Olide DSW-120N Manual de usuario
AUTOMATIC DOOR SPECIALISTS
Please note：Programming of the open and close stop points will occur after
installation. An uninstalled unit will result in constant motor rotation.
For any questions,feel free to contact us.
INSTALLATION MANUAL
Olide DSW-120N
Contents
1.
Technical Parameters..........................................................................................................................1
2.
Components...................................................................................................................................2
3.
Installations................................................................................................................................... 3
3.1
Installation example....................................................................................................................... 3
3.2
Installation of base plate..................................................................................................................4
3.3
Installation of pull arm.................................................................................................................... 5
3.4
Installation of push arm................................................................................................................... 6
3.5
Installation of operation system...................................................................................................... 8
3.6
Installation of cover................................................................................................................... ......8
3.7
Connection the operation system with the pull arm...................................................................... 9
3.8
Connection the operation system with the push arm...................................................................... 9
4.
Electrical Connections...................................................................................................................10
Control panel details......................................................................................................................10
4.1
Connections with a keypad ....................................................................................................10
4.2
Connections with a microwave sensor ....................................................................................... 11
4.3
Connections with PIR sensors ..............................................................................................
11
4.4
Connections for a safety motion top scan ..................................................................................11
4.5
Connections for push buttons....................................................................................................... 12
4.8
Connections for magnetic locks ....................................................................................................13
4.9
Connections for electric locks.................................................................................................13
4.10
Connection with the touchless hand sensor switches ................................................................... 13
4. 11
Double door synchronous settings..........................................................................................14
4.12 Wireless push buttons settings.................................................................................................15
4.13 Remote control settings.......................................................................................................16
5.
Parameters Adjustment...................................................................................................................17
5.1
hand programmer instruction.............................................................................................................17
5.2
adjustment steps................................................................................................................................18
6.
Trouble Shooting..............................................................................................................................19
4.6
Connections for wiring disabled push buttons............................................................................12
4.7
Connections for wireless handicapped push buttons .....................................................................12
1 Technical Parameters
1
Voltage: 110-220 VAC +/-10%
Power Consumption: 50W
Opening Time: 3-7 sec. @ 90 degrees
Hold Open Time: 1-30 sec. Adjustable
Max. Door Frame Depth:
Door Width:
Max. 1200mm / 47.2"
Max. Opening Angle:
450mm / 17.7"
Min. 660mm / 26"
120 degrees
Environment Temperature: -20C to 50C -4F to 122F
Protection Class: IP12D
Product Weight: 6.5Kg 14.3lbs
Dimensions: L515 x H95 x W50mm
20.3"L x 2"W x 3.75"H
2 Component
Power cable hole
Pull Arm(Option for interior opening)
Push Arm(Option for exterior opening)
2
Base Plate:
Sensor cable hole
Motor Assembly:
Off/On Switch
Motor
Gear box
Control block
Motor output
Cover Plate:
3
Installation
3.1 Installation example
Pull Arm
The door opens to the inside toward the unit using the pull arm assembly.
Push Arm
The door opens to the outside away from the unit using the push arm assembly.
3
3
Installation
3.2 Installation of base plate
0.88"(22.5mm)
5.90"(150mm)
5.90"(150mm) 6.49"(165mm)
1.2"(30.5mm)
hole
2.0"(52mm)
1.18"(30mm)
Right side hinge
0.88"(22.5mm)
6.49"(165mm)
1.2"(30.5mm)
2.0"(52mm)
Left side hinge
4
18.2"（464.5mm)
As the picture shows, the base plate should
be mounted to the frame with eight wood
screws or eight M6-15 countersunk screws.
Please note that 20mm sensor cable hole is
always to the right side and that the power
cable access is always to the left. The sensor
cable access hole is very near the edge of the
plate.
0.59"(15mm)
1.5"(38.5mm)
18.2"(464.5mm)
0.59"(15mm)
1.5"(38.5mm)
As the picture shows, the base plate should
be mounted to the frame with eight wood
screws or eight M6-15 countersunk screws.
1.18"(30mm)
5.90"(150mm) 5.90"(150mm)
3
Installation
3.3 Installation of Pull arm
5
Adjust the opening angle by
moving the stopper
(The stopper is at the left side
when left hand installation).
At door right
240（9.44")
（
240(9.44")
20
160(6.3")
Fix the slide rail of pull arm on the
door panel as shown using three
round head wood
Screws
(if the door panel is steel, please
use M6*15 cross recessed head
screws.)
Attach the slide rail of the pull
arm on the door panel as shown
using 3 screws
0.78"
29(1.44")
3
Installation
12.40"(315mm)
3.4 Installation of Push arm
Loosen this 3 bolts and adjust the push arm length
according to the door depth(L) until the angle between
the push arm and the door panel is 90° . At door right
6
50(1.96") 290(11.42")
Fix the support holder of push arm on the door panel as shown
using two round head wood screws
(if the door panel is steel, please use M6*15 cross
recessed head screws.)
35(1.29")
3
Installation
7
3.4 Installation of Push arm
Stop screw
Adjust the stop screw position slotted
hole to allow full opening of the door. Do
not exceed 90°.
3
Installation
8
3.5 operation system
Hook the component assembly onto the base plate as shown.
Attach it with 8 allen head screws
3.6 Cover
Opening the cover
Tabla de contenidos
