Numark NDX500 Manual de usuario

VirtualDJ 8 –Numark NDX500

Table of Contents

Installation................................................................................................................................3

Connections ...........................................................................................................................3

Firmware & Drivers ................................................................................................................3

VirtualDJ 8 Setup ...................................................................................................................4

Advanced Setup.....................................................................................................................5

Layout........................................................................................................................................6

Operation..................................................................................................................................7

Useful Links............................................................................................................................11

VirtualDJ 8 –Numark NDX500

Installation

Connections

Connect the NDX500 with a USB port of

your computer using the provided USB

cable.

Use a pair of RCA cables to connect each

NDX Output to an Input Channel of a

mixer. Any analogue or digital mixer can

be used.

Connect your amplifier or amplified

speakers to the Master Output of a mixer

Power on the NDX500 your mixer and

your amplifier.

Set the NDX500 to MIDI mode using the

SOURCE buttons.

Firmware & Drivers

No drivers are required to be installed for the NDX500. The NDX500 is a USB class-

compliant and your Operation system (Windows or Mac) will auto-install the necessary

drivers and will auto-detect the NDX500 as a Midi device with built-in Audio interface.

Check Numark webpage of any firmware update and make sure your units run the very last

version.

http://www.numark.com/product/ndx500

VirtualDJ 8 –Numark NDX500

VirtualDJ 8 Setup

Download and install VirtualDJ 8 from

http://www.virtualdj.com/download/index.html

(in case you have not done already)

Once VirtualDJ 8 is launched, a Login

Window will appear. Login with your

virtualdj.com account.

A Pro Infinity, a PLUS Controller or a

Subscription License is required to use the

Numark NDX500 with VirtualDJ 8

Without any of the above Licenses, the

controller will operate for 10 minutes each

time you restart VirtualDJ 8.

http://www.virtualdj.com/buy/index.html

Launch VirtualDJ 8

A detection window will appear

verifying the proper connection.

Click on the Use Soundcard button to

allow VirtualDJ to automatically create

the necessary Audio configuration.

Click OK.

The unit is now ready to operate.

VirtualDJ 8 –Numark NDX500

Advanced Setup

MIDI Operation

The unit should be visible in the

CONTROLLERS tab of Config and the

“factory default” available/selected from

the Mappings drop-down list.

The factory default Mapping offers the

functions described in this Manual,

however those can be adjusted to your

needs via VDJ Script actions.

Note. Each NDX500 unit (if more than 1 is

connected) will be additionally displayed in

this window, and any modifications in the

mapping file will affect all units.

Find more details at

http://www.virtualdj.com/wiki/VDJscript.html

AUDIO Setup

The unit has a pre-defined Audio setup and

a special button in the AUDIO tab of Config

to provide that.

Please read the manual of the unit for further connections/capabilities and setups.

http://www.numark.com/images/product_downloads/NDX500-UserGuide-v1.1.pdf

For further VirtualDJ settings and features please refer to the User Guides of VirtualDJ 8.

http://www.virtualdj.com/wiki/PDFManuals.html

VirtualDJ 8 –Numark NDX500

Layout

VirtualDJ 8 –Numark NDX500

Operation

M. SOURCE. Use this button to cycle through the available Operation modes of the

Numark NDX500 (CD, USB and MIDI).

If both Leds are on, the unit is set to MIDI mode and can control a VirtualDJ

deck. Notice that the unit will still be detected as a MIDI and Audio device if the CD

or USB modes are selected, however it will not control any VirtualDJ operation.

S. SHIFT. (BRAKE) Press and hold this button to access secondary functions of other

controls on the NDX500.

1. PLAY. Plays / Pauses the track.

2. CUE. When the Deck is paused, you can set a temporary Cue Point by moving the

Platter to place the Audio Pointer at the desired location and then pressing the Cue

Button.

During playback, you can press the Cue Button to return the track to this Cue

Point. (If you did not set a Cue Point, then it will return to the beginning of the track.).

If the Deck is paused, you can press and hold the Cue Button to play the track from

the Temporary Cue Point. Releasing the Cue Button will return the track to the

temporary Cue Point and pause it. To continue playback without returning to the

Temporary Cue Point, press and hold the Cue Button, then press and hold the Play

Button, and then release both buttons.

3. TAP. If the track is paused, use this button to set the 1st beat of the 4-bar Beatgrid to

the current position. If track is playing, tap at least 4 times based on the tempo of the

track to manually calculate the tempo and the beat phase of the track (if VirtualDJ

has not calculated it correctly).

Hold SHIFT down and then use this button to synchronize the tempo and the beat-

phase of this track to the opposite (or Master) deck’s track.

4. TRACK. Use this encoder to scroll through files or Folders. If focus is on the

Folders list, push the encoder to set focus to the Songs list. If focus is on Songs

List or Sideview, push the encoder to load the selected track to the deck.

Hold SHIFT down and then use the encoder to cycle through the available views of

the Sideview (Automix, Sidelist, Karaoke, Sampler and Shortcuts).

Hold SHIFT down and then push the encoder to cycle through the Browser

windows (Folders, Songs and SideView).

5. FOLDER. Use this button to set focus to the Folders list. If focus is on the Folders

list, use this button to open/close subfolders.

6. EJECT. Not used. This button selects one of the 4 available MIDI channels of the

NDX500. Regardless of the selected MIDI Channel, the NDX500 will still control the

assigned VirtualDJ deck.

VirtualDJ 8 –Numark NDX500

7. USB socket. Connect a USB Flash Drive. Its files will be used when the NDX500 is

on USB mode.

8. LCD. The LCD screen will show all the Track’s and VirtualDJ Deck information, such

as Elapsed/Remain/total times, BPM and pitch, Title, Artist and Album, Play status,

assigned Deck number etc.

9. TIME. Use this button to cycle through the available Time Display modes (Remain,

Elapsed and Total). Each time a Display mode is selected the Time and the mode

will be displayed on the LCD screen, and the progress bar will be also adjusted to the

selected mode.

10. SINGLE. Use this button to enable/disable Automix. An indicator (CONTINUE) will

be displayed on the LCD screen if Automix is enabled.

11. PROG. Use this button to cycle through the 4 available Text modes on the LCD

screen (Title, title-Artist, Artist and Album)

Hold SHIFT down and then use this button to assign a different VirtualDJ deck to

this unit. The number of the assigned deck will be displayed on the LCD screen. The

number of the available VirtualDJ decks along with the possible assigned deck on

each unit, depends on the total number of the deck son the used GUI or the total

number that the connected units can control. Manually assign of a VirtualDJ deck can

be made from the Controllers tab of the VirtualDJ Settings window.

By default, if 2 NDX500 are connected and a 4 decks skin is used, the left unit will be

assigned to deck 1 and will toggle between decks 1 and 3, and the right unit will be

automatically assigned to deck 2 and will toggle between decks 2 and 4.

12. LOOP IN. Use this button to set the Entry point of a manual loop. If a loop is

triggered/enabled, use this button to set the Jogwheel to Loop In mode (led will

flash) and then use the Jogwheel to fine-adjust the Loop In point.

Hold SHIFT down and then use this button to half the size of the selected loop.

13. LOOP OUT. Use this button to set the Exit point of a manual loop. If a loop is

triggered/enabled, use this button to set the Jogwheel to Loop Out mode (led will

flash) and then use the Jogwheel to fine-adjust the Loop Out point.

Hold SHIFT down and then use this button to double the size of the selected loop..

VirtualDJ 8 –Numark NDX500

14. RELOOP. Use this button to exit a manually triggered loop or trigger the last

triggered loop (re-loop)

Hold SHIFT down and then use this button to set an Auto Loop of a pre-selected

size in beats.

15. REC. Hold this button down and then press any of the HotCues buttons (16 to 18) to

delete their assigned HotCue points (leds will flash).

16. HOTCUE 1. Use this button to assign Hot Cue 1Point or returns the track to this

Hot Cue Point. When button is unlit, you can assign Hot Cue 1 by pressing it at the

desired point in your track. Once it is assigned, the Hot Cue Button will light. To

return to Hot Cue 1, simply press it.

Hold the REC button down and then use this button to delete HotCue 1

Hold SHIFT down and then use this button to trigger an Auto-Loop of 1 beat in size.

17. HOTCUE 2. Use this button to assign Hot Cue 2Point or returns the track to this

Hot Cue Point. When button is unlit, you can assign Hot Cue 2 by pressing it at the

desired point in your track. Once it is assigned, the Hot Cue Button will light. To

return to Hot Cue 2, simply press it.

Hold the REC button down and then use this button to delete HotCue 2

Hold SHIFT down and then use this button to trigger an Auto-Loop of 2 beatsin

size.

18. HOTCUE 3. Use this button to assign Hot Cue 3Point or returns the track to this

Hot Cue Point. When button is unlit, you can assign Hot Cue 3 by pressing it at the

desired point in your track. Once it is assigned, the Hot Cue Button will light. To

return to Hot Cue 3, simply press it.

Hold the REC button down and then use this button to delete HotCue 3

Hold SHIFT down and then use this button to trigger an Auto-Loop of 4 beatsin

size.

19. REVERSE. Use this button to play the track in reverse. Once disabled, the track

will continue to play at the normal direction from the current position. When Slip

mode is enabled, the track will return to the position it would have been if the reverse

was never used.

20. SCRATCH. Use this button to toggle between the CD and Vinyl Jogwheel modes.

The Led if this button will be lit if the Vinyl mode is selected.

In CD mode, use the Jogwheel to bend (temporary speed up –slow down the tempo

of the track).

In VINYL mode, use the outer part of the Jogwheel to bend (temporary speed up –

slow down the tempo of the track) and the inner touch-sensitive part to scratch.

Hold SHIFT down and then use this button to enable/disable Slip mode. When Slip

mode is enabled, several functions such as Scratching, loops, HotCues etc. will act

VirtualDJ 8 –Numark NDX500

temporary and the track will resume to the position it would have been if those

functions never used.

21. SEARCH. Hold this button to set the Jogwheel to temporary set the Jogwheel to

Search/Seek mode. While the button is held, use the Jogwheel to fast search/seek

through the track. Once released, the Jogwheel will return to its previous mode.

22. JOG. Touch sensitive jogwheel. Use the jogwheel to scratch and pitch bend (if Vinyl

mode is selected), or pitch bend (in CD mode) If the SEARCH button is pressed, use

the Jogwheel to fast search/seek through the track.

The Jogwheel also offers Loop In and Loop Out adjustment (see LOOP IN and

LOOP Out buttons)

23. MASTER TEMPO. Press this button to "lock" the track's pitch to its original key. The

track's tempo will remain at the speed designated by the Pitch Fader.

24. PITCH RANGE. Press this button to select the next available range for the Pitch

Fader (available values ±4%, ±8%, ±16% and ±100%).

The Ledsabove this button will indicate the selected pitch range.

A different Pitch range can be selected from the Deck Options in VirtualDJ GUI.

25. PITCH. Adjust the track's playback speed (tempo).

The actual pitch fader will not alter the pitch of the track if the actual pitch and the

software pitch value do not match (software soft-takeover, ghost fader visible on the

GUI). In most cases this may happen if SYNC is prior pressed or switching decks

and the other deck is having a different pitch software value.

26. PITCH BEND. Press and hold down these buttons to temporary speed up/slow

down the song while pressed. When released, the track playback will return to the

speed designated by the Pitch Fader.

Otros manuales para NDX500

Tabla de contenidos

Otros manuales de Equipo de DJ de Numark

Numark

Numark MIXSTREAM PRO Manual de usuario

Numark

Numark NS6 II Manual de usuario

Numark

Numark NS4 FX Manual de usuario

Numark

Numark iM9 Manual de usuario

Numark

Numark DJio Manual de usuario

Numark

Numark NS4 FX Manual de usuario

Numark

Numark AXIS 9 Manual de servicio

Numark

Numark M1 Guía de inicio rápido

Numark

Numark NS6 Manual de usuario

Numark

Numark cdmix usb Manual de usuario

Numark

Numark Mixtrack Pro Manual de usuario

Numark

Numark MIXDECK EXPRESS Manual de usuario

Numark

Numark iDJ3 Manual de usuario

Numark

Numark NuVJ Manual de usuario

Numark

Numark N4 Manual de usuario

Numark

Numark PARTY MIX Manual de usuario

Numark

Numark NV Manual de usuario

Numark

Numark DDS Manual de usuario

Numark

Numark MIXDECX QUARD Manual de usuario

Numark

Numark NDX500 Manual de usuario

Numark

Numark iCDMIX 2 Manual de usuario

Numark

Numark C3 Manual de usuario

Numark

Numark IDJ LIVE II Manual de usuario

Numark

Numark NS7 Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario