Ojmar LOCKR COMBI 8001 Guía

INSTALLATION

1.

Mark position of cut out on door, ensuring that cam in

locked position will fit into keep or strike plate of door

frame.

Cut out door as dimensioned bellow. Cut must be clean

and smooth free from burrs.

2.

Position the handle frame onto the lock from the

rear. Insert the lock together with handle into the

door cut out. See diagram bellow:

Ojmar S.A. Polígono Industrial de

Lerun, s/n 20870 Elgoibar · Spain

T. +34 943 748484

www.ojmar.com

Ojmar US

17155 Von Karman Ave, Suite 111, Irvine

CA. 92614 - USA

T. 1-949 419 6776

www.ojmar.us

V.2

LOCK 8001 / INSTALLATION AND

ASSEMBLY v.01

3.

The lock as standard is supplied with two length of fixing screws that will allow the lock to be fitted to doors between

12mm (15/32”) and 20mm (3/4”). Should doors be thinner than 12mm (15/32”) then packing pieces can be supplied

(sold separately). Please see sizing chart bellow to select the correct screws to fit door thickness and if packing piece is

required.

Fastening plate pad

4.

Fit lock to door, placing fixing plate onto the

inside of the door. See diagram bellow:

5.

Secure the lock to the door using correct length

fixing M3 screws from inside of the door. See

diagram bellow:

Do not overtighten, max torque of 150 Ncm,

111ftlbs.

Door Thickness

Pad Thickness

L Screw

1 mm (3/64”)

5 mm (13/64”) , 10 mm (3/8”)

25 mm (1”)

2(5/65”) to 4 mm (5/32”)

10 mm (3/8”)

20 mm (3/4”)

5(13/64”) to 6 mm (15/64”)

10 mm (3/8”)

25 mm (1”)

7 (9/32”) to 9 mm (23/64”)

5 mm (13/64”)

20 mm (3/4”)

10 (3/8”) to 11 mm (7/16”)

5 mm (13/64”)

25 mm (1”)

12 (15/32”) to 14 mm (35/64”)

0

20 mm (3/4”)

15 (19/32”) to 20 mm (3/4”)

0

25 mm (1”)

HOW TO CONVERT A RIGHT HAND (RH) LOCK TO A LEFT HAND (LH) LOCK

Important!

Please note all locks are supplied as stardard as RH.

(See diagram bellow) If LH locks are required please

change hand before fitting.

Before converting to a LH lock please ensure key

cylinder is inserted.

Right hand

Lock

2.

Unscrew the fixing screw from the cam, removing

both the cam and washer. Do not turn. Please note

position of end cap. See diagram bellow:

1.

Ensure that the lock is in the open position with the

cam and the blue indicator in the locked position See

diagram bellow:

Note position of end cap

in place for RH operation.

3.

Remove end cap.

5.

Refit cam and washer in the open vertical position.

The lock will now work for LH operation. See diagram

bellow:

4.

Turn end cap horizontally 180º and replace. Please note

position of end cap. See diagram bellow:

Note position of end

cap in place for LH

operation

Left hand

Lock

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Kwikset

Kwikset 48334/01 Manual de usuario