OHAUS SCOUT Manual de usuario

ScoutTM

Ethernet Interface

INSTRUCTION MANUAL

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

Ethernet Interface EN-1

INTRODUCTION

This Interface Kit is for use with Ohaus Scout STX, SPX, SKX and SJX series

products.

INTERFACE INSTALLATION

Install the Interface module on the mini DIN port (round connector) located at the

rear side of the balance as shown. During this process, please make sure the

balance is powered off.

Notes:

Please make sure the small triangle mark (▲) on the round connector is at

the bottom and then plug in.

The appearance of your model may be different.

SETUP

Upon installation, the balance will recognize the Ethernet Interface Kit and add the

following items to the menu structure. Configure the balance to the desired Ethernet

and printing parameters.

CAUTION: Invalid or incorrect Ethernet parameters may impact your network

system or lose network connectivity. Please check with your network administrator

before use.

For SPX, SKX and SJX Balances:

Upon installation, the balance will show [E.t.h.n.e.t] during the power sequence.

Reset: no, yes

Stable: off, on

A.Print: off

On.stable (->Load, Load.Zero)

interval (-> 1….3600)

continuous

Content: Result (-> off, on)

Gross (-> off, on)

Net (-> off, on)

Tare (-> off, on)

Header (-> off, on)

Footer (-> off, on)

Mode (-> off, on)

Unit (-> off, on)

Info (-> off, on)

Layout: Format (->Single, Multi)

Feed (->Line, 4 Lines, Form)

End Print: Exit menu

Ethrnt

IP Adr

End

Note: Items with bold font are default settings.

Mini DIN port

(Round connector)

EN-2 Ethernet Interface

SETUP DEFINITIONS

Menu Settings

Explanation

PRINT / A. Print – Off

Only sends data when PRINT is pressed.

PRINT / A.Print / On.Stable – Load,

Load.Zero

Balance only transmits stable data.

Load: Print stable value excluding zero

Load.Zero: Print stable value including zero

PRINT / A.Print / interval - (xx) sec

Balance sends data every (xx) seconds.

PRINT / Auto Print – accept

Balance only sends stable accept data in Check

mode.

PRINT / A.Print – Continuous

Balance repeatedly sends data as fast as

possible.

PRINT / Content

On: print relevant content after weighing data

Gross – on: G; Net – on: N; Tare – on: T;

Info – on: balance will print application mode

setting parameters

PRINT / Layout / Format - (Single,

Multi)

Single: print all data in one line

Multi: print all data in multiple lines

PRINT / Layout / Feed - (Line, 4

Lines, Form)

Line: feed one line after printing

4 Lines: feed four lines after printing

Form: feed one page after printing (move to the

top of next page after printing)

Ethrnt / IP Adr

Displays the balance's IP Address

Use the “No” and “Back” keys to show the entire

number on the display

Ethernet Connection

The Interface has a preset IP Address. The Port Number is always 9761 and

cannot be changed. For more Ethernet configuration, please refer to the Section

Ethernet Configuration.

For STX Balances:

Upon installation, the STX balance will show the Ethernet icon ( ) in the upper

right corner.

Menu added

Function

Communication

|--Ethernet

|--Ethernet Settings

|--Print Settings

For more info, please refer to the STX instruction

manual.

Ethernet Interface EN-3

DHCP is set to "On"

The IP Address will be automatically assigned by the IP share or router.

DHCP is set to "Off"

The user can setup the IP Address, Mask, Gateway, Primary DNS,

Alternate DNS and Host Name in the white field shown below.

Note: The Ethernet parameters can also be set refer to the Section Ethernet

Configuration.

Ethernet Connection

The Interface has a preset IP Address. The Port Number is always 9761 and

cannot be changed.

OPERATION

Output

With the interface installed the balance will operate in several ways according to the

settings.

Print format can be switched by xFMT user command.

New Scout Print Format (Default Format):

Output String (Non Check Weighing Applications):

[weight] 11 characters (right justified)

[space] 1 character

[unit] 5 characters (right justified)

[space] 1 character

[stability indicator] 1 character; "?" when unstable, space when stable

[space] 1 character

[T/N/G/PT] 2 characters (right justified)

[Term] 2 characters

EN-4 Ethernet Interface

Note: All of the fields have fixed length.

Output example:

*****192.21_****g_*_**

*******0.01_****g_?_**

*******95.0_****g_*_*N

******169.6_****g_*_*G

*******95.0_****g_*_*N

*******74.6_****g_*_*T

A.Print: off; Stable: off

Stable reading

unstable reading

A.Print: off; Stable: on

Content / Result -> on

Content / Gross -> on

Content / Net -> on

Content / Tare -> on

Output String (Check Weighing Application):

[weight] 11 characters (right justified)

[space] 1 character

[unit] 5 characters (right justified)

[space] 1 character

[stability indicator] 1 character; "?" when unstable, space when stable

[space] 1 character

[T/N/G/PT] 2 characters (right justified)

[space] 1 character

[application status] 6 characters (right justified)

[Term] 2 characters

Example:

*****192.21_****g_*_**_Accept

*******0.01_****g_?_**__Under

A.Print: off; Stable: off

Stable reading,

Unstable reading

Scout Pro Print Format 1 (for the models 303/123/202/402/602/2001/6001/

401FZH/601FZH/6000FZH):

Output String:

[weight] 12 characters (right justified)

[space] 1 character

[unit] 5 characters (left justified)

[space] 1 character

[stability indicator] 1 character; "?" when unstable, space when stable

[Legend] 1~10 characters

Ethernet Interface EN-5

Output example:

********0.00_g****_*

*******12.73_g****_?

********0.85_oz***_WET*WT

Scout Pro Print Format 2 (for the models 401/601/6000):

Output String:

[weight] 11 or 12 characters (right justified)

[space] 1 character

[unit] 1~5 characters

[space] 1 character

[stability indicator] 1 character; "?" when unstable, space when stable

[space] 1 character

[Legend] 1~10 characters

Note: The unit field length varies with different units. The weight field could be

11 or 12, depending on if the weight string has a dot or not.

Output example:

Print Format 3 (for Certain POS Systems):

Output String:

[weight] 11 characters (right justified)

[space] 1 character

[unit] 5 characters (right justified)

[stability indicator] 1 character; "?" when unstable, space when stable

[Term] 2 characters

Note: All of the fields have fixed length.

Output example:

*********100_g_*_

*********273_g_?_

*********8.5_oz***_WET*WT

*******0.00_****g*

******12.73_****g?

EN-6 Ethernet Interface

Input: The following interface commands will be acknowledged by the Balance.

They are case sensitive. The balance will return “ES” for invalid commands.

Command

Function

Immediate Print of displayed weight (stable or unstable).

Print displayed weight (stable or unstable).

Continuous Print.

Print on Stability.

SLP

Auto Print stable non-zero displayed weight.

SLZP

Auto Print stable non-zero weight and stable zero reading.

Interval Print x = Print Interval (1-3600 sec) 0P ends interval Print

Turn off Auto Print

H x “text” Enter Header line , where x = line number 1 to 5, “text” = header

text up to 24 alphanumeric characters

F x “text” Enter Footer line , where x = line number 1 to 2, “text” = footer

text up to 24 alphanumeric characters

Same as pressing Zero Key

Same as pressing Tare Key.

Establish a preset Tare value in displayed unit. x = preset tare value.

Sending 0T clears tare (if allowed).

Prints Tare weight stored in memory.

Print current application mode (weighing mode).

Set current application mode to x. x depends on application

1M: WEIGH, 2M: COUNT,3M: PERCENT, 4M: CHECK, 5M: DYNAMIC, 6M:

TOTAL, 7M:DENSITY, 8M: HOLD, 9M:MOLE

Scroll to the next enabled mode.

Print Current weighing unit: g, kg, lb, oz, etc….

Set balance to unit x: g, kg etc.

1U: g, 2U: kg,3U: ct, 4U: N, 5U: oz, 6U: ozt, 7U: dwt, 8U: lb, 9U:lb:oz, 10U:

grn, 11U: thk, 12U: tsg, 13U:ttw , 14U: tola, 15U:c

Scroll to the next enabled unit.

Brings out of Standby

OFF

Goes to Standby.

Begin Span Calibration

Abort Calibration.

PSN

Print Serial Number.

Print Version: print name, software revision and LFT ON (if LFT is set ON).

Set Counting APW (x) in grams. (must have APW stored)

Print Counting application APW.

Set Percent application reference weight (x) in grams. (must have reference

weight stored)

Print Percent application reference weight.

xCO

Set Checkweighing Over Limit in grams x.

xCU

Set Checkweighing Under Limit in grams x.

PCO

Print Checkweighing Over Limit.

PCU

Print Checkweighing Under Limit.

xMM

Set Molar Mass in g/mol .

PMM

Print Molar Mass

0 = print unstable data, 1 = print stable only

xFMT

0 = New Scout print format (default) ; 1 = Scout Pro print format 1;

2 = Scout Pro print format 2; 3 = for certain POS system.

xRL

0 = disable response; 1 = enable response.

Ethernet Interface EN-7

ETHERNET CONFIGURATION

To set the Ethernet parameters per web.

1. Make sure the Ethernet Interface Kit is installed properly and network cable is

connected to a computer (PC).

2. Set the PC to obtain an IP address automatically as shown below.

3. Open the IE Browser and enter the default IP address of the Ethernet

Interface Kit "169.254.1.1" ( ), the browser will

show below page:

4. Click the "Network Configuration" on the left side, and input the user &

password. Then click "OK" to proceed.

5. Input the Ethernet parameters in the following page, click “Save Config“ to

save the changes.

Note:

To use DHCP, enable the DHCP:

User: ohaus

Password: ohaus

EN-8 Ethernet Interface

To use static IP address, disable the DHCP: and then set the

Ethernet configuration parameters.

ACCESSORIES

For a complete listing of Ohaus printers and other accessories, contact Ohaus

Corporation or visit www.ohaus.com.

COMPLIANCE

This accessory has been tested and complies with the approvals listed in the

applicable Instruction Manual.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Please note that changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

Otros manuales para SCOUT

Tabla de contenidos

Otros manuales de Equipo de grabación de OHAUS

OHAUS

OHAUS R71-2ND Manual de usuario

OHAUS

OHAUS Valor 1000 Manual de usuario

OHAUS

OHAUS SCOUT Manual de usuario

OHAUS

OHAUS ranger 7000 Manual de usuario

OHAUS

OHAUS RS232 Manual de usuario

OHAUS

OHAUS Scout 30268985 Manual de usuario

OHAUS

OHAUS SCOUT Manual de usuario

OHAUS

OHAUS Scout 30268986 Manual de usuario

OHAUS

OHAUS RS232 Manual de usuario

OHAUS

OHAUS Ranger Count 3000 Series Manual de usuario

OHAUS

OHAUS ranger 7000 Manual de usuario

OHAUS

OHAUS RS232 Manual de usuario

OHAUS

OHAUS Ranger 4000 Count Series Manual de usuario

OHAUS

OHAUS SCOUT Manual de usuario

OHAUS

OHAUS SCOUT Manual de usuario

OHAUS

OHAUS Navigator Manual de usuario

OHAUS

OHAUS Ranger 3000 Series Manual de usuario

OHAUS

OHAUS ranger 7000 Manual de usuario

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado