Numatic HT 1840 Manual de usuario

Warning! Read instructions before using the machine

Original Instructions

TT 1840G

HT 1840

SCRUBBER DRYER

www.numatic.co.uk

Machine Overview

810

112

1 Operator control panel 12 Vacuum hose

2On / O󰀨 Lever 13 Separator

3 Waste water tank 14 Clean-water ller cap

4 Clean water tank 15 Clean-water level indicator

5Brush deck 16 Clean-water tank ll point

6Squeegee blades 17 Top tank (waste water) drainage hose

7 Floor-tool retaining knobs 18 On / O󰀨 Switch

8Clean-water on / o󰀨 tap 19 Vacuum Switch

9 Clean-water emptying cap 20 Pump Switch

10 Rear moving wheels 21 Power Light

11 Floor-tool vacuum hose 22 Handle Position lever

Fill using a hose, bucket or a suitable container. (Fig 5).

Please read before commencing any operation.

After the removal of all the packaging, carefully open and check the contents. !

Using the handle position lever, move the handle into the

upright position. (Fig 1).

Fit the Brush / Pad (Fig 2).

Swing the oor tool carrier from

behind the brush. (Fig 3).

Use the two locking knobs tted to the oor tool, secure to the

oor tool to the oor tool carrier. (Fig 4).

Fill the clean-water tank to a Max of 18 litres

(see page 5)

For operation and cleaning controls

(see page 9)

Quick Set-Up Guide

Tip the machine.

(see Page 4)

Machine Set-Up

Fitting the brushes

Slide the brush / pad under the brush deck (Fig 6).

Featuring the Nulock brush system.

The brush is tted simply by pushing and twisting to lock in place, making tting and removal a simple process.

Fit the brush / pad onto the Nulock drive chuck, twist to lock

the brush / pad in place (Fig 7).

Only use manufacturer supplied brushes.

This machine requires a 400mm brush or a 360mm pad.

Safety gloves are recommended for the changing of used brushes.

Tipping the Machine

Note: Great care must be taken to ensure that contaminants (leaves,hair, dirt, etc)

are not allowed to enter the clean-water tank during the lling process.

If using a bucket or similar, ensure it is always clean and free from debris.

Machine Set-Up

Fitting the Floor Tool

The oor tool has been designed for quick tting, allowing easy squeegee blade replacement and a safety knock-o󰀨

feature if the oor tool gets snagged, whilst in transit.

Note: It is easier to t the oor-tool if the weight of the machine is resting on the brush.

Ensure the brush is tted rst.

Note: The lever moves upward and backward motion to lock the oortool in the raised position.

The oor tool carrier can be

raised and locked from moving

by operating the locking lever,

upwards and backwards.

This lever can be found next to

the lower section of the handle.

Unlock and swing the oor tool

carrier to the side of the machine

(Fig 8).

Filling the clean-water tank

The HT1840 & TT1840 are

equipped with a large 18 litre

clean water tank allowing large

areas to be cleaning in a single

ll.

To ll the clean water tank,

remove the ller cap (Fig 10).

Fill using a hose, bucket or a

suitable container. (Fig 11).

Secure to the carrier using the

two knobs tted to the oor tool

carrier (Fig 9) - (Fig 9a).

Do not over tighten the retaining

knobs.

Control of Substances Hazardous to Health (COSHH)

For best results use a non-foaming type of chemical, dilute to the manufacturer’s specication.

For further guidance on hazardous substances refer to health and safety instructions online.

Visit http://www.hse.gov.uk/ for UK information.

Water Flow Adjustment

Located on the left of the machine is the On / O󰀨 water tap

(Fig 14 / 15).

Pre-cleaning advice.

Important

Do not operate machine unless the Operator Manual has been read and fully understood.

Before performing the cleaning operation, place out

appropriate warning signs and sweep or dust-mop the oor (Fig 16).

WHEN HANDLING AND MIXING CHEMICALS

Always ensure that chemical manufacturer’s safety guidelines are followed.

Only use chemicals recommended for use in auto scrubber-dryers.

Numatic part (629044) Wet Floor sign

(available if required)

Machine Set-Up

Fill Level Indicator

Fill the clean water tank to a maximum of 18 litres, including cleaning chemicals if required.

Follow chemical manufacturing guide lines.

Use the ll indicator

(Fig 12). Showing the clean water tank full

(Fig 13a).

Showing the clean water tank empty

(Fig 13).

13a

Moving the machine

CAUTION

When moving or lifting the HT 1840 / TT 1840, follow the national safety guidelines on lifting.

! !

When the bottom tank (clean water) is full the machine can be

tilted to a maximum of 450(Fig 19).

When the top tank (waste water) is full the machine can be

tilted to a maximum of 100 for transporting to dumping area

(Fig 18).

CAUTION

Ensure both tanks are empty before attempting to lift the machine.

! !

Transport the machine by tilting back on to the main transit

wheels (Fig 17).

Weight of empty machine 38.5Kg (85 lbs) (Fig 20).

Machine Set-Up

Note: Care must be taken to reduce speed when cornering or when manoeuvring around obstacles.

Note: The lever moves upward and backward motion to lock the oor tool in the raised position.

Machine Operation

Pre-scrub mode

The HT1840 & TT1840 have been designed to cope with a variety of oor types and di󰀨erent levels of soiling.

On heavily soiled oors use a ‘double scrub’ technique.

First pre-scrub the oor with the oor tool in the raised position (Fig 21), allow the chemical time to work, then scrub

the area a second time with the oor tool lowered.

To raise the oor-tool, ensure the oor tool carrier is central to the machine (Fig 22).

Lift the lever near the base of the handle and lock into position (Fig 23).

The clean-water / chemical mix

is dispersed via ‘THRU-FEED’

system. The waste water is then

retrieved by the oor tool

Overlap the scrubbing path by

10cm to ensure an even clean

(Fig 24).

If streaking occurs, wipe the oor

tool blades clean (Fig 25).

Floor tool in use

Setting the cleaning controls

Note: The Pump Switch will only function when the Brush is in operation.

Ensure your HT1840 / TT1840 machine has been plugged into a suitable power supply.

Select the desired function using the ON / OFF switches tted to the handle.

Vac Switch Pump Switch

1 1

To start: hold down either trigger and press the yellow start button once

20.020.0

ST_Numatic_A4.slddrt 20030224

THIS DRAWING IS COPYRIGHT AND IS THE PROPERTY OF NUMATIC INTERNATIONAL LTD. AND MUST

NOT BE USED WITHOUT THEIR KNOWLEDGE NOR COMMUNICATED TO ANY PERSON OR COMPANY.

TITLE:-

DIMNs IN

MILLIMETERS

NOT

SCALE

FINISH:-

ITEM No(s):-

DRG No:-

TOLERANCES:-

(UNLESS OTHERWISE STATED)

DRAWN:

DATE:

APPD:

REVISION:

CHANGE DETAIL:

Numatic

INTERNATIONAL LTD

THIRD ANGLE PROJECTION

STRESS RELEIF ARTWORK ASM

RVT

MATERIAL:-

27/05/2009

DRW-21826

SIZE

LINEAR: 0 DECIMAL PLACE = +/- 1.0mm

1 DECIMAL PLACE = +/- 0.25mm

2 DECIMAL PLACES = +/- 0.05mm

ANGULAR:-

+/- 0.5 DEGREE

THE EXAMPLE SHOWN DETAILS THE METHOD USED FOR

IDENTIFYING CRITICAL (INSPECTION) DIMENSIONS WHERE APPLICABLE

MILLFIELD ROAD, CHARD, SOMERSET

TA20 2GB ENGLAND

A01

TOOL NUMBER:

WEIGHT:

All components must be ROHS compliant.

Internal Code:

DEV

Provisional

20.020.0

ST_Numatic_A4.slddrt 20030224

THIS DRAWING IS COPYRIGHT AND IS THE PROPERTY OF NUMATIC INTERNATIONAL LTD. AND MUST

NOT BE USED WITHOUT THEIR KNOWLEDGE NOR COMMUNICATED TO ANY PERSON OR COMPANY.

TITLE:-

DIMNs IN

MILLIMETERS

NOT

SCALE

FINISH:-

ITEM No(s):-

DRG No:-

TOLERANCES:-

(UNLESS OTHERWISE STATED)

DRAWN:

DATE:

APPD:

REVISION:

CHANGE DETAIL:

Numatic

INTERNATIONAL LTD

THIRD ANGLE PROJECTION

STRESS RELEIF ARTWORK ASM

RVT

MATERIAL:-

27/05/2009

DRW-21826

SIZE

LINEAR: 0 DECIMAL PLACE = +/- 1.0mm

1 DECIMAL PLACE = +/- 0.25mm

2 DECIMAL PLACES = +/- 0.05mm

ANGULAR:-

+/- 0.5 DEGREE

THE EXAMPLE SHOWN DETAILS THE METHOD USED FOR

IDENTIFYING CRITICAL (INSPECTION) DIMENSIONS WHERE APPLICABLE

MILLFIELD ROAD, CHARD, SOMERSET

TA20 2GB ENGLAND

A01

TOOL NUMBER:

WEIGHT:

All components must be ROHS compliant.

Internal Code:

DEV

Provisional

ALWAYS ENSURE THAT THE POWER SUPPLY IS DISCONNECTED,

PRIOR TO ANY MAINTENANCE OPERATION.

! !

After use, empty waste water tank using

emptying hose and ush out with clean

water. A

Remove the two hoses and disconnect the

separator from the machine (Fig 26). Undo

the separator restraining strap (Fig 26a) and

lift o󰀨 the separator. The separator has a

sealing rubber which should be examined at

every clean down (Fig 27).

Rinse using clean water.

Note:

Avoid over tightening the clean water draining cap.

The HT1840 & TT1840 have been designed with ease of use in mind, this included easy stripping down and cleaning.

Remove the two lters clipped into the separator and ush with clean water (Fig 28)(Fig 29).

Replace by tting the rear of the lter rst then clipping the front to lock in place (Fig 30) (Fig 31).

Once emptied the top waste water tank can simply be lifted o󰀨. (Fig 32).

The clean water tank can be drained via the yellow cap tted to the left

hand side of the machine. The cap has a rubber seal and might require a

spanner to remove. (Fig 33).

Regular Maintenance

26a

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Secadora de Numatic

Numatic

Numatic TTV-5565/200T Manual de usuario

Numatic

Numatic CRL8055/100T Manual de usuario

Numatic

Numatic ttb 6652 100T Guía

Numatic

Numatic TTV 678-300 Instrucciones de montaje

Numatic

Numatic HBG 3045 Manual de usuario

Numatic

Numatic NX300 Manual de usuario

Numatic

Numatic TBL6055/100 Manual de usuario

Numatic

Numatic TTB 1840G Manual de usuario

Numatic

Numatic TTV - 4555/100T Manual de usuario

Numatic

Numatic CRG 8055/100T Manual de usuario

Numatic

Numatic CRG 8055/100T Manual de usuario

Manuales populares de Secadora de otras marcas

Bosch

Bosch WTA79200GB Manual de usuario

Amana

Amana W10233410A Manual de usuario

Miele

Miele TWH 780 WP Manual de usuario

Asko

Asko T760 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Manual de usuario

Bosch

Bosch Logixx 10 WTB76556GB Hoja de especificaciones

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Manual de instrucciones

Electrolux

Electrolux EW2H328R2 Manual de usuario

Beko

Beko DS8433RX1M Manual de usuario

Dawlance

Dawlance Spinner DS 6000 C Manual de usuario

Electrolux

Electrolux TP5080TW Manual de usuario

AEG

AEG TR838P4OB Manual de usuario

Indesit

Indesit IDV 75 Manual de usuario

Infiniton

Infiniton SD-DG85C Manual de usuario

BOMANN

BOMANN WT 5019 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Manual de usuario

Asko

Asko T793C Manual de usuario

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manual de usuario