Novus NVM-517LCD Manual de usuario
NVM-517LCD
NVM-519LCD
U s e r ’s m a n u a l
NVM-517LCD, NVM-519LCD - User’s manual ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
2
EMC (2004/108/EC) and LVD (2006/95/EC ) Directives
CE Marking
Our products are manufactured to comply with the requirements of the following directives and national
regulations implementing the directives:
•
Electromagnetic compatibility EMC 2004 108 EC.
•
Low voltage LVD 2006 95 EC with further amendment. The Directive applies to electrical
equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as
75VDC and 1500VDC.
WEEE Directive 2002/96/EC
nformation on Disposal for Users of Waste Electrical and Electronic Equipment
This appliance is marked according to the European 1000VAC Directive on Waste Electrical and
Electronic Equipment (2002 96 EC) and further amendments. By ensuring this product is disposed of
correctly, you will help to prevent potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this product.
The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be
treated as household waste. It shall be handed over to the applicable collection point for used up electrical and
electronic equipment for recycling purpose. For more information about recycling of this product, please contact
your local authorities, your household waste disposal service or the shop where you purchased the product.
RoHS Directive 2002/95/EC
Out of concern for human health protection and friendly environment, we assure that our products
falling under RoHS Directive regulations, regarding the restriction of the use of hazardous substances
in electrical and electronic equipment, have been designed and manufactured in compliance with the
above mentioned regulations. Simultaneously, we claim that our products have been tested and do not
contain hazardous substances whose exceeding limits could have negative impact on human health or natural
environment.
nformation
The device, as a part of professional CCTV system used for surveillance and control, is not designed for self
installation in households by individuals without technical knowledge.
The manufacturer is not responsible for defects and damages that result from improper or inconsistent with
user’s manual installation of the device in the system.
FORMAT O
NVM-517LCD, NVM-519LCD - User’s manual ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
3
WAR G!
THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A
PROPER DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE
YOURSELF WITH THE MANUAL PRIOR TO INSTALLATION AND FURTHER
DEVICE OPERATION.
WAR G!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO
USER-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE
PERSONNEL MAY OPEN THE UNIT
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
WAR G!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN
PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE
PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE
PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF
EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN
ACTION.
MPORTAT SAFEGUARDS AD WAR GS
1. Prior to undertaking any action please consult the following manual and read all the safety and
operating instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual
is necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a
direct influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the
user’s manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer
is forbidden;
7. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers
etc.) is not recommended since it may lead to heat build-up and damaging the device itself
as a consequence;
8. Mounting the monitor on unstable surface or using not recommended mounts is forbidden.
Improperly mounted monitor may cause a fatal accident or may be seriously damaged itself. The
monitor must be mounted by qualified personnel with proper authorization, in accordance with this
user’s manual;
MPORTAT SAFEGUARDS AD WAR GS
NVM-517LCD, NVM-519LCD - User’s manual ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
4
MPORTAT SAFEGUARDS AD WAR GS
9. Device should be supplied only from a power sources whose parameters are in accordance with
those specified by the producer in the device’s technical datasheet. Therefore, it is forbidden to
supply the monitor from a power sources with unknown parameters, unstable or not meeting
producer’s requirements;
10. Signal and power cables should be placed in a way excluding the possibility of damaging them by
accident. Special attention must be paid to cables getting from the monitor and connecting the
power supply;
11. Electric installation supplying the device should be designed to meet the specifications given
by the producer in such a way that overloading is impossible;
12. User cannot repair or upgrade the equipment himself. All maintenance actions and repairs should
be conducted only by qualified service personnel;
13. Unplug the monitor from the power source immediately and contact the proper maintenance
department when the following occurs:
♦ Damages to the power cord or to the plug itself;
♦ Liquids getting inside the device or exposure to strong mechanical shock;
♦ Device behaves in a way not described in the manual and all adjustments approved by the
manufacturer and possible to apply by user himself, seem not to have any effect;
♦ Monitor is damaged;
♦ Atypical behaviour of the monitor components may be seen (heard).
14. In necessity of repairs attention to using only original replacement parts (with their parameters
in accordance with those specified by the producer) should be paid. Non-licensed service and
non-genuine replacement parts may cause fire or electrocution;
15. After maintenance activities tests should be run to ensure proper operation of all the functional
components of the device.
Attention!
Technical changes reserved without prior notice and printing errors possible.
NVM-517LCD, NVM-519LCD - User’s manual ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
5
1. PACKAGE COTETS
•
Monitor 17” 19” TFT LCD;
•
Base of the monitor;
•
230VAC 12VDC power supply, with cable;
•
VGA cable;
•
User’s manual.
2. MA CHARACTER ST CS
• High resolution colour TFT LCD monitor
• Panel type: 17”, 19” (depending on the model)
• LCD panel protected by glass shield
• Digital 3D filters for improved quality
• DNR (Digital Noise Reduction)
• CTI (Colour Transient Improvement)
• Multi – lingual On-Screen Display (OSD)
• Video input: 2xBNC (loop-through), HDMI, S-Video, VGA
• Easy Installation feature allowing easy access to connectors
• Wall mounting possibility
• LCD panel Anti-sticking function
• Operation system: PAL NTSC (Auto Scan)
• Audio input: stereo Jack (loop-through)
• Internal speakers
Power supply: 12VDC(100~240 VAC 12 VDC PSU in-set included)
FOREWORD FORMAT O
NVM-517LCD, NVM-519LCD - User’s manual ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
6
3. SPEC F CAT O
FEATURES AD SPEC F CAT O
Model
NVM-517LCD NVM-519LCD
Panel type
17” Colour TFT LCD panel
19” Colour TFT LCD panel
Panel resolution
Screen size (diagonal)
431,0 (mm) 482,6 (mm)
Horizontal resolution
700 TVL
Viewable size
337,9 x 270,3 (mm) 376,3 x 301,1 (mm)
Dot pitch
0,264 x 0,264 (mm) 0,294 x 0,294 (mm)
Viewing angle (L/R/T/B)
80
˚
80
˚
80
˚
80
˚
85
˚
85
˚
80
˚
80
˚
Contrast ratio
1000:1
Brightness
250 cd m
2
Display colour
16,7 mln
Response time
5 ms
Video input
2 x CVBS: BNC connector (loop-through)
1 x VGA
1 x HDMI
1 x S-Video
Audio
Audio input
1 x stereo mini-Jack (loop-through); 1x HDMI
Speaker
2 x 1 W
Setup
Multi-lingual On Screen Display (OSD)
Operation system
PAL NTSC (Auto scan)
Power supply
12 VDC (100~240 VAC 12 VDC PSU in-set included)
Power consumption
42W
Case
Plastic (Black), LCD protecting glass shield
Operating temperature
0°C ~ 40°C
Dimensions (mm)
371 (W) x 376 (H) x 197 (D) 419 (W) x 423 (H) x 197 (D)
Weight
4,5 kg 5,2 kg
Mounting standard
VESA 100 x 100 mm
1280x1024
NVM-517LCD, NVM-519LCD - User’s manual ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
7
3.1 Detailed dimensions
All dimensions are given in millimeters:
Model A B C D E
NVM-517LCD 371 325 376 54 197
NVM-519LCD 419 358 423 54 197
FEATURES AD SPEC F CAT O
NVM-517LCD, NVM-519LCD - User’s manual ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
8
4. POS T O AD FUCT OS OF MO TOR COMPOETS
4.1 Front panel
i - button - opens video input selection menu that allows to select one of following
inputs: CVBS1, CVBS2, S-VIDEO, VGA, HDMI. In order to select desired
input please press i - button several times. Please press M button to confirm
your selection.
„
-
”
- button - allows to display volume adjustment menu
- during navigation through OSD menu selects previous category or decreases
parameter value
„
+
”
- button - freezes currently displayed picture frame
- during navigation through OSD menu selects next category or increases
parameter value
M - button - pressing during navigation through OSD menu applies selection
- in order to lock unlock front panel buttons please keep this button pressed
for at least 10 seconds
LED - GREEN - power on,
- ORANGE - standby mode,
- flashing ORANGE - sleep mode,
- flashing GREEN - freeze mode, „+” was pressed
- button - turns monitor on off
POS T O AD FUCT OS OF MO TOR COMPOETS
NVM-517LCD, NVM-519LCD - User’s manual ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
9
4.2 Connectors
(A) AUDIO IN - audio input, stereo mini-Jack
(B) AUDIO OUT - audio output (loop-through input), stereo-mini-Jack
(C) CVBS1 Out - video out 1 - loop-through output of CVBS1 IN input
(D) CVBS1 IN - video in 1, CVBS, BNC type
(E) CVBS2 Out - video out 2 - loop-through output of CVBS2 IN input
(F) CVBS2 IN - video in 2, CVBS, BNC type
(G) S-VIDEO - S-video input (Y C), 4-pin mini-DIN
(H) HDMI - HDMI input
(I) VGA - VGA input
(J) DC 12V - 12VDC power input
POS T O AD FUCT OS OF MO TOR COMPOETS
NVM-517LCD, NVM-519LCD - User’s manual ver. 1.0
All rights reserved © AAT Holding sp. z o.o.
10
4.3 Easy Installation feature
Thanks to Easy Installation feature user can tilt screen back to its horizontal position. That gives full
access to all connectors of the monitor.
Monitor features holes (located at the bottom of its base plate) for screws (not being part of the set),
therefore enabling the option of easy wall mounting, without any additional accessories.
POS T O AD FUCT OS OF MO TOR COMPOETS
Easy access to rear connectors
Wall mounting option
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Monitor de Novus
