67
Alterations which serve the technological progress as well as errors excepted! ORIGINAL MANUAL NORSUPWWW.NORSUP.EU Alterations which serve the technological progress as well as errors excepted!
DE
EN
NL
FR
DK
SE
SALT CHLORINATOR TYPE OCEANCLEAR LSSALT CHLORINATOR TYPE OCEANCLEAR LS
3. ELECTRONICS UNIT
3.1. FIRST COMMISSIONING
When switching on the electronics unit for the first time, carry out the following programming.
3.2. KEYPAD
1. FUNCTIONS OF THE EQUIPMENT
2. INSTALLATION DIAGRAM
• The electrical connections at cell-level must not
point upwards, to avoid any deposits of water or
humidity on them.
• The pH corrector container must be installed a safe
distance away from any electrical device or any other
chemicals.
Model Chlorine
product-
ion via
electrolysis
pH
regulation
Regulation of
chlorine pro-
duction with
ORP probe
UNO
DUO
PRO
1: Salt / temperature /
low water sensor (optional)
2: Cell
3: Electronics unit
4: Filter with ballast
5: Peristaltic pump
6: Pool Ground (optional)
7, 8: Probe holder
9: Injection connector
10: ORP probe
11: pH probe
12, 13: Bracket
14, 15: Semi-flexible tubing
KEY :
UNO model : white
DUO model : white + grey
PRO model : white + grey + black
ELEMENTS NOT SUPPLIED :
16: Electrical power supply
17: pH corrector container
18: Copper cable
19: Filter
20: Ground rod
21: Heat pump
22: Filtration pump
3
2. INSTALLATION DIAGRAM
I
The electrical connections at cell-level must not point upwards, to avoid any deposits of water or humidity
on them.
The pH corrector container must be installed a safe distance away from any electrical device or any other
chemicals.
44
17
4
10
8
KEY :
UNO model : white.
DUO model : white + grey.
PRO model : white + grey + black.
1: Salt / temperature / low water sensor (optional)
2: Cell
3 : Electronics unit
4: Filter with ballast
5: Peristaltic pump
6 : Pool Ground (optional)
7,8: Probe holder
9: Injection connector
10 : ORP probe
11 : pH probe
12,13 : Bracket
14,15 : Semi-flexible tubing
9
1
7
6
19
H
16
18
2
3
13
20
22
5
12
11
14
15
ELEMENTS NOT SUPPLIED :
16 : Electrical power supply
17 : pH corrector container
18 : Copper cable
19 : Filter
20 : Ground rod
21 : Heat pump
22 : Filtration pump
21
SUCCESSIVE MENUS POSSIBLE SETTINGS NAVIGATION
• Français
• English
• Deutsch
• Español
• Italiano
• Nederlander
• Portugués
For each parameter, select a data
item with the buttons, then
confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
• In line
• Dashboard
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
COMMAND KEY
DEPENDING ON MODEL FUNCTION
• Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without
ORP check).
• Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
• Access the menus.
Boost mode starts for 24 hours.
• Water temperature display for a few seconds (only if the default display is set to
« In line display »).
• Direct access to the « » menu (press and hold).
• Salt level display for a few seconds (only if the default display is set to « In line display »).
• Direct access to the « » menu (press and hold).
g This command key is only present on the DUO and PRO models.
• Direct access to the « » menu (press and hold).
Selecting a value or data element.
• Cancellation of an entry
• Back to previous menu.
• Stopping Boost mode.
• Command confirmation.
• Entering a menu.
• Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
menus Possible settings Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués For each parameter, select a data item with the
buttons, then confirm with the OK button.
From 10 to 200 m3, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit (press and hold).
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds (only if the default display is set to « In
display »).
Direct access to the « » menu (press and hold).
SALT Salt level display for a few seconds (only if the default display is set to « In line display »).
Direct access to the « » menu (press and hold).
pH This command key is only present on the DUO and PRO models.
Direct access to the « » menu (press and hold).
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
