is reached (evaporator temperature > St), compatibly with the minimum compressor OFF
duration Cf.
If the formation of frost is detected and the compressor is stopped due to reaching of the set point before the
expiry of Co the fan remains on until the end of defrosting temperature is reached.
ALARM CODES
Display
Indication Likely Cause Suggested Solution
Relative humidity drops below very low values (<22%). Activate the dehumidifier with
higher ambient
humidity conditions.
"Hr" flashing
Humidity sensor broken. Change humidity sensor or
whole PCB (according to the
model).
"tE" flashing The ambient evaporator temperature sensor
is damaged. Change ambient temperature
sensor or whole PCB (according
to the model).
"Lo" flashing The ambient temperature is too low. It means that
after 30
minutes of operation in defrosting mode (compressor
stopped and fan working) the defrosting temperature does
not exceed St. Alarm reset automatically after room temp
rise up St.
Activate the dehumidifier with
higher ambient humidity
conditions.
"EE" flashing The EEPROM of the PCB is damaged. Change the PCB (for some
model models only).
Mnemonic Range scheduled Parameters set Description
Co 20 min 50 min 20 Compressor in defrosting ON time
Cf 3 min 15 min 3 Compressor minimum OFF time
Ft -9°C +9°C 1 Frost accumulation temperature
St 0°C +9°C 3 End of defrosting temperature
• AUTOTEST MODE
By pressing the keys 4+5 for 3 seconds in sequence with the unit in Stand-by, the following
sequence is started (each phase has a duration of 3 seconds):
- switch-on of all symbols of the displays
- display of the software release
- activation of the fan (max speed managed according to the model, resistor powered when provided) and
compressor, displaying the code At on digits to the right side and the evaporator probe temperature
to the left side.
The compressor remains ON continuously, independently of the set point and the tank level switch; the
pause between stop and subsequent start and the defrosting function are also excluded.
The tank level symbol is active if the tank is absent (switch open), off if the tank is present (input closed).
Pressing the key 5 the software refresh the standard display mode as room air temperature and relative humidity values.
Press the stand-by key or disconnect the power supply to quit the auto test mode.
SECCO TECH WIRING DIAGRAM
A1 - Power board
A2 - Control board
A3 - Humidity/temperature sensor board
B1 - Evaporator temperature probe
F1 - Overload protector
M1 - Compressor
M2 - Fan motor
S1 - Microswitch
Tabla de contenidos
Otros manuales de Deshumidificador de Olimpia splendid
Olimpia splendid
Olimpia splendid AQUARIA 10 Guía de inicio rápido
Olimpia splendid
Olimpia splendid AQUARIA 14P Manual de lista de piezas
Olimpia splendid
Olimpia splendid SeccoReale Elettronico Manual de lista de piezas
Olimpia splendid
Olimpia splendid AQUARIA SILENT Guía de inicio rápido
Olimpia splendid
Olimpia splendid Secco Asciutto EL Manual de lista de piezas
Olimpia splendid
Olimpia splendid Secco Manual de lista de piezas
Olimpia splendid
Olimpia splendid SeccoReale Manual de lista de piezas
Olimpia splendid
Olimpia splendid SeccoMust Manual de lista de piezas
Olimpia splendid
Olimpia splendid AQUARIA SLIM 14 P Manual de lista de piezas
Olimpia splendid
Olimpia splendid AQUARIA SILENT 15 P Manual de lista de piezas
Olimpia splendid
Olimpia splendid seccoprof Manual de lista de piezas
Olimpia splendid
Olimpia splendid SECCOPROF 30 P Manual de lista de piezas
Olimpia splendid
Olimpia splendid AQUARIA SLIM 12 P Manual de lista de piezas
Olimpia splendid
Olimpia splendid Secco Prof Manual del propietario
Olimpia splendid
Olimpia splendid PROCOOL 16 E Hoja de especificaciones
Olimpia splendid
Olimpia splendid SeccoPur S Manual de lista de piezas
Olimpia splendid
Olimpia splendid AQUARIA 18 Manual de lista de piezas
Olimpia splendid
Olimpia splendid AQUARIA 18 P Manual de lista de piezas
Olimpia splendid
Olimpia splendid SECCOPROF 30 P Hoja de especificaciones
Olimpia splendid
Olimpia splendid SECCASCIUTTO Manual de lista de piezas
