HR30 Quick Reference Guide
The HR30 allows users to enjoy wireless control of their system from
any zone in the house. A few simple steps are required prior to using
your new HR30 remote control.
You will need the following items which are included in the HR30 kit:
A. Remote
B. Charging Station
C. USB to Micro-USB Cable
D. 5V 2.00A Power Supply
Required items not included in HR30 kit:
System Controller with compatible software.
Optional items purchased separately:
2900008 – Additional Battery
HR30CS – Additional Charging Station
Please note:
The HR30 requires a controller running with compatible software.
Accessing the Micro-USB Programming Port, and On/Off Switch
The HR30 is shipped with the power switch in the “off” position to conserve
battery life. Prior to setup the endcap must be removed and the power switch
must be changed to the “on” position. To access the power switch locate the
Endcap Release Button on the bottom of the remote.
While depressing the endcap release button pull the endcap away from the body
of the remote as illustrated. Move the On/Off power switch located on the
right side to the “on” position. (For extended periods of non-use it is
recommended to turn the remote off with this switch to conserve the battery life.)
Replace endcap and follow the charging instructions below.
Limited Warranty
Nortek Security & Control ( ‘NSC’ ) warrants the HR30 to be free from defects
in materials and workmanship for the period of two years (2 years) from the date
of purchase. If within the applicable warranty period above purchaser discovers
that such item was not as warranted above and promptly notifies ‘NSC’ in writing,
‘NSC’ shall repair or replace the item at the company’s option.
This warranty shall not apply (a) to equipment not manufactured by ‘NSC’,
(b) to equipment which shall have been installed by other than an ‘NSC’ authorized
installer, (c) to installed equipment which is not installed to ‘NSC’s’ specifications,
(d) to equipment which shall have been repaired or altered by others than ‘NSC’,
(e) to equipment which shall have been subjected to negligence, accident, or
damage by circumstances beyond ‘NSC’s’ control, including, but not limited to,
lightning, flood, electrical surge, tornado, earthquake, or other catastrophic events
beyond ‘NSC’s’ control, or to improper operation, maintenance or storage, or to
other than normal use of service. With respect to equipment sold by, but not
manufactured by ‘NSC’, the warranty obligations of ‘NSC’ shall in all respects
conform to the warranty actually extended to ‘NSC’ by its supplier. The foregoing
warranties do not cover reimbursement for labor, transportation, removal, installation
or other expenses which may be incurred in connection with repair or replacement.
Except as may be expressly provided and authorized in writing by ‘NSC’, ‘NSC’
shall not be subject to any other obligations or liabilities whatsoever withrespect
to equipment manufactured by ‘NSC’ or services rendered by ‘NSC’.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER
EXPRESSED AND IMPLIED WARRANTIES EXCEPT WARRANTIES OF TITLE,
INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
ATTENTION: TO OUR VALUED CUSTOMERS
To ensure that customers obtain quality pre-sale and after-sale support and
service, Nortek Security & Control products are sold exclusively through
authorized dealers. Nortek Security & Control products are not sold online.
The warranties on Nortek Security & Control products are NOT VALID if the products
have been purchased from an unauthorized dealer or an online E-tailer.
To determine if your Nortek Security & Control reseller is authorized,
please call Nortek Security & Control at (707) 283-5900.
Charging the Remote
Before configuring, the HR30 must be fully charged.
Charge the remote in the included charging cradle
for at least 2 hours prior to setup.
To charge, place the remote in the charging cradle and connect the included
power supply to the back of the charging cradle and wall outlet.
The remote display may light up briefly while beginning to charge.
It is recommended to place the remote in the charging cradle when not in use.
A B
C
D
© 2018 Nortek Security & Control, LLC. All rights reserved.
nortekcontrol.com
1
2
Micro-USB
Micro-USB
USB
5V 2.00A
Power Supply
(included)
