Nokia NPD-1 Series Guía
CCS Technical Documentation
NPD-1 Series Transceivers
Issue 1 11/2002 Confidential Nokia Corporation
Troubleshooting — Antenna
NPD-1
Troubleshooting — Antenna CCS Technical Documentation
Page 2 Nokia Corporation Confidential Issue 1 11/2002
CCS Technical Documentation Troubleshooting — Antenna
NPD-1
Issue 1 11/2002 Nokia Corporation Confidential Page 3
Contents Page No
Troubleshooting - Antenna ............................................................................................ 5
Relevant Documents ................................................................................................. 5
Failures and Corrective Measures ...............................................................................5
Internal antenna not installed or unplated internal antenna installed........................ 5
Stamped contact spring clips missing/miss-installed for internal antenna................ 5
Bottom antenna clip bent or missing......................................................................... 6
Missing whip............................................................................................................. 6
Ungrounded display frame........................................................................................ 7
NPD-1
Troubleshooting — Antenna CCS Technical Documentation
Page 4 Nokia Corporation Confidential Issue 1 11/2002
CCS Technical Documentation Troubleshooting — Antenna
NPD-1
Issue 1 11/2002 Nokia Corporation Confidential Page 5
Troubleshooting - Antenna
This troubleshooting guide addresses potential failures that will affect the antenna per-
formance of the phone, and discusses methods for correction of these failures.
Relevant Documents
For additional information, refer to the Eagle Antenna Electromechanical Specifications
(DMS03311-EN-2.0) and the Eagle Antenna Module VQD (DMS00188-EN-1.2).
Failures and Corrective Measures
Internal antenna not installed or unplated internal antenna installed
A properly installed and plated Eagle antenna module is shown in Figure 1.
The Eagle antenna module consists of the internal antenna and whip antenna as one
module.
Figure 1: Eagle Antenna Module installed)
If the Eagle antenna module is missing, install one. If an unplated internal antenna is
installed, replace it with a properly plated internal antenna module.
If no internal antenna is installed, the antenna gain will be degraded by more than
25 dB.
Stamped contact spring clips missing/mis-installed for internal antenna
Figure 2 shows the RF feed and ground stamped contact spring clips properly installed.
Figure 3 shows both stamped contacts spring clips missing. If the either contact is miss-
ing or bent, replace antenna module with new antenna.
Figure 2: RF feed and ground stamped contact spring clips properly installed
NPD-1
Troubleshooting — Antenna CCS Technical Documentation
Page 6 Nokia Corporation Confidential Issue 1 11/2002
Figure 3: Stamped contact spring clips missing
Bottom antenna clip bent or missing
The bottom antenna clip is located near the bottom of the phone in the D-cover. A prop-
erly installed bottom antenna clip is shown in Figure 4.
Figure 4: Properly installed bottom antenna clip
If the bottom antenna clip is bent or missing, then it should be carefully replaced with a
new one.
The degradation in antenna performance is only about 2 to 4 dB in the receive portion of
the CELL band when the whip is retracted. PCS band, retracted whip, degradation will be
10 to 15 db.
Missing whip
If the whip is missing, then the Eagle antenna module should be replaced. Figure 5
shows a properly installed whip antenna.
CCS Technical Documentation Troubleshooting — Antenna
NPD-1
Issue 1 11/2002 Nokia Corporation Confidential Page 7
The whip will perform 2 dB better than the internal antenna in free space. The whip will
perform up to 3 dB better than the internal antenna in talk position.
Figure 5: Properly installed whip antenna
Ungrounded display frame
The display frame is normally grounded by two spring clips (Figures 6). The figure shows
the display frame grounding locations. If clips are missing or bent, replace light guide
with good one. SAR performance will degrade by .5 mW/g for one leg not grounding to
the PWB to over 1.7mW/g if both legs are not grounded.
Figure 6: Display frame grounded by two spring clips
The D cover and light guide have snaps near the display frame ground positions. Make
sure they are locked in position for ESD protection. These snap features help maintain
display leg contact with the PWB.
NPD-1
Troubleshooting — Antenna CCS Technical Documentation
Page 8 Nokia Corporation Confidential Issue 1 11/2002
Otros manuales para NPD-1 Series
4
Tabla de contenidos
Otros manuales de Teléfono móvil de Nokia
Nokia
Nokia 3310 3G Manual de usuario
Nokia
Nokia G100 Manual de usuario
Nokia
Nokia 2126i Manual de usuario
Nokia
Nokia 1265 Manual de usuario
Nokia
Nokia 3208c Manual de usuario
Nokia
Nokia C2-01 Guía del usuario
Nokia
Nokia 6560 Manual de usuario
Nokia
Nokia 305 Manual de usuario
Nokia
Nokia 5100 - Cell Phone 725 KB Manual de usuario
Nokia
Nokia COMMUNICATOR 9110 Guía de inicio rápido
Nokia
Nokia 2710 Manual de usuario
Nokia
Nokia 2355 Manual de usuario
Nokia
Nokia E55 Manual de usuario
Nokia
Nokia 2720 Manual de usuario
Nokia
Nokia EDICIN 2 6350 Guía del usuario
Nokia
Nokia 500 Manual de usuario
Nokia
Nokia SLIDE 6600I Manual de usuario
Nokia
Nokia 3320 Manual de usuario
Nokia
Nokia 6235 Manual de usuario
Nokia
Nokia 6103 - Cell Phone 4.4 MB Manual de usuario
