Nuvoton NuMicro NuMaker-IoT-MA35D1-A1 Manual de usuario

NuMaker-IoT-MA35D1-A1

Oct. 31, 2022 Page 1of 43 Rev 1.01

NUMAKER-IOT-MA35D1-A1USER MANUAL

Maker Nu-mbed NUC472 User Manual

NuMicro®Family

Arm®Cortex®-A35-based Microprocessor

NuMaker-IoT-MA35D1-A1

User Manual

Evaluation Board for NuMicro®MA35D1 Series

The information described in this document is the exclusive intellectual property of

Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton.

Nuvoton is providing this document only for reference purposes of NuMicro microcontroller and

microprocessor based system design. Nuvoton assumes no responsibility for errors or omissions.

All data and specifications are subject to change without notice.

For additional information or questions, please contact: Nuvoton Technology Corporation.

www.nuvoton.com

NuMaker-IoT-MA35D1-A1 
 
Oct. 31, 2022 Page 2of 43 Rev 1.01 
NUMAKER-IOT-MA35D1-A1USER MANUAL 
Maker Nu-mbed NUC472 User Manual 
 
Table of Contents 
1OVERVIEW......................................................................................................6 
2FEATURES......................................................................................................8 
3HARDWARE CONFIGURATION.....................................................................9 
1 Front View....................................................................................................................... 9
2 Rear View ....................................................................................................................... 9
3 DDR PHY and MCP DRAM Power Voltage ............................................................ 10 
4 Audio Codec................................................................................................................. 10 
5 RGMII Gigabit Ethernet .............................................................................................. 10 
6 RMII Megabit Ethernet................................................................................................ 11 
7 QSPI Flash ................................................................................................................... 11 
8 NAND Flash ................................................................................................................. 11 
9 USB Virtual COM (VCOM) Port................................................................................. 12 
10 Power Jack ............................................................................................................. 12 
11 Power-on Setting ................................................................................................... 12 
12 Reset and RTC Wake-up Control ....................................................................... 15 
13 SWJ ......................................................................................................................... 15 
14 HS USB2.0 Connectors........................................................................................ 16 
15 RS232...................................................................................................................... 17 
16 RS485...................................................................................................................... 17 
17 CAN FD................................................................................................................... 17 
18 Raspberry Pi 40-pin Connector........................................................................... 17 
19 Key Buttons and LEDs.......................................................................................... 19 
20 CMOS Sensor Capture Connector ..................................................................... 20 
21 MicroSD Card Slot................................................................................................. 21 
22 Arduino UNO Compatible Extension Connectors............................................. 21 
4QUICK START...............................................................................................24 
1 Insert SD Card ............................................................................................................. 24 
2 Configure Power-on Setting....................................................................................... 24 
3 Power On the System................................................................................................. 25 
4 VCOM Port (Optional)................................................................................................. 25 
5 Press the RTC Wakeup Key Button ......................................................................... 25 
5SUPPORTING RESOURCES........................................................................27 

NuMaker-IoT-MA35D1-A1

Oct. 31, 2022 Page 3of 43 Rev 1.01

NUMAKER-IOT-MA35D1-A1USER MANUAL

Maker Nu-mbed NUC472 User Manual

5.1 Documents ................................................................................................................... 27

5.2 Software........................................................................................................................ 27

6NUMAKER-IOT-MA35D1-A1 SCHEMATICS ................................................29

6.1 Power Input Schematic............................................................................................... 29

6.2 Key Buttons and LEDs Schematic............................................................................ 30

6.3 Power-on Setting and SWJ Schematic .................................................................... 31

6.4 CCAP0 Schematic....................................................................................................... 32

6.5 RS232 and RS485 Schematic................................................................................... 33

6.6 QSPI0 and NAND Flash Schematic ......................................................................... 34

6.7 SD1 Schematic ............................................................................................................ 35

6.8 RGMII0_PE Schematic............................................................................................... 36

6.9 RMII1_PF Schematic.................................................................................................. 37

6.10 NAU88C22 Audio Codec Schematic .................................................................. 38

6.11 NUC123 VCOM Schematic.................................................................................. 39

6.12 HSUSB 0/1 Schematic.......................................................................................... 40

6.13 PCB Placement...................................................................................................... 41

7REVISION HISTORY .....................................................................................42

NuMaker-IoT-MA35D1-A1 
 
Oct. 31, 2022 Page 4of 43 Rev 1.01 
NUMAKER-IOT-MA35D1-A1USER MANUAL 
Maker Nu-mbed NUC472 User Manual 
 
List of Figures 
Figure 1-1 NuMaker-IoT-MA35D1-A1 Board ................................................................................... 7 
Figure 3-1 Front View of NuMaker-IoT-MA35D1-A1........................................................................ 9 
Figure 3-2 Rear View of NuMaker-IoT-MA35D1-A1...................................................................... 10 
Figure 3-3 RS232, RS485, CAN and Raspberry Pi Connectors.................................................... 19 
Figure 3-4 Arduino UNO Compatible Extension Connectors......................................................... 22 
Figure 4-1 SD1 MicroSD Card Slot (CON5) .................................................................................. 24 
Figure 4-2 Power-on Setting DIP Switch (SW7)............................................................................ 24 
Figure 4-3 USB VCOM Port (CON9).............................................................................................. 25 
Figure 4-4 RTC Wakeup Key Button (SW1).................................................................................. 26 
Figure 5-1 Nuvoton Website .......................................................................................................... 27 
Figure 5-2 MA35D1 GitHub Resources ......................................................................................... 28 
Figure 6-1 Power Input Schematic................................................................................................. 29 
Figure 6-2 Key Buttons and LEDs Schematic................................................................................ 30 
Figure 6-3 Power-on Setting and SWJ Schematic......................................................................... 31 
Figure 6-4 CCAP0 Schematic........................................................................................................ 32 
Figure 6-5 CAN-FD, RS232 and RS485 Schematic...................................................................... 33 
Figure 6-6 QSPI0 and NAND Flash Schematic............................................................................. 34 
Figure 6-7 SD1 Schematic............................................................................................................. 35 
Figure 6-8 RGMII0_PE Schematic................................................................................................. 36 
Figure 6-9 RMII1_PF Schematic.................................................................................................... 37 
Figure 6-10 NAU88C22 Audio Codec Schematic.......................................................................... 38 
Figure 6-11 NUC123 VCOM Schematic ........................................................................................ 39 
Figure 6-12 HSUSB 0/1 Schematic ............................................................................................... 40 
Figure 6-13 Front PCB Placement of NuMaker-IoT-MA35D1-A1 Board....................................... 41 
Figure 6-14 Rear PCB Placement of NuMaker-IoT-MA35D1-A1 Board........................................ 41 
 
 

NuMaker-IoT-MA35D1-A1 
 
Oct. 31, 2022 Page 5of 43 Rev 1.01 
NUMAKER-IOT-MA35D1-A1USER MANUAL 
Maker Nu-mbed NUC472 User Manual 
 
List of Tables 
Table 3-1 DDR PHY and MCP DRAM Power Voltage Selection................................................... 10 
Table 3-2 QSPI0 Flash (U11) Pin Function ................................................................................... 11 
Table 3-3 NAND Flash (U12) Pin Function.................................................................................... 12 
Table 3-4 NUC123 ICE Interface (J9) Pin Funciton....................................................................... 12 
Table 3-5 Secure Boot Options...................................................................................................... 13 
Table 3-6 Booting Source QSPI0 and SD/eMMC IO Voltage Options .......................................... 13 
Table 3-7 Booting Source Options................................................................................................. 13 
Table 3-8 Page Size Options for NAND Flash Booting Source..................................................... 13 
Table 3-9 ECC Options for NAND Flash Booting Source.............................................................. 14 
Table 3-10 Options for SD Card 0/1 or eMMC 0/1 NAND Flash Device Booting Source.............. 14 
Table 3-11 4/8-bit Options for eMMC NAND Flash Device Booting Source.................................. 14 
Table 3-12 1-bit Options for QSPI0 NAND/NOR Flash Booting Source........................................ 14 
Table 3-13 Options for USBD or USBH Booting Source ............................................................... 14 
Table 3-14 USBH Port 0/1 Options for USBH Booting Source...................................................... 15 
Table 3-15 Over-current High/Low-active Detect Options for USBH Booting Source................... 15 
Table 3-16 RTC Power Control Pins of MA35D1........................................................................... 15 
Table 3-17 SWJ Interface (CON12) Pin Funciton.......................................................................... 16 
Table 3-18 RS232_10 Connector (J5) Pin Funciton...................................................................... 17 
Table 3-19 RS485_12 Connector (J6) Pin Funciton...................................................................... 17 
Table 3-20 CAN_1 Connector (J2) Pin Funciton ........................................................................... 17 
Table 3-21 Raspberry Pi 40-pin Connector (CON4) Pin Funciton................................................. 19 
Table 3-22 Key Buttons (KEY_0, KEY_1, KEY_2, KEY_3) Pin Function...................................... 20 
Table 3-23 LEDs (LED_0 , LED_1, LED_2) Pin Function ............................................................. 20 
Table 3-24 CCAP0 Connector (CON3) Pin Funciton..................................................................... 21 
Table 3-25 PN11 Pin State Control for SD1 VDD_SDIO 3.3V or 1.8V Power Voltage ................. 21 
Table 3-26 PN14 or nRESET Pin State Control for SD1 MicroSD Card Power ON or OFF......... 21 
Table 3-27 Arduino UNO Interface Connector 1 (NU1) Pin Funciton............................................ 22 
Table 3-28 Arduino UNO Interface Connector 2 (NU2) Pin Funciton............................................ 23 
Table 3-29 Arduino UNO Interface Connector 3 (NU3) Pin Funciton............................................ 23 
Table 3-30 Arduino UNO Interface Connector 4 (NU4) Pin Funciton............................................ 23 
Table 4-1 SD/eMMC Boot Source Configuration on Power-on Setting......................................... 25 
Table 4-2 SD1 Booting Source Configuration on Power-on Setting.............................................. 25 
 

NuMaker-IoT-MA35D1-A1

Oct. 31, 2022 Page 6of 43 Rev 1.01

NUMAKER-IOT-MA35D1-A1USER MANUAL

Maker Nu-mbed NUC472 User Manual

1 OVERVIEW

The NuMaker-IoT-MA35D1-A1 evaluation board provides the Ethernet and connectivity features of

Nuvoton NuMicro MA35D1 series microprocessors (MPUs), based on MA35D16F987C (LQFP216

package, and stacking a 512 MB DDR). The NuMaker-IoT-MA35D1-A1 includes rich peripherals such

as one set of Gigabit Ethernet, one set of Megabit Ethernet, high-speed USB2.0 Host and device, one

set of SD2.0 in Micro SD slot, one set of CAN FD, and RS-485 and RS232 serial communication ports.

Furthermore, the NuMaker-IoT-MA35D1-A1 provides discrete power supply to be the reference design.

It also provides compatible headers with Raspberry Pi and Arduino UNO for minimizing effort in

connecting popular sensors and modules to the system. Based on these features, it helps user to

facilitate the evaluation in IIoT Edge Gateway, Smart Building, Smart Agriculture, T-Box, 4G/5G Base

Station, or your creative applications.

There are two evaluation boards for the MA35D1 series, NuMaker-HMI-MA35D1-S1 and NuMaker-IoT-

MA35D1-A1, which are ideal for HMI and edge gateway applications, respectively. For more details on

HMI applications, please refer to NuMaker-HMI-MA35D1-S1 User Manual. For more details on edge

gateway applications, please refer to NuMaker-IoT-MA35D1-A1 User Manual.

The NuMicro MA35D1 series is a heterogeneous multi-core microprocessor targeted to high-end edge

IIoT gateway. It is based on dual 64-bit Arm Cortex-A35 cores with speed up to 1 GHz, and one 180

MHz Arm Cortex-M4 core. Based on the high-performance cores, the MA35D1 series facilities the tiny

AI/ML for edge computing.

The MA35D1 series supports 16-bit DDR2 and DDR3/DDR3L SDRAM. For an easy system design and

manufacture, the MA35D1 series also offers LQFP and BGA packages stacked with the DDR2/DDR3L

SDRAM and density up to 512 MB, which significantly reduces PCB layer, size and electromagnetic

interference (EMI).

The MA35D1 series is a trusted system for IoT products' security requirements. It includes several

advanced security mechanisms such as Nuvoton Trusted Secure Island (TSI) an isolated secure

hardware unit, TrustZone, secure boot, tamper-detection, built-in cryptographic accelerators, and a

TRNG, as well as Key Store and OTP memory. All the security operations are performed in the TSI to

protect sensitive and high-value data. The features also satisfy customers in IEC 62443 certification

requirements.

For high-end edge IIoT gateway requirements, the MA35D1 series provides multiple advanced and high-

speed connection interfaces, such as Gigabit Ethernet, SDIO3.0, USB 2.0 HS, and CAN FD, for edge

gateway and new energy applications.

For HMI applications, the MA35D1 series provides a LCD display controller with the resolution up to

1920x1080 at 60 FPS, a 2D graphic engine, a JPEG and a H.264 decoder integrated for better graphical

HMI effects and video playback.

NuMaker-IoT-MA35D1-A1

Oct. 31, 2022 Page 7of 43 Rev 1.01

NUMAKER-IOT-MA35D1-A1USER MANUAL

Maker Nu-mbed NUC472 User Manual

Figure 1-1 NuMaker-IoT-MA35D1-A1 Board

NuMaker-IoT-MA35D1-A1

Oct. 31, 2022 Page 8of 43 Rev 1.01

NUMAKER-IOT-MA35D1-A1USER MANUAL

Maker Nu-mbed NUC472 User Manual

2 FEATURES

Target Chip: MA35D16F987C (LQFP216) MCP package with DDR3L (512 MB), which can

run up to 800 MHz

Power:

–5V/2A Power Jack, USB VCOM Port or HUSB0 Device

–Battery header for RTC power

Debug:

–UART0 debug port: USB Virtual COM (VCOM) port

–Debug ports: SWJ (JTAG + SWD) connector

Memory Devices

–An on-board Quad SPI NAND Flash device (512 MB)

–An on-board NAND Flash device (1 GB)

–MicroSD memory card (SD1, supports SD3.0)

One power-on setting DIP-Switch for evaluation booting source selection

One set of Gigabit Ethernet port: One Gigabit Ethernet (RGMII) PHY device, transformer

and RJ45 port connector

One set of Megabit Ethernet port: One Megabit Ethernet (RMII) PHY device, transformer

and RJ45 port connector

Two sets of high speed USB ports: One Host/Device port and one Host port

One Raspberry Pi 40-pin header connector

Arduino UNO Compatible Extension Connectors

One camera capture (CMOS sensor) header connector

One audio codec with microphone input and speaker output

One set of RS232 transceiver and header connector

One set of RS485 transceiver and header connector

One set of CAN FD transceiver and header connector

Four user key buttons

Three user LEDs

NuMaker-IoT-MA35D1-A1

Oct. 31, 2022 Page 9of 43 Rev 1.01

NUMAKER-IOT-MA35D1-A1USER MANUAL

Maker Nu-mbed NUC472 User Manual

3 HARDWARE CONFIGURATION

3.1 Front View

Figure 3-1 shows the main components and connectors from the front side of NuMaker-IoT-MA35D1-

A1 board.

Target Chip (U1): MA35D16F987C (LQFP216) MCP package with DDR3L (512MB).

Target Chip

(U1, MA35D16F787C)

QSPI0 SPI-NAND Flash

(U11, W25N04KVZEIR)

NAND Flash

(U12, W29N08GVSIAA)

CCAP0

Connector

(CON3)

HSUSB1

Host

(CON11)

USB VCOM Port

(CON9)

RGMII0 Gigabit PHY

& Transformer

(U14, RTL8211FDI)

(U15, GST5009BM)

SWJ

Connector

(CON12)

Power-on Setting

DIP Switch

(SW7)

Key Buttons

Raspberry Pi

Connector

(CON4)

RTC Battery

Connector

(J1)

Reset Key

(SW2)

Microphone

(M1)

Headset Jak

(CON8)

Audio codec

(U18, NAU88C22)

USB0_ID

Connector

(J10)

LEDs

RMII1 10/100 PHY

& Transformer

(U16, RTL8201FI)

(U17, TS8121C) RTC Wakeup Key

(SW1)

RS232_10

Transceiver &

Connector

(U8, J5)

CAN_1

Transceiver &

Connector

(U7, J2)

SWJ_nRESET

Connector

(J3)

Speaker

Connector

(J7)

HSUSB0

Host/Device

(CON10)

VCOM Controller

(U19, NUC123ZD4AN0)

NUC123 ICE

Interface

(J9)

5V/2A

Power Jack

(CON2)

RS485_12

Transceiver &

Connector

(U9, J6)

Figure 3-1 Front View of NuMaker-IoT-MA35D1-A1

3.2 Rear View

Figure 3-2 shows the main components and connectors from the rear side of NuMaker-IoT-MA35D1-A1

board.

NuMaker-IoT-MA35D1-A1

Oct. 31, 2022 Page 10 of 43 Rev 1.01

NUMAKER-IOT-MA35D1-A1USER MANUAL

Maker Nu-mbed NUC472 User Manual

RMII1 RJ45

Connector

(CON7)

RGMII0 RJ45

Connector

(CON6)

SD1

Micro-SD

(CON5)

Arduino UNO Compatible Extension Connectors

Figure 3-2 Rear View of NuMaker-IoT-MA35D1-A1

3.3 DDR PHY and MCP DRAM Power Voltage

DDR PHY and MCP DRAM Power Selection Resistors (R252 and R253): These two resistors

R252 and R253 can decide the power voltage (1.35V or 1.8V) of DRAM_VDD that feeds to the

internal DDR PHY and MCP DARM of MA35D1 target chip.

Mounted on PCB

DRAM_VDD Voltage

MA35D1 PN / MCP DRAM Type

R252*1*2

1.35V

MA35D16F987C / DDR3L*2

R253*1

1.8V

MA35D16F787C / DDR2

Note *1: Only one resistor R252 or R253 can be mounted on the PCB and user should make sure

which part number chip of MA35D1 series that be mounted on the this NuMaker-IoT-MA35D1-A1

board.

Note *2: By default, only R252 resistor and MA35D16F987C target chip are mounted on the NuMaker-

IoT-MA35D1-A1 board.

Table 3-1 DDR PHY and MCP DRAM Power Voltage Selection

3.4 Audio Codec

Audio Codec Device (U18): Nuvoton NAU88C22 is audio codec device that integrates microphone

input, speaker output and headphone output for audio application on this board.

Headset Jack (CON8): A headset input jack that follows CTIA definition.

Speaker Connector (J7): To connect a speaker to output audio sound.

Microphone (M1): An on-board microphone for audio sound input.

3.5 RGMII Gigabit Ethernet

RGMII0 Gigabit PHY (U14) and Transformer (U15): The RGMII0 MAC of MA35D1 series needs

an external Gigabit PHY (RTL8211FDI) and a transformer (GST5009BM) to connect with the

Ethernet network.

RGMII0 RJ45 Connector (CON6): The Ethernet RGMII0 RJ45 connector.

Otros manuales para NuMicro NuMaker-IoT-MA35D1-A1

Tabla de contenidos

Otros manuales de Placa madre de Nuvoton

Nuvoton

Nuvoton NuMicro 8051 Series Manual de usuario

Nuvoton

Nuvoton NuMicro series Manual de usuario

Nuvoton

Nuvoton NuMicro series Manual de usuario

Nuvoton

Nuvoton NuMaker-M471R1 Manual de usuario

Nuvoton

Nuvoton NuMicro NuMaker-M463KG Manual de usuario

Nuvoton

Nuvoton NuMaker-M2354 Manual de usuario

Nuvoton

Nuvoton NuMicro NuGang Manual de usuario

Nuvoton

Nuvoton NuMicro NUC200 Series Manual de usuario

Nuvoton

Nuvoton NuMaker-HMI-M032K Manual de usuario

Nuvoton

Nuvoton NuMaker-M258KG Manual de usuario

Nuvoton

Nuvoton NuMaker N9H26K Series Manual de usuario

Nuvoton

Nuvoton NuMicro NuMaker-IIoT-NUC980G2D Manual de usuario

Nuvoton

Nuvoton NuMicro NuMaker-NUC029L Manual de usuario

Nuvoton

Nuvoton NuMaker NUC980 Manual de usuario

Nuvoton

Nuvoton NuDesign HMI-N9H26 Manual de usuario

Nuvoton

Nuvoton NuMicro NuMaker-NUC029SGE Manual de usuario

Nuvoton

Nuvoton NuMicro NuTiny-SDK-NANO100 Manual de usuario

Nuvoton

Nuvoton NuMicro NuMaker-M256SD Manual de usuario

Nuvoton

Nuvoton NUC900 Series Manual de usuario

Nuvoton

Nuvoton NuMaker-HMI-N9H30 Manual de usuario

Nuvoton

Nuvoton ISP/ICP 2-in-1 Programmer Manual de usuario

Nuvoton

Nuvoton NuTiny-SDK-M058S Manual de usuario

Nuvoton

Nuvoton NuMaker-M029GGC Manual de usuario

Nuvoton

Nuvoton NuMicro series Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario