Nowsonic STAGETRIP 10 Manual de usuario

Active on-stage monitor

and FOH full-range speaker

User manual

Bedienungsanleitung

Mode d‘emploi

Manual del usuario

Podręcznik użytkownika

STAGETRIP 10/12

User manual 4

Bedienungsanleitung 12

Mode d‘emploi 20

Instrucciones de uso 28

Instrukcja obsługi 36

Nowsonic Stagetrip 10 / Stagetrip 12

User manual

GB www.nowsonic.com

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any of the ventilation openings! Install in

accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliﬁers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong is provided

for your safety. If the provided plug does not ﬁt into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched,

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11) Only use attachments/accessories speciﬁed by the manufacturer.

12) Use only with a cart, stand, tripod, bracket, or table speciﬁed by

the manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to

avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualiﬁed service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally,

or has been dropped.

Nowsonic Stagetrip 10 / Stagetrip 12

User manual

www.nowsonic.com

The lightning ﬂash with an arrowhead symbol within an equilateral

triangle is intended to alert the user to the presence of uninsulated

“dangerous voltage”within the product’s enclosure that may be of

suﬃcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating and

maintenance(servicing) instructions in the literature accompanying

the product.

WARNING:

 To reduce the risk of ﬁre or electric shock, do not expose this

apparatus to rain or moisture.

 Do not expose this equipment to dripping or splashing and

ensure that no objects ﬁlled with liquids, such as vases, are placed

on the equipment.

 This apparatus must be earthed.

 Use a three-wire grounding type line cord like the one supplied

with the product.

 Be advised that diﬀerent operating voltages require the use of

diﬀerent types of line cord and attachment plugs.

 Always observe the local safety regulations.

 This equipment should be installed near the socket outlet and

disconnection of the device should be easily accessible.

 To completely disconnect this equipment from the AC Mains,

disconnect the power supply cord plug from the AC receptacle.

 Please follow all instructions of the manufacturer for installation.

 Do not install in a conﬁned space.

 Do not open the unit – risk of electric shock.

CAUTION!

Please note: Changes or modiﬁcations to the device not expressly

approved in this manual could void your authority to operate the

instrument.

Servicing

 There are no user-serviceable parts inside.

 All service must be performed by qualiﬁed personnel.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE THE COVER. NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

Nowsonic Stagetrip 10 / Stagetrip 12

User manual

GB www.nowsonic.com

Introduction

Thank you very much for purchasing the Nowsonic Stagetrip 10/12

active speaker. The Nowsonic Stagetrip 10/12 is an active mono

speaker oﬀering considerably better directivity thanks to a coaxial ar-

rangement of the woofer and the tweeter. The on-axis audio output

improves source location and also considerably minimizes unwanted

eﬀects caused by phase cancellation or addition. The Stagetrip 10

features a 10” woofer plus a 1” titanium dome tweeter; the internal

bi-amping power ampliﬁer provides 300 watts for the woofer and

100 watts for the tweeter. The Stagetrip 12 includes a 12” woofer and a

1.35” titanium dome tweeter driven at 100 and 450 watts, respectively.

Thanks to its enclosure design and the speaker-stand mount adapt-

er, you can use the Stagetrip 10/12 as a ﬂoor wedge for monitoring

purposes or as a full-range speaker for front-of-house (FOH) applica-

tions. When mounting the speaker onto a stand, the power ampliﬁer

will be positioned at the bottom, thus improving protection against

humidity and dirt. On the input side, the Stagetrip 10/12 accepts line

signals (from a mixing console, a CD player, etc.). In addition, you can

connect a dynamic microphone after adjusting the input sensitivity

using a dedicated switch. A high-pass ﬁlter can be engaged to increase

intelligibility.

The Stagetrip 10/12 also has output sockets for audio and power pass-

through.

Features

 Active two-way speaker system with coaxial speaker arrangement

 1 × 10”/ 1 × 12” woofer plus 1 × 1”/ 1 × 1.35” titanium dome

tweeter

 60° × 60° sound-ﬁeld coverage

 High power and high sound pressure due to a built-in bi-amping

power ampliﬁer (300/450 watts and 100 watts, respectively)

 Combo socket providing for directly connecting dynamic

microphones or line sources

 Power supply through mechanically secured PowerCon port,

power passthrough to following devices

 Separate high-pass ﬁlter (120 Hz)

 Rugged enclosure from multilayer plywood

Applications

 High-performance on-stage ﬂoor wedge

 Full-range FOH speakers for small-scale sound-reinforcement

applications

 Easy-to-use rehearsal amp for vocalists

 Personal full-range monitor speaker for instrument preamps

of guitar or bass players, etc.

Nowsonic Stagetrip 10 / Stagetrip 12

User manual

www.nowsonic.com

Connectors and controls

You can access the following connectors and controls on the right-

hand side panel of the Stagetrip 10/12:

1. POWER switch and fuse

Use this switch to turn the internal power ampliﬁer of the Stagetrip

10/12 on or oﬀ: when power is properly supplied through the POWER

IN socket (3) to the speaker, the POWER indicator (4) will light.

The fuse of the internal ampliﬁer is located adjacent to the POWER

switch: if the POWER indicator does not light after turning on the

switch and the coaxial speaker does not produce any audible noise, be

sure to check the internal fuse ﬁrst.

NOTE: DISCONNECT THE POWERCON CABLE BEFORE OPE

NING THE FUSE HOLDER. Use a suitable tool such as a screwdri-

ver for opening the fuse holder, then remove the holder from the

enclosure. ALWAYS replace with a fuse of the same type (T2.0AL

250 V); failing to do so might result in damage to the power am-

pliﬁer.

2. POWER OUT socket

The PowerCon-type POWER OUT socket of the Stagetrip 10/12 allows

for passing the input power through to following devices.

NOTE: Note that the POWER OUT port supplies a maximum

current of 4 A. Therefore, if the following consumer requires more

power, connect it directly to the mains.

Nowsonic Stagetrip 10 / Stagetrip 12

User manual

GB www.nowsonic.com

3. POWER IN socket

Connect the supplied PowerCon cord to the POWER IN socket. To do

so, insert the PowerCon connector into the socket, then turn it clock-

wise until it locks into place. This will ﬁrmly attach the connector to the

device, so it cannot be removed accidentally. To unplug the connector,

pull the spring-mounted catch back, then turn the connector coun-

terclockwise.

If the power cord gets lost, please contact the dealer where you

purchased your Stagetrip 10/12 unit for replacement.

4. SIG/CLIP and POWER indicators

When the Stagetrip 10/12 has been connected to the mains using the

supplied power cord and has been switched on, the green POWER

indicator will light constantly. If the indicator remains dark, be sure to

check the internal fuse (see step 1).

The SIG/CLIP indicator will light up when a signal is present at the

INPUT socket (–20 dB). If the signal level exceeds the sensitivity of the

Stagetrip 10/12 input stage, the indicator will change to red; in this

case, lower the source level until the indicator does not light up in red

anymore.

5. LEVEL control

You can adjust the level of the internal power ampliﬁer of the Stagetrip

10/12 using the LEVEL control.

6. LINK socket

The LINK socket allows for passing the signal present at the INPUT

socket (7) through to following units (for example, other Stagetrip

monitor speakers). The socket outputs a line signal.

7. INPUT socket

The INPUT combo socket allows for connecting an external source to

the internal power ampliﬁer of the Stagetrip 10/12. The Stagetrip 10/12

accepts microphone and line signals. Use the MIC/LINE switch (9) for

adjusting the input sensitivity as required.

The line-in part of the socket is a TRS (balanced) input.

NOTE: As the INPUT socket of the Stagetrip 10/12 outputs no

phantom power, it is not suitable for connecting a condenser

microphone directly; using that kind of microphone requires an

external power supply.

8. FLAT/LOW CUT button

Pushing this button enables the internal high-pass ﬁlter used for

reducing subsonic noise (below 120 Hz). When the high-pass ﬁlter

is on, it will reduce low-frequency noise (for example, when using

the Stagetrip 10/12 as a ﬂoor wedge) or pops (when connecting a

microphone). Pressing the button again disables the ﬁlter.

Nowsonic Stagetrip 10 / Stagetrip 12

User manual

www.nowsonic.com

9. MIC/LINE button

Using this button, you can adjust the input sensitivity of the Stagetrip

10/12 to the source connected to the INPUT socket. When connecting

a microphone, turn the switch on to increase the sensitivity; when the

switch is oﬀ, the INPUT socket accepts line sources.

NOTE: Always remember to set the input sensitivity appropriately.

Feeding a line signal while the MIC/LINE switch is on can result

in audible clipping as you might overdrive the input stage; on the

other hand, you may not achieve a suﬃcient volume level when

connecting a microphone with the MIC/LINE switch disabled.

Therefore, whenever output-level issues occur, be sure to check

the status of the MIC/LINE switch ﬁrst.

Using the Stagetrip 10/12 as an FOH Speaker

You can use the Stagetrip 10/12 not only as a monitor speaker but also

as a full-range speaker for small-scale FOH applications. For that pur-

pose, the enclosure of the Stagetrip 10/12 features a mount adapter for

standard-size speaker stands (extension-tube diameter: 35-mm / 13

/8”)

on the right-hand side next to the connector and operation panel. The

beneﬁt of this design is that all connections, controls, and the inter-

nal power ampliﬁer are located at the enclosure bottom, thus oﬀering

better protection against humidity, dirt, and/or direct sunlight.

When using the Stagetrip 10/12 as an FOH speaker, lift it carefully and

insert the extension tube of the speaker stand into the mount adapter.

When doing so, make sure that the tube is fully inserted into the mount

adapter to ensure maximum stability.

WARNING: Always make sure that the speaker stand‘s center of

gravity is low enough so that the Stagetrip 10/12 may not acci-

dentally fall over. Tighten all threads of the stand properly and

protect the setup of the Stagetrip 10/12 and the speaker stand

from falling over as appropriate.

IN NO EVENT SHALL NOWSONIC BE LIABLE FOR DAMAGE

OF ANY KIND THAT RESULTS FROM A STAGETRIP SPEAKER

MOUNTED ONTO A SPEAKER STAND FALLING OVER.

Nowsonic Stagetrip 10 / Stagetrip 12

User manual

GB www.nowsonic.com

Specications Scope of supply

 Stagetrip 10/12: 1 pc

 PowerCon cord: 1 pc

 User manual: 1 pc

Disclaimer

Nowsonic has taken all possible steps to ensure that the information

given here is both correct and complete.

In no event can Nowsonic accept any liability or responsibility for any

loss or damage to the owner of the equipment, any third party, or any

equipment which may result from use of this manual or the equipment

which it describes.

Servicing

If you have any question or encounter technical issues, please ﬁrst

contact your local dealer from whom you have purchased the device.

In case servicing is required, please contact your local dealer. Other-

wise you may contact us directly. Please ﬁnd our contact data on our

website under www.nowsonic.com.

Model Stagetrip 10 Stagetrip 12

Type Self-powered coaxial 2 way speaker for full-range

applications

Speakers 1 × 10“ woofer and 1 × 1“

titanium dome tweeter

1 × 12“ woofer and 1 × 1.35“

titanium dome tweeter

Crossover frequency 2.6 kHz 2.5 kHz

Coverage pattern 60° × 60° (coaxial horn)

Output power max. 300W + 100W

(bi-amping)

max. 450 W + 100W

(bi-amping)

Setting options Level, Flat/Low Cut (120Hz) button, Mic/Line Input

button

Inputs Mic/Line input via XLR/TRS combo socket

Mic-input sensitivity 6 mV

Line-input sensitivity 450 mV

Power connection PowerCon In (blue), PowerCon Out (grey), max. 4 amps

Supply voltage 220–240 V, 50 Hz

Power consumption 450 watts 600 watts

Fuse T2.0AL 250 V

Frequency range 65 Hz–20 kHz 55 Hz–20 kHz

SPL max. 121dB max. 123dB

Enclosure Multiplex plywood, coated

Dimensions 408 × 361 × 460 mm 482 × 406 × 530 mm

Color structure coating, black

Weight 12.8 kg 16.0 kg

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Oradores de Nowsonic

Nowsonic

Nowsonic Roadtrip 508 Manual de usuario

Nowsonic

Nowsonic ROADTRIP 52 Manual de usuario

Manuales populares de Oradores de otras marcas

argon audio

argon audio IE20 Manual de usuario

Denon

Denon SC-N7 Manual de usuario

Gemline

Gemline Ace 3952 Manual de usuario

Focal

Focal ON WALL 300 Manual de instrucciones

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manual de usuario

SoundLogic

SoundLogic BCCS-6/6395 Manual de usuario

Peavey

Peavey DTH 218 Manual de usuario

Avantree

Avantree Pluto Air Manual de usuario

Morel

Morel Integra Series INTEGRA OVATION 4 Manual de usuario

Oppo

Oppo SONICA Manual de usuario

Bose

Bose SoundLink Wireless Music System Manual de usuario

Rocksteady

Rocksteady Stadium Manual de usuario

Bowers & Wilkins

Bowers & Wilkins 4 Manual de usuario

Sonance

Sonance SONOS OUTDOOR Series Manual de usuario

Electro-Voice

Electro-Voice EVID FM4.2 Manual de usuario

Pioneer

Pioneer XW-HTD630 Manual de usuario

Onn

Onn BWA16AA002 Manual de usuario

HP GL313AA - USB Speakers PC Multimedia Manual de usuario