OEM Tools 24533 Manual de servicio
UNPACKING
After unpacking unit, inspect
carefully for any damage that
may have occurred during transit.
Check for loose, missing, or
damaged parts. If any damage
is observed, a shipping damage
claim must be filed with carrier.
Do not use Air Operated Vacuum
Pump if broken, bent, cracked or
damaged parts (including labels)
are noted. Any Air Operated
Vacuum Pump that appears
damaged in any way, operates
abnormally or is missing parts
should be removed from service
immediately. If you suspect that
the engine was subjected to
a shock load (a load that was
dropped suddenly, unexpectedly,
etc.) immediately discontinue use
until it has been checked by a
factory authorized service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect
yourself and others by observing all safety information, warnings, and cautions. Failure to comply with instructions
could result in personal injury and/or damage to product or property. Please retain instructions for future reference.
The following safety information is provided as guidelines to help you operate your Air Operated Vacuum
Pump under the safest possible conditions. Any tool or piece of equipment can be potentially dangerous to
use when safety or safe handling instructions are not known or not followed. The following safety instructions
are to provide the user with the information necessary for safe use and operation. Please read and retain these
instructions for the continued safe use of your service system. Failure to follow instructions listed below may
result in serious injury. In addition, make certain that anyone that uses the equipment understands and follows
these safety instructions as well.
Operating Instructions and Parts Manual 24533
03/14
2014 ©OEM-TOOLS
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
AIR VACUUM PUMP
WARNING
2
Operating Instructions and Parts Manual 24533
AIR VACUUM PUMP
Thank you very much for choosing an OEMTOOLS
Product!
For future reference, please complete the owner’s
record below:
Model: _______________ Purchase Date: _______________
Save the receipt, warranty and these instructions. It is
important that you read the entire manual to become
familiar with this product before you begin using it.
This machine is designed for certain applications
only. OEMTOOLS cannot be responsible for issues
arising from modification. We strongly recommend
this machine is not modified and/or used for
any application other than that for which it was
designed. If you have any questions relative to a
particular application, DO NOT use the machine until
you have first contacted OEMTOOLS to determine if
it can or should be performed on the product.
For technical questions please call 1-866-458-2472.
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
• Keep bystanders, children, and visitors away
while operating the Air Operated Vacuum Pump.
Distractions can cause you to lose control. Protect
others in the work area from injury.
• Stay alert. Watch what you are doing, and use
common sense when operating the Air Operated
Vacuum Pump. Do not use the tool while tired or
under the influence of drugs, alcohol, or medication.
A moment of inattention while operating the tool may
result in serious personal injury.
• Do not overreach. Keep proper footing and balance at
all times. Proper footing and balance enables better
control of the power tool in unexpected situations.
• Use safety equipment.
• Wear ANSI-approved safety glasses underneath a full
face safety shield. Nonskid safety shoes, hard hat,
or hearing protection must be used for appropriate
conditions.
• Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for
which it is designed.
• Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
• Maintain tools with care.
• Keep tools dry and clean.
• Properly maintained tools are less likely to bind and
are easier to control. Do not use a damaged tool. Tag
damaged tools “Do not use” until repaired.
• Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool’s operation.
• If damaged, have the tool serviced before using. Many
accidents are caused by poorly maintained tools.
• Use only accessories that are recommended by the
manufacturer for your model. Accessories that may
be suitable for one tool may become hazardous when
used on another tool.
• Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
• When servicing a tool, use only identical replacement
parts. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of injury.
• Maintain a safe working environment. Keep the work
area well lit. Make sure there is adequate surrounding
workspace. Keep the work area free of obstructions,
grease, oil, trash, and other debris. Do not use this
product in a damp or wet location.
• Maintain labels and nameplates on this product.
These carry important information. If unreadable or
missing, contact OEM for a replacement.
• Keep the handle dry, clean, and free from brake fluid,
oil, and grease.
• Before use, read and understand all warnings, safety
precautions, and instructions as outlined in the
vehicle manufacturer’s service manual. It is beyond
the scope of this manual to properly describe the
correct procedure and test data for each vehicle.
• To reduce the risk of discomfort, illness, or death,
read, understand, and follow the following safety
instructions. Avoid breathing A/C refrigerant and
lubricant vapor mist. Exposure may irritate eyes, nose,
and throat. To remove R134a from the A/C system, use
service equipment certified to meet the requirements
of SAE J2788--R134a recycling equipment. Additional
health and safety information may be obtained from
refrigerant and lubricant manufacturers.
03/14
2014 ©OEM-TOOLS
3
Operating Instructions and Parts Manual 24533
AIR VACUUM PUMP
• Always perform vehicle service in a properly ventilated
area. Never run an engine without proper ventilation
for its exhaust. Stop work and take necessary steps
to improve ventilation in the work area if you develop
momentary eye, nose, or throat irritation as this
indicates inadequate ventilation.
• Engine parts that are in motion and unexpected
movement of a vehicle can injure or kill. When working
near moving engine parts, wear snug fit clothing and
keep hands and fingers away from moving parts.
Keep hoses and tools clear of moving parts. Always
stay clear of moving engine parts. Hoses and tools
can be thrown through the air if not kept clear of
moving engine parts. The unexpected movement of
a vehicle can injure or kill. When working on vehicles
always set the parking brake or block the wheels.
• Be alert for hot engine parts to avoid accidental burns.
• When under pressure, refrigerants become liquid.
When accidentally released from the liquid state they
evaporate and become gaseous. As they evaporate,
they can freeze tissue very rapidly. When these gases
are breathed in, the lungs can be seriously damaged.
If sufficient quantities are taken into the lungs, death
can result. If you believe you have exposed your
lungs to released refrigerant, seek immediate medical
assistance. Refrigerants can cause frostbite and
severe burns to exposed skin. Refrigerants are under
pressure and can be forcibly sprayed in all directions
if carelessly handled. Avoid contact with refrigerants
and always wear protective gloves and make certain
other exposed skin is properly covered. Refrigerants
can also severely injure or cause permanent blindness
to unprotected eyes. Avoid contact with refrigerants
and always wear safety goggles.
• Avoid accidental fire and/or explosion. Do not smoke
near engine fuel and battery components.
• The warnings, precautions, and instructions discussed
in this manual cannot cover all possible conditions
and situations that may occur. The operator must
understand that common sense and caution are
factors which cannot be built into this product, but
must be supplied by the operator.
• The manufacturer declines any and all responsibility
for damage to vehicles or components if said damage
is the result of unskillful handling by the operator or of
failure to observe the basic safety rules set forth in the
instruction manual.
DISPOSAL
At the end of the useful life of the Air Operated Vacuum
Pump, dispose of the components according to all
state, federal, and local regulations
All technicians opening the refrigeration circuit in
automotive air conditioning systems must now
be certified in refrigerant recovery and recycling
procedures to be in compliance with Section 609
of the Clean Air Act Amendments of 1990. For
information on certification call MACS Worldwide at
(215) 631-7020.
PURPOSE
The 24533 Air Operated Vacuum Pump is a Venturi-
type vacuum pump powered by compressed air and
designed for air conditioning service
The 1990 amendments to the United States Clean Air
Act mandate that all personnel who service refrigerant
systems must be trained and certified. Fines are
in place for violations and compliance is not being
monitored by the U.S. EPA.
Do Not Vent Refrigerant to the Atmosphere. Use
Appropriate Recovery Equipment.
This pump is designed to remove air and moisture
from an AC System. The system must be empty before
using this Vacuum Pump.
Do not connect to a system under pressure.
Any system found to be under pressure, by law must
be fully evacuated with approved recovery equipment.
Only after the system is completely emptied of all
refrigerant can the pump be used.
Note: Use a quick-disconnect fitting on the “Air Input”
fitting for fast, easy connections to the air supply
03/14
2014 ©OEM-TOOLS
Air Pressure Range 75-180 PSI
Recommended Air Pres-
sure 75 PSI
Air Consumption 4.2 CFM @ 90 PSI
Vacuum Capacity 28.3” of Mercury @ 90 PSI
Run Time Recommended 10-20 Minutes
PRODUCT SPECIFICATIONS
WARNING
4
Operating Instructions and Parts Manual 24533
AIR VACUUM PUMP
03/14
2014 ©OEM-TOOLS
Figure Description Quantity
24533-1 Cover 1
24533-2 Cushion Feet
(Not shown) 4
24533-3 Aluminum Block
(Not shown)
1
24533-4 Tube M10
(Not shown)
1
24533-5 Seal Cap R12 1
24533-6 Vacuum Fitting
R12/R134a
1
24533-7 Seal Cap R134a 1
24533-8 Air Fitting 1
24533-9 O-ring
(Not shown)
1
24533-10 Washer
(Not shown)
1
NOTE
Not all components of the Air Operated
Vacuum Pump are replacement items, but
are illustrated as a convenient reference
for location and position in the assembly
sequence.
(8)
Air Fitting
(2)
Cushioned
Feet
(1)
Cover
(5)
Seal Cap R12
(7)
Seal Cap R134a
(6)
Vacuum Fitting
R12/R134a
5
Operating Instructions and Parts Manual 24533
AIR VACUUM PUMP
Always wear safety glasses and gloves!
OPERATING INSTRUCTIONS
1. Connect user supplied A/C Manifold to system. (Be sure all manifold valves are closed before connecting)
2. Connect the center hose of the Manifold Gauge Set to the “Vacuum” tee fitting (either R-12 or R-134a) on
the front of the pump. Tightly cap the port not used.
3. Open both valves on the manifold
4. Connect compressed air supply to Vacuum Pump Inlet. The low side gauge should drop below zero and
continue falling. Once gauge reaches its lowest point, let the vacuum pump run for at least 10 and preferably
20 minutes.
5. Closed both manifold valves and disconnect air supply from the vacuum pump.
6. Let system stand for at least 5 minutes to ensure the system is not leaking. If the gauge does not move, no
leaks exist.
7. Follow manufacturer’s instructions to recharge AC System.
MAINTENANCE
1. Always store the Air Operated Vacuum Pump Set in a well-protected area where it will not be exposed to
inclement weather, corrosive vapors, abrasive dust, or any other harmful elements.
2. Keep the Air Operated Vacuum Pump clean for better and safer performance.
WARNING
6
Operating Instructions and Parts Manual 24533
AIR VACUUM PUMP
OEMTOOLS™ YEAR LIMITED WARRANTY
From one year from the original purchase date of this product, OEMTOOLS will warranty this product. If you
find any defect in material or workmanship, through normal usage, return it to the place of purchase or to
OEMTOOLS for repair or replacement at our discretion. In order to obtain this service send your tool and proof
of purchase, transportation pre-paid, to OEMTOOLS Q.A. Dept., 3850 Raines Road #3, Memphis, TN 38118.
We will not be responsible for lost or damaged goods during transportation, please insure your package. If
our inspection verifies the defect, we will either repair or replace the product at our election, or we may elect
to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes
not within the scope of our warranty, then you must bear the cost of returning the product.
OEMTOOLS does not provide warranty for products labeled other than OEM or OEMTOOLS. OEMTOOLS will
not provide any warranty for products subjected to abnormal use. Abnormal use includes, but is not limited to,
abuse, accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does not
cover bits, blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or
replace blades, bits, files, and batteries as necessary. OEMTOOLS reserves the right to makes any changes in
construction or design at any time without any obligation in incorporating such changes to tools or equipment
previously sold.
OEMTOOLS makes every effort to assure that its products meet high quality and durability standards, and
warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of one year from the date of purchase. This warranty does not apply to damage due directly or indirectly
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS
WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may
also have other rights, which vary from state to state.
03/14
2014 ©OEM-TOOLS
Tabla de contenidos
Otros manuales de Bomba de agua de OEM Tools
Manuales populares de Bomba de agua de otras marcas
Sykes AmeriPumps
Sykes AmeriPumps GP100M Guía de solución de problemas
DUROMAX
DUROMAX XP WX Series Manual de usuario
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Manual de usuario
Franklin Electric
Franklin Electric IPS Manual de usuario
Xylem
Xylem e-1532 Series Manual de usuario
Milton Roy
Milton Roy PRIMEROYAL Manual de usuario