Nordson 3100V Series Guía de referencia

OWNER'S RECORD

MODEL AND SERIAL NUMBER INFORMATION:

The model and serial numbers are located at the hose/gun side of the unit.

A duplicate label is provided to you in the space below.

Refer to these numbers whenever you call upon your Nordson Customer Service

Representative regarding this product.

TANK AND HEATING PADS WARRANTY INFORMATION:

With respect to hot melt tanks and bulk melter heating pads with cast-in heating

elements, Nordson agrees to repair or, at it's option, replace any hot melt tank or bulk

melter heating pads determined by Nordson to have defective cast-in heaters, provided

the defect is reported in writing to Nordson within sixty(60) months of the date of

manufacture stamped on the hot melt tank or bulk meter heating pads.

THIS UNDERTAKING IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING IVERCHANTABILIry AND FITNESS FOR PARTICULAR PURPOSE.

UNIT INSPECTION INFORMATION:

Factory tested and approved: Date ?-/S-o //

Pump seriar number: 5,4Ct 6 /6q/a

NOTE:

Retain for your this document into owner's manual provided with unit.

l^lose +' 6Lt/J records. lnsert

(zz*vqs) /z+*v65

(z+++G s)

8Fr- TAolcaogSt +AD3tT

55 + AD3'1.

3400v -zEAV4D/R

230883A S401H00513

MilNHifN re

IIINE

Ultl t---t6]

ru Fso/oo ffi

IIIiEE

Erd t-rrc I

Nordson

@ gFr- TAotc oeq

Nordson Corporation

307130

SERIES 34OO Y

Hot Melt Material Applicator

with 6:1 SP30 Piston Pump and Vista'Controller

r 3400V-4GAVDUX

Customer Product Manual- Part 331 1g2F

NORDSON CORPORATION o AMHERST, OH|O o USA zl-"'

--'/'{

\',;

, -'ttr;:' /

f,-\.-".* \

,... tl :. (

Nordson.

(€

,\r

Nordson Corporation welcomes requesls for information, comments and inquiries about its products. General

information about Nordson can be found on lhe lnternet using the following address: http://wwwnordson.com.

Address all correspondence to:

Nordson Corporation

Attn: Customer Service

1'1475 Lakefield Drive

Duluth, GA 30097

Notice

This is a Nordson Corporation publication which is protected by copyright. Original copyright date 1999. No part of

this document may be photocopied, repioduced, or translated to another language without the prior written consent

of Nordson Corporation. The information contained in this publication is subject to change without notice.

Trademarks

AquaGuard, Blue Box, Control Coat, Equi=Bead, FoamMelt, FoamMix, Helix, Hot Shot, Hot Stitch, Meltex,

MicroSet, MultiScan, Nordson, the Nordson logo, OmniScan, Package of Values, Porous Coat, PosFStop, ProLink,

PRX, RBX, Shur-Lock, UniScan, UpTime, and Versa-Spray are registered trademarks of Nordson Corporation.

BetterBook, CF, Controlled Fiberization, Eclipse, Saturn, Seal Sentry, Swirl Coat, and Vista

are trademarks of Nordson Corporation.

Big Orange is a registered trademark of ZEP Manufacturing Company.

Loctite is a registered trademark of Loctite Corporation.

Never Seez is a registered trademark of Bostik CorpoAtion.

Parker Lubricant is a registered trademark of Parker Seal.

Teflon and Viton are registered trademarks of E.l. DuPont de Nemours & Co.

\ =t=-

41."

.:*l---.. *O 2000 Nordson Corporation

01 EN-01-[3V-3311 92]-1 lssued j

-6-

.a-l}

Nordson CorPoration

OPERATOR'S CARD

P/N 229 777c

Series 31OO Vlg4OOYl3500 Vl3700V

Hot tMelt tVlaterial APPlicator

with Piston Pump, standard Filter, standard control

IMPORTANT

Give this coPY

to the oPerator

Please Note

The operator's card contains only information

necessary for daily operation and maintenance'

Foiotreiintormation, reler to the product manual

A copy of this operator's card and an order form for

anotirer operator's card are included in the

introduction part of the operating manual'

AWARNING: Allow only qualified personnelto

perform the following tasks. Observe and

iollow the safety instructions in this document

and all other related documentation'

Always follow the instructions given in the

operator's card and operating manual'

Always follow instructions in the material supplier's

tvtateiiat Safety Data Sheet (MSDS) or material

information sheet.

Even at recommended operating temperatures'

hot melt material may release vapors' Exceeding

prescribed processing temperatures for long

periods of time can result in dangerous

decomposition by-products. Flemove vapors

by drawing them off with an exhaust system'

Safety SYmbols

The following symbols warn against dangers or

oossible sou-rces of danger. Become familiar with

inemt faiture to heed a warning symbol can lead to

personal injury and/or damage to the unit or other

equipment.

WARNING: Failure to observe can result in

equipment damage, personal injury, or death'

WARNING: Risk of electrical shock' Failure to

obserue can result in personal injury or death'

WARNING: Disconnect equipment from line

voltirge. Failure to observe can result in

personal injury or death.

WARNING: Hot! Risk of burns. Wear

heat-protective clothi n g, saf ety gog gles, and/or

heat-protective gloves depending on the

symbol or symbols shown. Failure to observe

can result in personal injury or death'

WARNING: Pressurized system or material

Release pressure. Failure to observe can

result in serious burns.

lssued 4/98 o 1 E N-O P C-[3V -229774-1

rvi

Ove EW of Stem Com o

ys nts

1Applicator

1. Pump

2. Tank

3. Air regulator

4. Filter and drain valve

5. Controls

Additional System Components

6. Hose

7. Air-operated gun

8. Solenoid valve

Clean the exterior sudaces of the applicator and

guns.

2. Check the o-rings and gaskets for leaks.

3. Flush the manifold filter as follows:

a. Reduce the pump air pressure to 0.

c. Open the drain valve over a container by

turning the valve counterclockwise.

b Place containers under all guns and trigger the

guns to relieve hydraulic pressure.

Type A Manifotd

TypeBorSManifold

d. lncrease the pump air pressure until a clean,

steady stream of hot melt materialflows from

the drain valve.

e. Close the drain valve.

f. Return the pump air pressure to the normal

operating setting.

Daily Maintenance

ol EN-oPc-[3V -229771_1 lssued 4/98

Dai ly Startu p/Sh utdown

8. When the READY light turns on, press the PUMP

key.

WARNING: When the tank lid is open, hot melt

vapors may be released. Vent the application

area or wear a respirator for protection from

vapors.

Automatic Startup/Shutdown

With the seven-day clock and auto-energize pump

features on, the following occur:

1. The heaters turn on automatically and the pump

starts when the tank reaches either the READY

condition or a temperature you have selected.

2. The heaters turn off automatically and the system

shuts itself down.

ManualStartup

1. Check the adhesive level. lf the level is below

50%, add adhesive to the tank. Fill to within

25 mm (1 inch) of the tank toP.

2. Close the lid immediately to prevent contamination

of the adhesive'

3. lf the POWER switch is off, turn it on.

4. Prepare each gun in your system for operation as

follows:

. Air-operated guns: turn on the operating air.

. Handguns: unlock the trigger.

o Electric guns: turn on the gun driver.

5. Press the HEATERS key. The HEATERS light will

turn on and the unit will begin to heat.

,*'*'@ffis

6. Turn on the pump air pressure and adjust it to the

setting that works best for your system.

7. Check the temperature setting for each heated

zone.

9. Check the adhesive level periodically. Refill the

tank before the level drops below 50%.

ManualShutdown

1. Press the PUN/P key. The PUMP light willturn off

and the pump will stoP.

?L'

PUMP +

2. Place containers beneath all guns and trigger the

guns to relieve hydraulic pressure.

3. Use one of the following methods to prevent

accidental gun triggering:

. Air-operated guns: reduce air pressure to 0

. Handguns: place the trigger safety in the

locked position.

. Electric guns: turn off the gun driver.

WARNING: Never hang a handgun by its

trigger. The gun can accidentally discharge

material, causing burns.

4. Press the HEATERS key. The HEATERS light will

turn off.

r,*rens6D o

\<=/

lssued 4/98 o 1 E N-O PC-[3V -22577n-1

Daily Operations

Todothis... Press this key . . . This happens .It means. .

Turn the power on POWER The POWER switch turns on Power to the unit is on

Turn the power off The POWER switch turns off. Power to the unit is off

Scan the temperatures

of each zone. The MONITOR/SCAN light

turns on and stays on. The system scans each

heated zone and displays

each zone's temperature.

The system displays the

temperature of only the

zone currently selected.

$lf,l'o"o c

Monitor the temperatu re

of a zone. The MONITOR/SCAN light

stays on.

Place the system in

standby. The STANDBY light turns on.

The STANDBY light turns off.

Heating zones hold at

your preset standby

temperatures.

Heating zones return to

your operating setpoint

temperatures.

Take the system out of

standby.

STANDBY $o

Turn the heaters on The HEATERS light turns on.

The HEATERS light turns off.

The tank, hoses, and

guns are heated.

No heat is applied to

system components.

Turn the heaters off. HEATEHS @ o

Turn the 7-day clock on. The CLOCK light turns on. The system performs

functions controlled by

the clock.

The system does not

perform functions

controlled by the clock.

CLOCK

Turn the 7-day clock off. The CLOCK light turns off

Turn the pump on The PUMP light turns on. The pump draws melted

materialthrough the

system.

The pump stops drawing

melted material through

the system.

Turn the pump off PUMP The PUMP light turns off

"Fo

Determine whether a

fault was corrected. All LED lights turn on white

the system begins a

five-second test. At the end

of the test, the FAULT light

turns off.

All LED lights turn on while

the system begins a

five-second test. At the end

of the test, the FAULT light

stays on.

The fault was corrected.

The fault was not

corrected.

PlEti. A

original copyright dale 2/92. Nordson is a registered trademark of Nordson corporation.

o 1 E N-O PC-[3V -2297771-1 lssued 4/98

Vista Contro! Panel

1. Zone indicator lights

2. STANDBY or SETPOINT temperature light

3. SYSTEM SETTINGS light

4. Up key for system settings

5. Down key for system settings

6. Move right key

7. Clock INTEFIVAL lights

10 I

8. POWER switch

9. Clock feature lights

10. Control keys

11. Control lights

12. Up key for selector display

13. Up key for multipurpose display

14. Selector display

15. Multipurpose display

16. FAULT light

17. READY light

18. Actual temperature display

19. Down key for multipurpose

display

20. Enter key

15 16 17

Vista* FAULT J

AREADY

I50F )5tF

Of *,-*

Olo^-rt EEfE

D{IEMI HE Ot'}I

IEMPERAIUR€ rl

1-u

SYSIEM

SEINNGS

OQe**.

o!Iffi*

z'r flz un

\-/ l- srmw

O @ *'o"*

O @ *ro"o*

INTERVAL

'61

\y'2

O qocK

POWER

sr "rrr $ O

CLOCK

CLEAR

FAULTS &

PUMP

o 1 E N-O PC-[3V -2297 77)-1 lssued 4/98

Record of Vista Control Settings

Temperature Settings

Zone

Type

lnternal

Hose

Gun

Zone

Type

Hose

Gun

Clock Settings

Zone 1 Temperatures Zone2 Temperatures Zone 3 Temperatures

Zone 6 Temperatures

Band

Operating Standby

Operating Standby Band

Zone 5 Temperatures

Zone 4 Temperatures Operating Standby

Operating Standby Band

Heater lntervals Monday Tuesday Wednesday Thursday Friday Saturday Sunday

Heaters On-1

Heaters Off-1

Heaters On-2

Heaters Off-2

Standby lntervals

Standby On-1

Standby Off-1

Standby On-2

Standby Off-2

System Settings

System ready time delay:

Overtemperature setpoint

Pump air pressure:

Global temperature band:

Auto-energize pump

temperature setting:

Startup: tr Sequential / tr Simultaneous

Auto-energize heaters: tr On / ! Off

Auto-energize pump: tr On / tr Off

Warning or power output: tr Warning / E Power on

Ready or pump output: tr Ready / E Pump on

Password: trOn/trOff

lssued 4/98 o 1 E N-O PC-[3V -2297771-1

lntroduction

Series 3000 V Manual Configuration Code

1. Product Configuration

Codes

2. Understanding Your

Manual Configuration

Code

The configuration code indicates the features included in your system

as shipped. Your system and its manual have similar, but not identical,

configuration codes.

The system configuration code appears on the lD plate on the unit.

Please refer to this code when contacting Nordson to order services or

parts.

The manualconfiguration code appears on the title page and on the

spine of your product manual. This code ensures that the manual you

receive contains information about your system.

Use the following example to interpret the configuration code for your

product manual.

- Voltage

Pump

Model

Manifold

f Controller IOption

M3400V X EAV:. f,.1:: Ix

Model Voltage Pump Manifold ControllerType Options

31 00y

3400v

3500v

3700v

3830v

3860v

3890v

3930v

3960v

X Voltage code

1,2, or 3

4 Voltage code 4

D Single-acting

10:1 piston pump

E SP3O

14:1 piston pump

F SP3O

21:1 piston pump

G SP3O

6:1 piston pump

K AC gear pump

200 volt

L AC gear pump

240 volt

A 4-port

B 6-port

C 6-port reverse-flush

J 4-port, w/pressure control

valve

S 1 supply port, 1 return port

T 1 supply port, 1 return port,

reverse-flush

V Vista

P Pattern

T Temperature

X alloptions other

than EMC

4 EMC

NOTE: Shaded area denotes data not pertinent to the manual configuration code.

@ '1999 Nordson Corporallon

All riqhts reserued 41-3000y

lssued 2/99 ol EN-02-[3V-CONFlG]-1

Otros manuales para 3100V Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Máquina de fusión de Nordson

Nordson

Nordson 2302 Manual de usuario

Nordson

Nordson ProBlue Flex Manual de usuario

Nordson

Nordson 3500V Series Manual de lista de piezas

Nordson

Nordson 3400 Manual de usuario

Nordson

Nordson AltaBlueA4TP Guía de referencia

Nordson

Nordson ProBlue 1028303 Manual de usuario

Nordson

Nordson ProBlue P4 Guía de referencia

Nordson

Nordson 3930 Manual de usuario

Nordson

Nordson Mesa Fulfill Guía de referencia

Nordson

Nordson EP 30 Manual de usuario

Nordson

Nordson PURBlue 7156681A Manual de usuario

Nordson

Nordson ProBlue Flex Manual de usuario

Nordson

Nordson DuraDrum Manual de usuario

Nordson

Nordson VersaBlue VBN 50 Manual de usuario

Nordson

Nordson ProBlue Flex Manual de usuario

Nordson

Nordson 3500 Series Manual de lista de piezas

Nordson

Nordson 3100 Manual de usuario

Manuales populares de Máquina de fusión de otras marcas

Bibby Sterilin

Bibby Sterilin Stuart SMP10 Manual de usuario

Meler

Meler Cantho Manual de usuario

Buchi

Buchi M-565 Manual de usuario

Indutherm

Indutherm MU200 Manual de usuario

GOLDBRUNN THERM

GOLDBRUNN THERM Goldbrunn 1000 Manual de usuario

SCS

SCS Good COOKING Chocolate Melting Pot Manual de usuario

Cole Parmer

Cole Parmer MP-400 Series Manual de usuario

CIMLINE

CIMLINE MATRIX 1500 Manual del propietario

Graco

Graco THERM-O-FLOW T7 Series Manual de usuario

VALCO MELTON

VALCO MELTON D4-L Manual de usuario

Meler

Meler MACRO 200 Manual de usuario

Viega

Viega ProRadiant Basic Digital Snow Melt Control... Hoja de instrucciones

Rapid

Rapid EG PEN Manual de usuario

CIMLINE

CIMLINE MATRIX 1500 Manual del propietario

UES

UES perfectMelt Manual de usuario

PRECIOUS PLASTIC

PRECIOUS PLASTIC INJECTION Manual de usuario

VALCO MELTON

VALCO MELTON D10 Manual de usuario

VALCO MELTON

VALCO MELTON D4-E Manual de usuario