Offshore Dynamics 4166 Manual de usuario
OFFSHORE DYNAMICS DUAL ENGINE DISPLAY
Part Numbers: 4166
USER MANUAL
Revision A\V1.0.0
1 of 10
1Introduction...................................................... 2
1.1 Product features................................................ 2
2Unit dimensions................................................. 4
3Installation........................................................ 4
3.1 Unpacking the box............................................. 4
3.2 Mounting the unit.............................................. 4
3.3 Connecting the marine display............................. 6
3.4 Selecting engine manufacturer & device set up..... 7
3.5 Mounting the Control Panel................................ 8
4Button functions............................................... 9
5Technical support.............................................. 10
6Warranty.......................................................... 11
INTRODUCTION
1
2 of 10
The Offshore Dynamics NMEA2000® Dual Engine Display has a 10.4” diagonal display area and
has a high bright sunlight readable 1000 cd/m2 display.
The Dual Engine Display can monitor two user selectable engines simultaneously, with alarm
monitoring and logging.
It is supplied with a wired remote button panel, which can control the brightness of the display,
acknowledge and clear alarm conditions
1.1 PRODUCT FEATURES
The Offshore Dynamics NMEA2000® Dual Engine Display has the following features:
• Sunlight readable dimmable display using our BlackGlass™ technology
• 768 x 1024 Resolution
• Remote button panel providing: Brightness up/down, Alarm Mute
• Monitoring of vessels engine status with alarms
• Internal 105dB Sounder
•Includes 1 x NMEA2000® and 2x J1939 interfaces
• Switchable internal line terminator resistors for J1939 interfaces
• User selectable Engine Manufacturer (MTU, MANN, Caterpillar & others) via rotary
switch on rear of display
• User selectable metric or US imperial units
• Toughened glass screen
•IP rating for of IP65 for the front and IP20 for the rear of the display
3 of 10
2UNIT DIMENSIONS
Dual Engine Display
199.5
252
52.4
5
199.5
252
1
ON
2 3 4 5 6 7 8
INSTALLATION
3
193.5
192.5
246.0
245.0
4 of 10
3.1 UNPACKING THE BOX
You will nd the following items in the shipping box:
1 x Dual Engine Display
1 x Remote button panel
1 x DC Power cable
1 x Bag containing 4 thumbwheel nuts & 4 sprung washers for button panel
1 x Bag containing 4 screws & 4 mounting clamps
1 x User Manual (This Document)
1 x Mounting cut out template
3.2 MOUNTING THE UNIT
1. The unit should be mounted through a panel to a at surface min 8mm, max 25mm.
2. It can be mounted 45 degrees either way of vertical.
3. Ensure an adequate ventilation around the product to prevent heat build up
or a minimum of 50mm.
4. Remember to allow enough clearance for access to cables and connectors. Cables
should be restrained to prevent damage to connectors.
Drawing showing panel cut out.
5 of 10
5. The unit should be sealed to the mounting surface using a suitable silicone sealant.
This Silicone sealant will be part of the seal used to provide the IP rating for the
product.
6. Using the 4 mounting clamps to the rear of display secure the unit to the mounting
surface by tightening the screws.
1
ON
234 5 678
Ethernet
Configuration
Switch
Engine
Selector
Switch
USB
Line
Termination
Remote
Panel
Switch
Aux Relay
Contacts
J1939
Port
J1939
STBD
NMEA2000®
Connector
6 of 10
3.3 CONNECTING THE DUAL ENGINE DISPLAY
Before making any connections to the unit, ensure the NMEA2000® bus power and DC supply
are turned off.
Connect NMEA2000® cable to ‘Socket’ on the back of the unit, observing correct orientation
to ensure the keyway aligns. The cable can be extended up to 6mtrs and connect into the
T-adapter on the network backbone. Ensure that the screw ring is securely tightened so that the
connection remains sound.
Connect the two J1939 cables in the same manner.
Ethernet connector is for internal Offshore programming use ONLY.
The DC Power cable can be inserted into the port marked. Ensure correct orientation and make
sure the screw ring is securely tightened. There are two USB A and one USB OTG connectors,
these are for program updates only.
Connect the Control Panel D Type Connector to the 15Way Remote Control Panel. Please see
image below for reference.
24 VDC
7 of 10
3.4 SELECTING ENGINE MANUFACTURER & DEVICE SET UP
Situated on the rear of the unit is an 8 Way Conguration switch & Rotary Switch. Their
functions are as follows:
Conguration switch
Switch No. Engine manufacturer Engine data source
0Caterpillar J1939
1Cummins NMEA2000®
2MAN J1939
3MTU J1939
4Volvo NMEA2000® from their gateway
5Yanmar NMEA2000®
6 - -
7 - -
8 - -
9 - -
AEvinrude NMEA2000®
B Honda NMEA2000®
CMercury NMEA2000® from their Smartcraft adaptor
D - -
E - -
F - -
Switch No. Switch OFF Switch ON
1 Imperial units Metric Units
2 One fuel display bar Two fuel display bars
3 Two engine displays Three engine displays
4 As per switch 3 Four engines displays
5 No J1939 Data Conversion Retransmit J1939 data over NMEA200® port
6 - -
7 - -
8 - -
Rotary switch
8 of 10
3.5 MOUNTING THE CONTROL PANEL
Please see line drawing showing outline, mounting studs and mounting area for the Control
Panel. Mounting cut out template should be used as a reference for installation.
FRONT VIEW
TOP VIEW
PANEL MOUNT CUTOUT
Mounting
studs
Mounting
studs
Cut out
102,50
32,50
64,75
36,96
81
83
90.5
25
20.5
4 x 4.5
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
