Nuvoton NuMicro series Manual de usuario

NUC029SGE

Jan 21, 2019 Page 1of 37 Rev 1.00

NUTINY-SDK-NUC029SGE USER MANUAL

ARM®Cortex®-M

32-bit Microcontroller

NuMicro®Family

NuTiny-SDK-NUC029SGE

User Manual

The information described in this document is the exclusive intellectual property of

Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton.

Nuvoton is providing this document only for reference purposes of NuMicro®microcontroller based system

design. Nuvoton assumes no responsibility for errors or omissions.

All data and specifications are subject to change without notice.

For additional information or questions, please contact: Nuvoton Technology Corporation.

www.nuvoton.com

NUC029SGE

Jan 21, 2019 Page 2of 37 Rev 1.00

NUTINY-SDK-NUC029SGE USER MANUAL

Table of Contents

1OVERVIEW .........................................................................................4

2NUTINY-SDK-NUC029SGE INTRODUCTION................................................5

NuTiny-SDK-NUC029SGE Jumper Description .................................................. 62.1

2.1.1 Power Setting ...................................................................................................6

2.1.2 Debug Connector ...............................................................................................6

2.1.3 USB Connector .................................................................................................6

2.1.4 Extended Connector ...........................................................................................6

2.1.5 Reset Button.....................................................................................................6

2.1.6 Power Connector ...............................................................................................6

2.1.7 VCOM Enable...................................................................................................6

Pin Assignment for Extended Connector .......................................................... 82.2

NuTiny-SDK-NUC029SGE PCB Placement......................................................202.3

3How to Start NuTiny-SDK-NUC029SGE on the Keil mdk ENVIRONMENT............ 21

Downloading and Installing Keil MDK Software..................................................213.1

Downloading and Installing Nuvoton Nu-Link Driver............................................213.2

Hardware Setup.......................................................................................213.3

Example Program.....................................................................................213.4

4How to Start NuTiny-SDK-NUC029SGE on the IAR Embedded Workbench .......... 23

Downloading and Installing IAR Embedded Workbench Software ...........................234.1

Downloading and Installing Nuvoton Nu-Link Driver............................................234.2

Hardware Setup.......................................................................................234.3

Example Program.....................................................................................234.4

5Starting to Use Nu-Link-Me 3.0 VCOM Function............................................ 25

Downloading and Installing VCOM Driver ........................................................25

5.1

VCOM Mode Setting on NuTiny-SDK-NUC029SGE............................................275.2

Development Tool Setup ............................................................................275.3

5.3.1 Check the Using UART on the Keil μVision®IDE........................................................ 27

5.3.2 Check the Target Device and Debug Setting ............................................................ 28

5.3.3Build and Download Code to NuTiny-SDK-NUC029SGE.............................................. 30

5.3.4 Open the Serial Port Terminal.............................................................................. 30

5.3.5 Reset Chip ..................................................................................................... 31

6NuTiny-SDK-NUC029SGE Schematics ...................................................... 32

Nu-Link-Me V3.0 Schematic ........................................................................326.1

NUC029SGE

Jan 21, 2019 Page 3of 37 Rev 1.00

NUTINY-SDK-NUC029SGE USER MANUAL

GPIO for 64 pin Schematic..........................................................................336.2

SDK Circuit Schematic...............................................................................346.3

Target Chip ............................................................................................356.4

7REVISION HISTORY............................................................................ 36

NUC029SGE

Jan 21, 2019 Page 4of 37 Rev 1.00

NUTINY-SDK-NUC029SGE USER MANUAL

1 OVERVIEW

NuTiny-SDK-NUC029SGE is a specific development tool for NuMicro®NUC029SGE. With the

NuTiny-SDK-NUC029SGE, user can develop and verify the application program easily.

The NuTiny-SDK-NUC029SGE includes two portions. One is NuTiny-EVB-NUC029SGE and the

other is Nu-Link-Me. NuTiny-EVB-NUC029SGE is the evaluation board and Nu-Link-Me is its

Debug Adaptor. Thus, user does not need other additional ICE or debug equipment.

The NUC029SGE can bridge the gap and replace the cost equivalent to traditional 8- and 16-bit

microcontroller by 32-bit performance and rich functions. The NUC029SGE supports a wide range

of applications from low-end, price sensitive designs to computing-intensive ones and provides

advanced high-end features in economical products.

The NuMicro®NUC029xGE of NUC029 series microcontroller based on the Arm®Cortex®-M0

core operates at up to 72 MHz. With its crystal-less USB 2.0 FS interface, it is able to generate

precise frequency required by USB protocol without the need of external crystal. It features

adjustable VDDIO pins for specific I/O pins with a wide range of voltage from 1.8 V to 5.5 V for

various operating voltages of external components, a unique high-speed PWM with clock

frequency up to 144 MHz for precision control, and an integrated hardware divider to speed up

the calculation for the control algorithms. Apart from that, the NUC029xGE also integrates

SPROM (Security Protection ROM) which provides a secure code execution area to protect the

intelligent property of developers. The NuMicro®NUC029xGE of NUC029 series is ideal for

industrial control, motor control and metering applications.

The NuMicro® NUC029xGE of NUC029 series supports the wide voltage range from 2.5 V to 5.5

V and temperature ranging from -40℃to 105℃, up to 256 Kbytes of Flash memory, 20 Kbytes of

SRAM, 4 Kbytes of ISP (In-System Programming) ROM as well as ICP (In-Circuit Programming)

ROM and IAP (In-Application Programming) ROM in 48-, 64-, 128-pin packages. It also supports

high immunity of 8KV ESD (HBM)/4KV EFT. It is also equipped with plenty of peripherals such as

USB interface, Timers, Watchdog Timers, RTC, PDMA, EBI, UART, Smart Card Interface, SPI,

I²S, I²C, GPIO, up to 12 channels of 16-bit PWM, up to 20 channels of 12-bit ADC, analog

comparator, temperature sensor, low voltage reset, brown-out detector, 96-bit UID (Unique

Identification), and 128-bit UCID (Unique Customer Identification).

Besides, the NUC029SGE is equipped with ISP (In-System Programming) and ICP (In-Circuit

Programming) functions, which allow the user to update the program memory without removing

the chip from the actual end product. The NUC029SGE also supports In-Application-

Programming (IAP) function, user switches the code executing without the chip reset after the

embedded flash updated.

NUC029SGE

Jan 21, 2019 Page 5of 37 Rev 1.00

NUTINY-SDK-NUC029SGE USER MANUAL

2 NUTINY-SDK-NUC029SGE INTRODUCTION

The NuTiny-SDK-NUC029SGE uses the NUC029SGE as the target microcontroller. Figure 2-1 is

NuTiny-SDK-NUC029SGE for the NUC029SGE, the left portion is called NuTiny-EVB-

NUC029SGE and the right portion is Debug Adaptor called Nu-Link-Me.

The NuTiny-EVB-NUC029SGE is similar to other development boards. Users can use it to

develop and verify applications to emulate the real behavior. The on board chip covers

NUC029SGE features. The NuTiny-EVB-NUC029SGE can be a real system controller to design

user’s target systems.

Nu-Link-Me is a Debug Adaptor. The Nu-Link-Me Debug Adaptor connects your PC's USB port to

your target system (via Serial Wired Debug Port) and allows you to program and debug

embedded programs on the target hardware. The Nu-Link-Me V3.0 also supports VCOM function,

which gives users more flexibility when debugging. To use the Nu-Link-Me Debug adaptor with

IAR or Keil, please refer to “Nuvoton NuMicro®IAR ICE driver user manual “or Nuvoton NuMicro®

Keil ICE driver user manual” in detail. These two documents will be stored in the local hard disk

when the user installs each driver. To use Nu-Link-Me 3.0 VCOM function, please refer to

Chapter 5.

Reset Botton (SW1)

I/O and

Power LED

Extended Connector

(JP6, JP7)

VCOM

Enable

ICE Controller

USB Connector

(J5)

ICE ControllerTarget Chip VCC: 3.3V / 5V

(JPR1)

VDD (J2)

VSS (J4)

VCOM Enable

(SW2)

Extended Connector

(JP5, JP8)

Figure 2-1 NuTiny-SDK-NUC029SGE (PCB Board)

NUC029SGE

Jan 21, 2019 Page 6of 37 Rev 1.00

NUTINY-SDK-NUC029SGE USER MANUAL

NuTiny-SDK-NUC029SGE Jumper Description2.1

2.1.1 Power Setting

J5: USB port in Nu-Link-Me

J2: VDD Voltage connecter in NuTiny-EVB-NUC029SGE

Model

JPR1

J5 USB port

J2 VDD

MCU Voltage

Model 1

Select VCC33

(default )

Connect to PC

DC 3.3V output

DC 3.3V

Model 2

DC 2.5 V ~ 5.5 V

Input

Voltage by J2

input

X: Unused.

2.1.2 Debug Connector

JP4: Connector in target board (NuTiny-EVB-NUC029SGE) for connecting with Nuvoton

ICE adaptor (Nu-Link-Me V3.0)

JP2: Connector in ICE adaptor (Nu-Link-Me V3.0) for connecting with a target board (for

example NuTiny-EVB-NUC029SGE)

2.1.3 USB Connector

J5: Micro USB Connector in Nu-Link-Me V3.0 connected to a PC USB port

2.1.4 Extended Connector

JP5, JP6, JP7, JP8: Show all chip pins in NuTiny-EVB-NUC029SGE

2.1.5 Reset Button

SW1: Reset button in NuTiny-EVB-NUC029SGE

2.1.6 Power Connector

J2: VDD connector in NuTiny-EVB-NUC029SGE

J4: VSS connector in NuTiny-EVB-NUC029SGE

2.1.7 VCOM Enable

SW2: VCOM function enable for the NuTiny-SDK-NUC029SGE. Switch SW2 on before

power on to enable VCOM function. SW2 connects pin 49(PA.3/RXD) and pin

50(PA.2/TXD) in NuTiny-EVB-NUC029SGE with pin 22(PB.1/TXD) and pin 21(PB.0/RXD)

in Nuvoton ICE adaptor (Nu-Link-Me V3.0). SW2 connects pin 29(VCOM) in Nuvoton ICE

adaptor (Nu-Link-Me V3.0) to GND to enable VCOM function.

NUC029SGE

Jan 21, 2019 Page 7of 37 Rev 1.00

NUTINY-SDK-NUC029SGE USER MANUAL

Switch Pin

Number

Function

Name

UART0 Mode

VCOM Mode

SW2

ICE_TX

Off

ICE_RX

Off

VCOM_EN

Off

X: Unused.

NUC029SGE

Jan 21, 2019 Page 8of 37 Rev 1.00

NUTINY-SDK-NUC029SGE USER MANUAL

Pin Assignment for Extended Connector2.2 The NuTiny-EVB-NUC029SGE provides NUC029SGE on board and the extended connector

(JP5, JP6, JP7 and JP8) for LQFP-64 pin.

64 Pin

Pin Name

Type

Description

PB.15

I/O

General purpose digital I/O pin.

ADC0_CH12

ADC0 channel 12 analog input.

ACMP0_P3

Analog comparator 0 positive input 3 pin.

EBI_nCS1

EBI chip select 1 output pin.

PB.5

I/O

General purpose digital I/O pin.

ADC0_CH13

ADC0 channel 13 analog input.

SPI0_MOSI

I/O

SPI0 MOSI (Master Out, Slave In) pin.

SPI1_MOSI

I/O

SPI1 MOSI (Master Out, Slave In) pin.

ACMP0_P2

Analog comparator 0 positive input 2 pin.

SC1_RST

Smart Card 1 reset pin.

EBI_AD6

I/O

EBI address/data bus bit 6.

UART2_RXD

UART2 data receiver input pin.

PB.6

I/O

General purpose digital I/O pin.

ADC0_CH14

ADC0 channel 14 analog input.

SPI0_MISO

I/O

SPI0 MISO (Master In, Slave Out) pin.

SPI1_MISO

I/O

SPI1 MISO (Master In, Slave Out) pin.

ACMP0_P1

Analog comparator 0 positive input 1 pin.

SC1_PWR

Smart Card 1 power pin.

EBI_AD5

I/O

EBI address/data bus bit 5.

PB.7

I/O

General purpose digital I/O pin.

ADC0_CH15

ADC0 channel 15 analog input.

SPI0_CLK

I/O

SPI0 serial clock pin.

SPI1_CLK

I/O

SPI1 serial clock pin.

USCI2_CTL1

I/O

USCI2 control 1 pin.

ACMP0_P0

Analog comparator 0 positive input 0 pin.

SC1_DAT

I/O

Smart Card 1 data pin.

EBI_AD4

I/O

EBI address/data bus bit 4.

NUC029SGE

Jan 21, 2019 Page 9of 37 Rev 1.00

NUTINY-SDK-NUC029SGE USER MANUAL

64 Pin

Pin Name

Type

Description

nRESET

External reset input: active LOW, with an internal pull-up. Set

this pin low reset to initial state.

PD.0

I/O

General purpose digital I/O pin.

SPI0_I2SMCLK

I/O

SPI0 I2S master clock output pin

SPI1_I2SMCLK

I/O

SPI1 I2S master clock output pin

UART0_RXD

UART0 data receiver input pin.

USCI2_CTL0

I/O

USCI2 control 0 pin.

ACMP1_N

Analog comparator 1 negative input pin.

SC1_CLK

Smart Card 1 clock pin.

INT3

External interrupt 3 input pin.

AVSS

Ground pin for analog circuit.

PD.8

I/O

General purpose digital I/O pin.

ADC0_CH17

ADC0 channel 17 analog input.

UART0_nCTS

UART0 clear to Send input pin.

USCI2_CTL1

I/O

USCI2 control 1 pin.

TM2

I/O

Timer2 event counter input/toggle output pin.

EBI_nCS0

EBI chip select 0 output pin.

PD.9

I/O

General purpose digital I/O pin.

ADC0_CH18

ADC0 channel 18 analog input.

UART0_RXD

UART0 data receiver input pin.

USCI2_CTL0

I/O

USCI2 control 0 pin.

ACMP1_P3

Analog comparator 1 positive input 3 pin.

TM3

I/O

Timer3 event counter input/toggle output pin.

EBI_ALE

EBI address latch enable output pin.

PD.1

I/O

General purpose digital I/O pin.

ADC0_CH19

ADC0 channel 19 analog input.

PWM0_SYNC_IN

PWM0 counter synchronous trigger input pin.

UART0_TXD

UART0 data transmitter output pin.

USCI2_CLK

I/O

USCI2 clock pin.

ACMP1_P2

Analog comparator 1 positive input 2 pin.

NUC029SGE

Jan 21, 2019 Page 10 of 37 Rev 1.00

NUTINY-SDK-NUC029SGE USER MANUAL

64 Pin

Pin Name

Type

Description

TM0

I/O

Timer0 event counter input/toggle output pin.

EBI_nRD

EBI read enable output pin.

PD.2

I/O

General purpose digital I/O pin.

ADC0_ST

ADC0 external trigger input pin.

TM0_EXT

I/O

Timer0 external capture input/toggle output pin.

USCI2_DAT0

I/O

USCI2 data 0 pin.

ACMP1_P1

Analog comparator 1 positive input 1 pin.

PWM0_BRAKE0

PWM0 Brake 0 input pin.

EBI_nWR

EBI write enable output pin.

INT0

External interrupt 0 input pin.

PD.3

I/O

General purpose digital I/O pin.

TM2

I/O

Timer2 event counter input/toggle output pin.

SPI0_I2SMCLK

I/O

SPI0 I2S master clock output pin

TM1_EXT

I/O

Timer1 external capture input/toggle output pin.

USCI2_DAT1

I/O

USCI2 data 1 pin.

ACMP1_P0

Analog comparator 1 positive input 0 pin.

PWM0_BRAKE1

PWM0 Brake 1 input pin.

EBI_MCLK

EBI external clock output pin.

INT1

External interrupt 1 input pin.

VBAT

Power supply by batteries for RTC.

PF.0

I/O

General purpose digital I/O pin.

X32_OUT

External 32.768 kHz crystal output pin.

USCI2_CTL1

I/O

USCI2 control 1 pin.

INT5

External interrupt 5 input pin.

PF.1

I/O

General purpose digital I/O pin.

X32_IN

External 32.768 kHz crystal input pin.

USCI2_CTL0

I/O

USCI2 control 0 pin.

PWM1_BRAKE0

PWM1 Brake 0 input pin.

PF.2

I/O

General purpose digital I/O pin.

USCI2_CLK

I/O

USCI2 clock pin.

Otros manuales para NuMicro series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de Nuvoton

Nuvoton

Nuvoton Nu-Link2-Pro Manual de usuario

Nuvoton

Nuvoton NuEdu-SDK-NUC240 Manual de usuario

Nuvoton

Nuvoton NuMicro 8051 Series Manual de usuario

Nuvoton

Nuvoton NuMaker-HMI-N9H26 Manual de usuario

Nuvoton

Nuvoton NuMaker RTU NUC980 Manual de usuario

Nuvoton

Nuvoton NuMicro NuMaker-HMI-N9H20 Manual de usuario

Nuvoton

Nuvoton NuMaker-M030GTD Manual de usuario

Nuvoton

Nuvoton NuMicro NuMaker-M467HJ Manual de usuario

Nuvoton

Nuvoton NuMaker-M471R1 Manual de usuario

Nuvoton

Nuvoton NuMaker NUC980 Manual de usuario

Nuvoton

Nuvoton NuMicro M252 Series Manual de usuario

Nuvoton

Nuvoton NuMicro NUC200 Series Manual de usuario

Nuvoton

Nuvoton NuMaker-M0A23OC Manual de usuario

Nuvoton

Nuvoton NuMicro M480 Series Manual de usuario

Nuvoton

Nuvoton NuMaker-LoRaG915 Manual de usuario

Nuvoton

Nuvoton NuMaker Tomato Manual de usuario

Nuvoton

Nuvoton NuMicro 8051 Series Manual de usuario

Nuvoton

Nuvoton NUC900 Series Manual de usuario

Nuvoton

Nuvoton NuMaker-M258KG Manual de usuario

Nuvoton

Nuvoton NuMicro 8051 Series Manual de usuario

Nuvoton

Nuvoton NuMaker NUC1262SE Manual de usuario

Nuvoton

Nuvoton NuMaker-M253LEB Manual de usuario

Nuvoton

Nuvoton NuMicro NuMaker-NUC029SGE Manual de usuario

Nuvoton

Nuvoton NuMicro NuMaker-IoT-M467 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario