Numark NS7II Manual de usuario

User Guide

English ( 3 – 14 )

Guía del usuario

Español ( 15 – 26 )

Guide d'utilisation

Français ( 27 – 38 )

Guida per l'uso

Italiano ( 39 – 50 )

Benutzerhandbuch

Deutsch ( 51 – 62 )

Appendix

English ( 63 )

User Guide (English)

Introduction

Box Contents

•NS7II

•2 Platter Assemblies:

oAluminum Platter

oSlipmat

oVinyl

o45 RPM Adapter (attached)

•IEC Power Cable

•USB Cable

•Spindle Screw

•Allen Wrench

•Serato DJ software (download)

•Quickstart Guide

•User Guide

•Safety & Warranty Manual

Product Registration and Support

For the latest information about this product (system requirements, compatibility information, etc.) and

product registration, visit numark.com/ns7ii.

For additional product support, visit numark.com/support.

Quick Start

BEFORE GETTING STARTED:

•Read the Safety & Warranty Manual before using the NS7II.

•Make sure all items listed in the Box Contents are included.

1. Assemble the Platters

1. Remove the NS7II from the packaging. Remove the two

platter assemblies from package (underneath the NS7II

controller). Place the NS7II is on a flat, stable surface for

operation. Ensure unit has adequate air flow to all ventilation

ports (especially if installed in a case).

2. Place the platter onto the NS7II by aligning the pins in the

bottom of the platter with the holes in the NS7II's motor.

3. Place the slipmat onto the platter, then place the vinyl over

the slipmat.

4. Line up the notch in the spindle with the screw in the vinyl's 45 RPM

Adapter. Use the allen wrench (included) to tighten the screw, locking

the adapter to the spindle.

Step 4

Step 2 Step 3

2. Install the Drivers and Software

IMPORTANT: Install the drivers before installing the software.

Drivers: Download and install the latest drivers from numark.com/ns7ii. (You will be asked to

connect the NS7II to your computer during installation.)

Software: Download and install the latest version of Serato DJ from serato.com.

3. Connect and Start DJing!

Follow this sequence of steps whenever you use NS7II:

1. Make sure all devices are off and all faders and gain knobs are set to "zero."

2. Connect input sources (microphones, turntables, CD players, etc.) to the NS7II.

3. Connect output devices (power amplifiers, sub-mixer, recorders, etc.) to the NS7II.

4. Plug all devices into power sources, and turn on devices in proper order:

•When starting a session, turn on (1) input sources, (2) NS7II, (3) output devices.

•When ending a session, turn off (1) output devices, (2) NS7II, (3) input sources.

5. Connect the NS7II to your computer with the USB cable (included) and to your headphones.

6. Open Serato DJ and go! For more information on how to use Serato DJ with NS7II, visit

serato.com/dj/support and select Numark NS7II.

Connection Diagram (example):

00.0%

Any items shown here but not mentioned in the Box Contents are sold separately.

Headphones

(to front panel)

Turntable

Computer

Tablet, MP3 player, etc.

Power

Microphone

(to front panel)

Powered Loudspeakers

Features

Top Panel

16 16

26 27 28 29 30

31 31

33 35

3636

3838

3939 39

26 27 28 29 30

17 17

18 18

4142

53 53 53 53

54 54 54 54

50 50 50 52

49 49 49

50 50 50 52

49 49

47 46

44 45

15 14

33 33

Useful Terms:

Audio Pointer: The current position in a track from where audio will play. When you select a track

and begin playing, the Audio Pointer will usually start from the beginning and stop at the end.

Hot Cue Point: A marked position in a track, which will be permanently stored by the software.

You can set, return to, or delete Hot Cue Points with the Hot Cue Buttons.

Temporary Cue Point: A marked position in a track, which will only remain while that track is still

loaded in the Deck. You can set and return to the Temporary Cue Point with the Cue button.

General Controls

1. Shift: Press and hold this button to access secondary functions (in red lettering) of other

controls on NS7II.

2. Touch Mode: Press and hold this button to activate Touch Mode, which lets you access the

touch-capacitive functions of NS7II's FX 1 Knob, FX 2 Knob, and FX 3 Knob.

Press and hold Shift and then press this button to access the touch-capacitive functions of

the same knobs as above plus the EQ Knobs (Channel Treble, Channel Mid, and Channel

Bass). These functions are momentary, not "latching."

3. Layer: Selects which Layer in the software is controlled by that hardware Deck. Deck A can

control Layer 1 or 3; Deck B can control Layer 2 or 4.

4. USB Indicator: This LED lights up when NS7II is successfully connected to and

communicating with your computer.

Mixer Controls

5. Input Selector: Set this switch to the desired audio source from this channel: PC (a track

playing on that layer in the software), Mic 2 or Line (a device connected to the Mic 2 Input or

Line Input on NS7II's rear panel). Please note that the Line/Phono selector switches on

NS7II's rear panel must also be set properly. Also, a channel's controls will only send MIDI

information when its Input Selector is set to PC.

Important: Do not set more than one channel's Input Selectors to Mic2; doing so can cause

unwanted feedback or distortion.

6. Gain Trim: Adjusts the pre-fader, pre-EQ audio level of the corresponding channel in the

software.

7. LED Meters: Monitors the audio levels of the corresponding channel.

8. Channel Treble: Adjusts the high (treble) frequencies. When Touch Mode is activated,

touching this knob will mute the corresponding channel's high frequencies (an "EQ kill").

9. Channel Mid: Adjusts the mid-range frequencies. When Touch Mode is activated, touching

this knob will mute the corresponding channel's mid-range frequencies (an "EQ kill").

10. Channel Bass: Adjusts the low (bass) frequencies. When Touch Mode is activated, touching

this knob will mute the corresponding channel's low frequencies (an "EQ kill").

11. Channel Fader: Adjusts the audio level on the corresponding channel in the software.

12. PFL: Press this button to send this channel's pre-fader signal to the Cue Channel for

monitoring. When engaged, the button will be lit. By pressing one PFL button at a time, you

will cue that channel alone (and deactivate PFL monitoring for the other channels). To cue to

multiple channels simultaneously, press the PFL buttons for those channels at the same

time.

13. Crossfader: Blends audio between the channels assigned to the left and right side of the

crossfader.

14. Master Volume: Adjusts the output volume of the Program Mix.

15. Booth/Zone Volume: Adjusts the output volume of the Booth Output mix.

Playback Controls

16. Platter: Controls the Audio Pointer in the software.

17. Start Time: Controls the rate at which the platter regains its normal playback speed.

18. Stop Time: Controls the rate at which the platter slows to a complete stop ("brake time").

19. Play / Pause: This button pauses or resumes playback.

Press and hold Shift and then press this button to "stutter-play" the track from the last set

Cue Point.

20. Cue: When the Deck is paused, you can set a Temporary Cue Point by moving the Platter to

place the Audio Pointer at the desired location and then pressing the Cue Button.

During playback, you can press the Cue Button to return the track to this Temporary Cue

Point. (If you did not set a Temporary Cue Point, then it will return to the beginning of the

track.)

If the Deck is paused, you can press and hold the Cue Button to play the track from the

Temporary Cue Point. Releasing the Cue Button will return the track to the Temporary Cue

Point and pause it. To continue playback without returning to the Temporary Cue Point, press

and hold the Cue Button, then press and hold the Play Button, and then release both buttons.

Press and hold Shift and then press this button to return to the beginning of the track.

21. Sync: Press this button to automatically match the corresponding Deck's tempo with the

opposite Deck's tempo and phase. Press and hold Shift and press this button to deactivate

Sync.

22. Bleep / Reverse: Reverses audio playback of the track on the corresponding deck.

When the switch is in the Reverse position, the playback of the track will be reversed.

Returning the switch to its center (deactivated) position will resume normal playback from

wherever the Audio Pointer stops.

When the switch is in the Bleep position, the playback of the track will be reversed. Returning

the switch to its center (deactivated) position will resume normal playback from where it

would have been if you had never engaged the Bleep function (i.e., as if the track had been

playing forward the whole time).

Cue Controls

23. Hot Cue Buttons (1-5): Assigns a Hot Cue Point or returns the track to that Hot Cue Point.

When a Hot Cue Button is unlit, you can assign a Hot Cue Point by pressing it at the desired

point in your track. Once it is assigned, the Hot Cue Button will light. To return to that Hot

Cue Point, simply press it.

Press and hold Shift and then press a Hot Cue Button to delete its assigned Hot Cue Point.

Tip: If the Deck is paused, holding a lit Hot Cue Button will start playback from that Hot Cue

Point. Releasing it will return the track to that Hot Cue Point and pause playback.

Pad Mode Controls

24. Pads: These pads have different functions

on each Deck depending on the current Pad

Mode. These pads are the same pads used

with Akai Professional MPCs, so they are

velocity-sensitive (in certain modes only),

durable, and easy to play.

In this section, when referring to specific

pads, it will refer to the numbers as shown in

the diagram on the right.

25. Parameter < / > : Use these buttons for various functions in each Pad Mode (described

below).

1234

5678

26. Cues: This Pad Mode button switches the pads between two modes: Hot Cue Mode (red)

and Hot Cue Auto-Loop Mode (orange). When the button is unlit, the first press will always

select Hot Cue Mode.

•Hot Cue Mode: Each pad assigns a Hot

Cue Point or returns the track to that Hot

Cue Point. (Pads 1-5 are essentially

duplicates of Hot Cue Buttons 1-5).

When a Hot Cue Button is unlit, you can

assign a Hot Cue Point by pressing it at

the desired point in your track. Once it is

assigned, the Hot Cue Button will light.

Press and hold Shift and then press a

pad to delete its assigned Hot Cue Point.

•Hot Cue Auto-Loop Mode: Each pad

assigns a Hot Cue Point or returns the

track to that Hot Cue Point, but in both

cases, it also creates an Auto-Loop at

that point. The Auto-Loops length is set

in the software, but you can decrease or

increase it with the Parameter < or

Parameter > button.

27. Auto / Roll: This Pad Mode button puts the pads in two modes: Auto-Loop Mode (dark blue)

and Loop Roll Mode (light blue). When the button is unlit, the first press will always select

Auto-Loop Mode.

Note: The pad layouts here match the software's default Auto-Loop time division layout. If

you shift the range of time divisions displayed in the software, the pad layout will change to

match it.

•Auto-Loop Mode: Each pad triggers or

releases an Auto-Loop of a different

length. Press and hold Shift and then

press the Parameter < or Parameter >

button to shift the Auto-Loop backward

or forward.

•Loop Roll Mode: Each pad triggers a

momentary Loop Roll. Press the

Parameter < or Parameter > button to

change the Loop Roll's time division.

Hot Cue 1

Hot Cue 2

Hot Cue 3

Hot Cue 4

Hot Cue 5

Hot Cue 6

Hot Cue 7

Hot Cue 8

Hot Cue 1 +

Auto-Loop

Hot Cue 2 +

Auto-Loop

Hot Cue 3 +

Auto-Loop

Hot Cue 4 +

Auto-Loop

Hot Cue 5 +

Auto-Loop

Hot Cue 6 +

Auto-Loop

Hot Cue 7 +

Auto-Loop

Hot Cue 8 +

Auto-Loop

1/8-beat

Auto-Loop

1/4-beat

Auto-Loop

1/2-beat

Auto-Loop

1-beat

Auto-Loop

2-beat

Auto-Loop

4-beat

Auto-Loop

8-beat

Auto-Loop

16-beat

Auto-Loop

1/8-beat

Loop Roll

1/4-beat

Loop Roll

1/2-beat

Loop Roll

1-beat

Loop Roll

2-beat

Loop Roll

4-beat

Loop Roll

8-beat

Loop Roll

16-beat

Loop Roll

28. Loop: This Pad Mode button switches the pads between two banks in Manual Loop Mode.

When the button is unlit, the first press will always select the first bank.

•Manual Loop Mode: Pads 1-4 (the top

row) return the track to one of your

saved Manual Loops. You set and

assign a Manual Loop using Pads 5-8

(the bottom row). The pad layouts for

the two banks are identical.

To set a Manual Loop, press any one

of Pads 1-4 (the top row) that does not

have a Manual Loop assigned to it. Press Pad 5 to set the Loop In Point, and then press

Pad 6 to set the Loop Out Point and trigger the loop.

To trigger an assigned Manual Loop, press any one of Pads 1-4 (the top row) that

has a Manual Loop assigned to it. You can use Pad 7 to activate or deactivate the loop.

Press Pad 8 to return the track to the last triggered Manual Loop and activate it

("reloop").

To delete a Manual Loop, press and hold Shift and then press the corresponding pad

(of Pads 1-4).

Press the Parameter < or Parameter > button to halve or double the Manual Loop's

length. Press and hold Shift and then press the Parameter < or Parameter > button to

shift the Manual Loop backward or forward.

29. Sampler: This Pad Mode button switches the pads between two modes: Sample Player

Mode and Sample Velocity Trigger Mode). When the button is unlit, the first press will always

select Sample Player Mode.

•Sample Player Mode: Pads 1-6 each

trigger a sample, which you can assign

in the software (the volume level is also

set in the software). Unlit pads have no

sample assigned to them. Violet pads

have a sample assigned but are not

triggered. Magenta pads have a sample

assigned and are currently playing.

•Sample Velocity Trigger Mode: The pads behave identically to the pads in Sample

Player Mode, except they are velocity-sensitive, so triggered samples will play back at a

volume level proportional to how heavily you pressed the pads. This mode can give your

performance more of a "human feel."

Manual

Loop 1

(or 5)

Manual

Loop 2

(or 6)

Manual

Loop 3

(or 7)

Manual

Loop 4

(or 8)

Set

Loop In

Set

Loop Out

Loop

On/Off Reloop

Sample 1 Sample 2 Sample 3

Sample 5 Sample 6 no function

Sample 4

no function

30. Slicer: This Pad Mode button switches the pads between two modes: Slicer Mode and Slicer

Loop Mode. When the button is unlit, the first press will always select Slicer Mode.

Important: Your track must have a set Beat Grid for Slicer Mode or Slicer Loop Mode to

work.

•Slicer Mode: The eight pads represent

eight sequential beats—"Slices"—in the

Beat Grid. The currently playing Slice is

represented by the currently lit pad; the

light will "move through the pads" as it

progresses through each eight-Slice

phrase. Press a pad to play that Slice—

hold it down if you want to keep looping

it. When you release the pad, the track will resume normal playback from where it would

have been if you had never pressed it (i.e., as if the track had been playing forward the

whole time).

Press the Parameter < or Parameter > button to decrease or increase the Slice

quantization. Press and hold Shift and then press the Parameter < or Parameter >

button to decrease or increase the Slice Domain size.

•Slicer Loop Mode: The pads behave identically to the pads in Slicer Mode, except the

eight-Slice phrase will loop rather than moving forward continuously through the track.

Track Controls

31. Strip Search™: The length of this strip represents the length of the entire track. Place your

finger on a point along this sensor to jump to that point in the track. (If you want to scroll

through a track, we recommend using your computer rather than running your finger along

the strip.)

32. Slip / Clear: When using the software's Beat Grid, press and hold this button and move the

Platter to "slip" (i.e., shift or slide) the entire Beat Grid to the left or right.

Press and hold Shift and then press this button to delete the entire Beat Grid.

Important: Your track must have a set Beat Grid for the Slip / Clear button to work.

33. Adjust / Set: Press and hold this button and move the Platter to "warp" the entire Beat Grid.

Press and hold Shift and then press this button to set a Beat Marker at the Audio Pointer's

current location.

Important: Your track must have a set Beat Grid for the Adjust feature to work. Also, using

the Adjust feature will change the track's BPM.

34. Slip Mode / Motor Off: Press this button to enable or disable Slip Mode. In Slip Mode, you

can jump to Hot Cue Points, trigger Loop Rolls, or use the Platters, while the track's timeline

continues. In other words, when you stop the action, the track will resume normal playback

from where it would have been if you had never done anything (i.e., as if the track had been

playing forward the whole time).

Press and hold Shift and press this button to activate or deactivate the corresponding

Platter's motor. This will not affect the track's playback.

Slice 1 Slice 2 Slice 3 Slice 4

Slice 5 Slice 6 Slice 7 Slice 8

Otros manuales para NS7II

Tabla de contenidos

Idiomas:

Otros manuales de Equipo de DJ de Numark

Numark

Numark NS7III Manual de usuario

Numark

Numark PT01 Scratch Manual de usuario

Numark

Numark NVII Manual de usuario

Numark

Numark MIXDECK Guía de instalación

Numark

Numark NuVJ Manual de usuario

Numark

Numark Mixtrack Quad Manual de usuario

Numark

Numark 4TRAK Manual de usuario

Numark

Numark NDX 800 Manual del operador

Numark

Numark Mixtrack pro II Manual de usuario

Numark

Numark NS6 II Manual de usuario

Numark

Numark DJ2Go2 Manual de usuario

Numark

Numark PARTY MIX Manual de usuario

Numark

Numark Mixtrack Pro Manual de usuario

Numark

Numark MIXTRACK PLATINUM Manual de usuario

Numark

Numark iDJ3 Manual de usuario

Numark

Numark OMNI CONTROL Manual de instrucciones

Numark

Numark NS6 Manual de usuario

Numark

Numark BCM135 Manual de usuario

Numark

Numark DDS Manual de usuario

Numark

Numark DDS80 Manual de usuario

Numark

Numark FUSION 111 Manual de usuario

Numark

Numark NS6 Manual de usuario

Numark

Numark UPM Manual de usuario

Numark

Numark CDN-88 Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario