Norton clipper CDR 133 Guía
Kit CDR 133 + CDM 163
OPERATING INSTRUCTIONS AND SPARE PARTS LIST
Translation of the original instructions
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN
2
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN
3
The undersigned manufacturer:
SAINT - GOBAIN ABRASIVES S.A.
190, BD. J. F. KENNEDY
L-4930 BASCHARAGE
Declares that this product:
« Drill Rigs »: KIT CDR 133 + CDM 163 Code : 70184694704
is in conformity with the following Directives :
"MACHINES" 2006/42/CE
"LOW VOLTAGE" 2006/95/CE
"ELECTROMAGNETIC COMPATIBILITY " 2004/108/CE
"NOISE" 2000/14/CE
And the European standard:
EN 12348 –Core drilling machines on stand –Safety
Valid for machines as of serial number:
150500000
Storage site for the technical documents:
Saint-Gobain Abrasives 190, Bd. J. F. Kennedy 4930 BASCHARAGE, LUXEMBOURG
This declaration of conformity loses its validity when the product is converted or modified without
agreement.
Bascharage, Luxembourg, 19/05/2015.
Olivier Plenert, executive officer.
Declaration of conformity
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN
4
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN
5
Kit CDR 133 + CDM 163
OPERATING INSTRUCTIONS
1BASIC SAFETY INSTRUCTIONS 6
1.1 Symbols 6
1.2 Machine plate 7
1.3 Safety instructions for particular operating phases 8
2MACHINE DESCRIPTION 9
2.1 Short description 9
2.2 Purpose of use 9
2.3 Layout 9
2.4 Technical Data 10
2.5 Statement regarding the vibration emission 11
2.6 Statement regarding noise emission 12
3ASSEMBLY AND COMMISSIONING 13
3.1 Assembling the motor on the rig 13
3.2 Tool assembly 13
3.3 Electrical connections 13
3.4 Changing motor speed 14
3.5 Water cooling 14
4TRANSPORT AND STORING 15
4.1 Securing for transport 15
4.2 Transport procedure 15
4.3 Long period of inactivity 15
5OPERATING THE MACHINE 16
5.1 Site of work 16
5.2 Drilling method 16
6MAINTENANCE AND SERVICING 19
7FAULTS: CAUSES AND CURES 20
7.1 Fault-finding procedures 20
7.2 Trouble-shooting guide 20
7.3 Customer service 21
8APPENDIX 23
Ideal rotation speed of the core bit in relation to the hole diameter 23
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN
6
1 BASIC SAFETY INSTRUCTIONS
The core drill rig CDR 133 is exclusively designed for the drilling of construction products mainly
within a construction site.
Uses other than the manufacturer's instructions shall be considered as contravening the regulations.
The manufacturer shall not be held responsible for any resulting damage. Any risk shall be borne
entirely by the user. Observing the operating instructions and compliance with inspection and
servicing requirements shall also be considered as included under use in accordance with the
regulations.
1.1 Symbols
Important warnings and pieces of advice are indicated on the machine using symbols. The following
symbols are used on the machine:
Read operator’s instructions
Ear protection must be worn
Hand protection must be worn
Eye protection shall be worn
Airway protection must be worn
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN
7
1.2 Machine plate
Important data can be found on the following plate located on the machine:
Machine Model
Machine Code
Weight
Year of production
Machine type
Serial number
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN
8
1.3 Safety instructions for particular operating phases
Before commencing work
Before commencing work, make yourself familiar with the working environment at the place of
use. The working environment includes: obstacles in the area of work and manoeuvre, the
firmness of the floor, necessary protection at the site relating to public thoroughfares and the
availability of help in the event of accidents.
Immediately remove damaged or badly worn core bits, as they endanger the operator whilst
rotating.
Only fit NORTON diamond core bits to the machine! The use of other tools can damage the
machine!
Read the core bits’ specifications carefully to choose the adequate tool to your application.
Make sure the handle of the machine is free from oil or grease.
Attention is drawn to the use of BS2092 safety goggles in conformity with specified Processes
No.8 of the Protection of Eyes Regulation 1974, Regulation 2(2) Part 1.
Make sure that no mounting tool is left on the machine before starting it.
Electrical powered machine
Make sure that the electrical supply of the machine is equipped with a grounded protective
connector. If you have doubts, let a qualified electrician check the electrical system.
Never pull the machine by the cable to transport it or to separate it from the electrical supply.
Avoid any contact between the cable and extension cable and heat sources, oil, and sharp
edges.
Always check the cable before commencing work. If it is damaged, let a qualified electrician
replace it.
Switch the machine off, and isolate it from the main electrical supply before attempting any
maintenance or repair on the machine
In the event of the machine breaking down or stopping for no apparent reason, switch off the
main electricity supply. Only a qualified electrician is allowed to investigate the trouble and
remedy the fault.
Always isolate the machine from the electrical supply when not in use.
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN
9
2 MACHINE DESCRIPTION
Any modification, which could lead to a change in the original characteristics of the machine, may
be done only by Saint-Gobain Abrasives who shall confirm that the machine is still in conformity with
the safety regulations.
2.1 Short description
The CDR 133 core drill rig is designed for durability and high performance for onsite wet and dry
drilling operations of a wide range of masonry and natural stone products.
As with all other NORTON products, the operator will immediately appreciate the attention given to
detail and quality of materials used in construction. The machine and its component parts are
assembled to high standards assuring long life and minimum maintenance.
2.2 Purpose of use
The machine is designed for drilling a large range of building materials. It is not designed for drilling
wood or metals, except steel reinforcing securely embedded in concrete.
2.3 Layout
There are two main parts on the core drilling rig CDR 133: the motor and the rig itself.
The rig is made of sectional aluminium, which reduces the weight of the machine allowing easy
transportation. The base ensures stability of the rig, and allows two ways of fixing the rig: using a
vacuum pump or fixing anchors. The rig is equipped with a collar, so that the motor can be fitted or
removed quickly from the rig
Three different types of electric motor are available on the CDR 133, offering excellent quality of
drilling and extended life duration. Every motor is equipped with a P.R.C.D. (Portable Residual
Current Device). This circuit breaker protects the motor from an electrical overload. The P.R.C.D. is
a circuit breaker and not a switch. Always stop the motor using its switch and not the P.R.C.D.
VERS.2015.05.19 Kit CDR 133 + CDM 163_MAN_EN
10
2.4 Technical Data
Rig
Max. drill bit diameter
130mm
Movement
540mm
Tilting
NO
Weight
8.9 kg
Dimensions(Length x width x height)
375x250x870mm
You can find the code number on the machine plate. If you bought a complete kit, your machine is
composed of a column with combined base, a motor. These are the characteristics of the motor:
Motor 70184647807
Motor
CDM 163
Power
1.8 kW
Motor protection
P.R.C.D. 10mA
Rotation speeds
525/1150/2400 min-1
Weight
8,1 kg
Range of core bit diameter
15-160mm
Connector
½’’ + 1¼’’
Kit Rig + Motor
Weight
17 kg
Dimensions (Length x width x height)
375x400x870mm
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Perforar de Norton
