Norton Clipper CS 352 B Manual de usuario

CS 352 B

OPERATING INSTRUCTIONS

Translation of the original instructions

VERS.2023.03.15 CS 352 B_MAN_EN

The undersigned manufacturer:

SAINT - GOBAIN ABRASIVES S.A.

190, BD. J. F. KENNEDY

L-4930 BASCHARAGE

Declares that this product:

« Floor saw »: CS 352 B Code : 70184632546

is in conformity with the following Standards:

•"MACHINES" 2006/42/CE

•"ELECTROMAGNETIC COMPATIBILITY" 2014/30/UE

•"NOISE" 2000/14/CE

And the European standard:

•EN 13862 –Floor cutting-off machines –Safety

Valid for machines as of serial number: 221000014

Storage site for the technical documents:

Saint-Gobain Abrasives 190, Bd. J. F. Kennedy 4930 BASCHARAGE, LUXEMBOURG

This declaration of conformity loses its validity when the product is converted or modified without

agreement.

Bascharage, 15/03/2023.

François Chianese, executive officer and responsible for the technical file.

Bascharage, Luxembourg.

Declaration of conformity

VERS.2023.03.15 CS 352 B_MAN_EN

The undersigned manufacturer:

SAINT - GOBAIN ABRASIVES S.A.

190, BD J.F. KENNEDY

L- 4930 BASCHARAGE

Declares that this product:

« Floor saw »: CS 352 B Code : 70184632546

is in conformity with the following standard:

•Supply of Machinery (Safety) Regulations 2008

•Electromagnetic Compatibility Regulations 2016

•Noise Emission in the Environment by Equipment

for use Outdoors Regulations 2001

and European standard:

•EN 13862 –Floor cutting-off machines –Safety

Valid for machines with a serial number greater than: 221000014

Authorised Representative:

SAINT-GOBAIN ABRASIVES

Unicorn House • Unit 1, Amison Close

Redhill Business Park • Stafford • England • ST16 1WB

This declaration of conformity loses its validity when the product is converted or modified without

agreement.

Bascharage, 18/10/2022.

François Chianese, executive officer and responsible for the technical file.

Bascharage, Luxembourg.

Declaration of conformity

VERS.2023.03.15 CS 352 B_MAN_EN

CS 352 B

OPERATING INSTRUCTIONS

1BASIC SAFETY INSTRUCTIONS 6

1.1 Symbols 6

1.2 Machine plate 7

1.3 Safety instructions for particular operating phases 8

2GENERAL DESCRIPTION OF THE CS 352 B 9

2.1 Short description 9

2.2 Layout 9

2.3 Technical data 12

2.4 Statement regarding the vibration emission 13

2.5 Statement regarding noise emission 14

3ASSEMBLY AND COMMISSIONING 15

3.1 Assembly 15

3.2 Tool assembly 15

3.3 Quick reference guide for operation 16

3.4 Battery fixation and starting the machine 17

3.5 Charging the battery 18

3.6 Water cooling system 18

4OPERATING THE CS 352 B 19

4.1 Site of work 19

4.2 Cutting method 19

5TRANSPORT AND STORING 20

5.1 Securing for transport 20

5.2 Transport procedure 20

5.3 Long period of inactivity 20

6MAINTENANCE AND SERVICE 21

6.1 Maintenance of the machine 21

6.2 Maintenance of the engine 22

7FAULTS: CAUSES AND CURES 23

7.1 Fault-finding procedures 23

7.2 Trouble-shooting guide 23

7.3 Customer service 24

7.4 Spare parts 25

VERS.2023.03.15 CS 352 B_MAN_EN

1 BASIC SAFETY INSTRUCTIONS

The CS 352 B is exclusively designed for the cutting of floors made of asphalt, green and cured

concrete (reinforced or not) as well as of industrial cement.

Uses other than the manufacturer's instructions shall be considered as contravening the

regulations. The manufacturer shall not be held responsible for any resulting damage. Any risk

shall be borne entirely by the user. Observing the operating instructions and compliance with

inspection and servicing requirements shall also be considered as included under use in

accordance with the regulations.

1.1 Symbols

Important warnings and pieces of advice are indicated on the machine using symbols. The

following symbols are used on the machine:

Read operator’s instructions

Ear protection must be worn

Hand protection must be worn

Eye protection shall be worn

Cutting depth indicator

Danger: risk of cut

VERS.2023.03.15 CS 352 B_MAN_EN

Rotation of the wheel in the indicated

direction lowers the blade

Rotation of the wheel in the indicated

direction raises the blade

Never move the machine with the blade

running idle.

Rotation direction of the blade

Emergency Stop

1.2 Machine plate

Important data can be found on the following plate located on the machine:

Ø Bore

Machine type

Serial number

Power

Safety standard

Machine Model

Machine Code

Blade speed

Weight

Year of

production

ØMaximum

blade

VERS.2023.03.15 CS 352 B_MAN_EN

1.3 Safety instructions for particular operating phases

Before commencing work

•Before commencing work, make yourself familiar with the working environment at the place

of use. The working environment includes: obstacles in the area of work and manoeuvre, the

firmness of the floor, necessary protection at the site relating to public thoroughfares and the

availability of help in the event of accidents.

•Check for correct mounting of the blade regularly.

•Immediately remove damaged or badly worn blades, as they endanger the operator whilst

rotating.

•Only fit NORTON diamond blades to the machine! The use of other tools can damage the

machine!

•Attention is drawnto the use of BS2092safety goggles in conformity with specified Processes

No.8 of the Protection of Eyes Regulation 1974, Regulation 2(2) Part 1.

•For security reasons, never leave the machine unattended, untied or unlocked.

While the engine is running

•Do not move the machine whilst the blade is running idle.

•Always cut with the blade guard in position.

•Apply cooling water continuously whilst cutting and in good time!

Battery powered machine

•Always turn off the machine and separate it from the battery before any work on the machine

is done.

•Avoid contact of the electric connections with water projection or humidity.

•In case of emergency, you can stop the machine by pushing on the emergency stop.

•In the event of the machine breaking down or stopping for no apparent reason, switch off the

machine and separate it from the battery. Only a qualified electrician is allowed to investigate

the trouble and remedy the fault.

VERS.2023.03.15 CS 352 B_MAN_EN

2 GENERAL DESCRIPTION OF THE CS 352 B

Any modification, which could lead to a change in the original characteristics of the machine, may

be done only by Saint-Gobain Abrasives S.A. who shall confirm that the machine is still in

conformity with the safety regulations. Saint-Gobain Abrasives S.A. keeps the right of making

technical or design modification without prior notification.

2.1 Short description

The Floor Saw CS 352 B you have chosen,is used for small repair works in concrete and asphalt,

for cutting induction loops and installing cables as well as for cutting expansion joints. It can be

used for either wet or dry cutting operations.

Being of small construction, it can be transported in a car or van, the handle can be removed,

reversed or retracted. The water container is also removable.

All component parts on the CS 352 Bare assembled to a high quality standard, ensuring long

life, reliability and a minimum of maintenance.

Special types of blades are available for asphalt, green concrete, cured concrete (reinforced or

not) as well as for industrial cement flooring.

2.2 Layout

VERS.2023.03.15 CS 352 B_MAN_EN

Made of jig welded open profile steel, the CS 352 is stable but at the same time, easily

transportable.

The one-piece blade guard (1) fully protects the operator and his working environment. It is firmly

fixed to the main frame but can be opened by rotation to change blades.

A manually operated hand wheel mechanism (2) enables graduated depth setting. Turning the

hand wheel clock- or anti-clockwise will raise or lower the cutting blade.

The handle (3) is detachable or can be reversed for easy transportation. The height is adjustable.

The motor frame (4), supporting the blade shaft, the motor, the blade guard and the belt guard, is

articulated on the rear axle.

Tabla de contenidos

Otros manuales de Sierra de Norton

Norton

Norton clipper CS1-500 P13 Manual de usuario

Norton

Norton BBL547 Manual de usuario

Norton

Norton C1316 Manual de usuario

Norton

Norton clipper CP512-300 Manual de usuario

Norton

Norton clipper CM 350 B Manual de usuario

Norton

Norton Clipper C13PE Manual de usuario

Norton

Norton clipper CGW EVO D400 Manual de usuario

Norton

Norton clipper CM 450 Junior Manual de usuario

Norton

Norton JCW 600 Manual de usuario

Norton

Norton CM 351 Manual de usuario

Norton

Norton C3120 Manual de usuario

Norton

Norton clipper TT 251 Manual de usuario

Norton

Norton CS 451 P13 Guía

Norton

Norton Clipper C1418P Manual de usuario

Norton

Norton GC55 Manual de usuario

Norton

Norton Clipper CTC1020XL Manual de usuario

Norton

Norton C1320P Manual de usuario

Norton

Norton Clipper TR 202 Manual de usuario

Norton

Norton TT 200 EM Manual de usuario

Norton

Norton BBL547 Manual de usuario

Norton

Norton CST 65 Modulo Manual de usuario

Norton

Norton BBL547 Manual de usuario

Norton

Norton clipper TR 231 GL Manual de usuario

Norton

Norton BBC157 Manual de usuario

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario

Norton clipper CS 352 B Manual de usuario

Manuales populares de Sierra de otras marcas