C Copyright 2021 by O.S.Engines Mfg. Co., Ltd. All rights reserved. 102100
Setting range : 0~25°
Motor Timing
Default setting : 12°
Acceleration
Setting range : 20~200
Default Setting : 100
Start Power
For 2~4-pole motors, usually we recommend 0~5°
Set the value within the range shown below.
for inner rotor type : 0~10° for outer rotor type : 10~25°
Select the advance timing with the LEFT and the RIGHT buttons.
This is the speed at which the ESC reaches the top speed. Select
the acceleration value with the LEFT and the RIGHT buttons.
The setting value is 50 or lower in case a motor is turned ON/OFF
by an on-board switch of a transmitter such as gliders.
Drive Frequency
Setting choice : 8kHz / 16kHz / 32kHz
Select the value with the LEFT and the RIGHT buttons.
We recommend 32kHz for 10-pole or less motors.
Reverse Rotation
Setting choice : Normal / Reverse
Select the direction of rotation with the LEFT and the RIGHT buttons.
Brake Force
Setting range : OFF~100%
Default Setting : OFF
Set the value with the LEFT and the RIGHT buttons.
Brake Speed
Setting range : 0~2.0 seconds
Default Setting : 0.1 second
Set the value with the LEFT and the RIGHT buttons.
Setting choice : Super Soft / Very Soft / Soft / Hard
Default Setting : Soft
Select the start power with the LEFT and the RIGHT buttons.
Active Freewheel (regenerative braking system)
Setting choice : OFF / ON
Default setting : OFF
Setting range : OFF / 40~120%
Current limit
Set the value with the LEFT and the RIGHT buttons.
This parameter regulates excessive current for energy saving
and reducing heat emission.
Default setting : 100%
Setting range : OFF / ON
Default setting : OFF
Governor setting
Motor Type
Setting choice : Standard value / OMA-4013/OMA-6030/
OMH-4535
Select the value with the LEFT and the RIGHT buttons.
Select Standard value usually.
Throttle Mode
Setting choice : Automatic / set value
Set the value with the LEFT and the RIGHT buttons.
Select the setting item with the UP and the DOWN buttons.
When you do not choose “Automatic” and set the value:
PWM value for throttle stop position: 800~1200
PWM value for maximum throttle position: 1800~2200
Restore Default
Setting choice : NO / YES
Default setting : NO
Select NO or YES with the LEFT and the RIGHT buttons.
In case you select YES, press the RIGHT button again to
confirm to restore Default settings.
Select the setting item with the UP and the DOWN buttons.
Specifications, design, and contents of the instruction manual
of the motorare subject to change without prior notice for
improvement.
gines.co.jp for questions and inquiries.
Select ON or OFF with the LEFT and the RIGHT buttons.
When you use the governor, select ON and decide the values
of the following items to set the governor gain.
Minimum rotation position setting: Min Speed 1~25
Maximum rotation position setting: Max Speed 1~25
Minimum rotation position setting is the rpm when a throttle
stick is at full low position.
Maximum rotation position setting is the highest rpm setting.
Setting range : 10%~40%
Default setting : 20%
Governor Gain setting
Set the value with the LEFT and the RIGHT buttons.
The larger the value is set, the more the motor rpm increases.
Start from 20% then find your best setting.
Setting range : 1~25
Default setting : 1
Min Speed setting
Set the value with the LEFT and the RIGHT buttons to decide
the timing when the governor starts to work.
The governor starts to work the earliest at 1. At 25 it starts the
latest.
The value is usually set 1 unless you want to change it.
Setting range : 1~25
Default setting : 8
Max Speed setting
Set the value with the LEFT and the RIGHT buttons.
This is to set the speed to reach the maximum rpm according to
the throttle move.
The rpm rises linearly at 8 to the maximum rpm, but it depends
on how the throttle curve is set. Reduce the value in case the
rpm reaches the maximum rpm before full throttle.
Increase the value in case the rpm does not reach the
maximum rpm even full throttle.
TEL. (06) 6702-0225
FAX. (06) 6704-2722
6-15 3-Chome Imagawa Higashisumiyoshi-ku
Osaka 546-0003, Japan
Select ON or OFF with the LEFT and the RIGHT buttons.
The “Brake Mode” activates when the throttle stick is moved up
to 30% or more.
(Disable the function for FAI F3A competitions.)
