(2)Check damaged paris
Belore further use ofthe too an accessory or other
partthatis damaged should be carefuly checked lo
determine that ,l wil operate propery and perorm
ts intended Funct ons
Check lor a19nment of mOvinO parts, bindino oi
moving parts,breakage ol parts, mouning and any
other cond ilons thai may arrect ts Operal on
An accessory or olher part that is damageO or
inoperable should be proper y repa red or replace0
(3)Repalrs by author12ed personnel
Any repairs on the tool o「
instalal oo ol replacement
parts shou10 be periormed only by the sales agent
irom whom you purchased the tool or an author ze0
dealer use only genuine replacement parts
Falure to utize the experise oi the sales agent
irom、vいom you purchased the tool or an author zed
dealer or.lalure to use oenuine replacement parts,
may iesun an ncreased lsk oi niury to the user
and may lnvaldate your warranty
(4)uSe recOmmended accessories
Consu t this manual or the sales agent irOm
ヽVhom
you purchased the tool or an author zed dealer ior
recommended accessor es The use ol lmprOper
accessoles may cause nsk oi nlury to persons
(5)Always turn off the alr supply and dlsconnect
the alr supplyぃ。se before lnsta‖lng,removlng
or adlusting any accessory On the tool or
before performlng any malnlonance ollhe tool
(6)Do not removo anソ !abols or namepldes,rom
the tool
lf a label or nalmeplate has been damaged of is
missing cOntact the sales agent irom whom you
purchased the tool or an author zeO dealer io obtain
a replacement
3‐l Air Pressure
AI「
pressure largely Oetermines lool performance
This toolis desioned to be operated at a r pressure
of0 59 MPa(6k911cm2′ 85PS′ 5 9 bar)max mum
3‐
2 Air Line[F10 1]
Use a 95 mm (3′ 8') ar hOSe between the
compressor and the tool Compressed a r is cooled
and ts diain separated, as soon as the ar leaves
the compressor The drain, ho、 vever is condensed
in the plpin。
, and can enter the tool mechanism,
and may cause trouble So,instal an a rflter and an
oler betヽVeen the compressor and the tool
A,Fl er
Ar Re9JIol。
' 。ler
高
4ム
￨￨
=48品
朧
s,
Toot r i「
IF0 1〕
Thls tool ls ior dr‖‖ng work
Tapplng (rlght‐hand screw)ls
uslng the reversible function
3‐3 Lubricatlon iFi0 1〕
An oler should bo insta‖ed betwoon the
compressor and the too Use mach no ol oSO VG
10) NeOlecing the ol supply wIl cause damaoe
Since tho use oi thlok 。
l w‖￨ lead lo poor
periormance,a ways uso maCh no ol oSO VO■
0)
△WARNING
・
Wear prOtective glasses and earpiugs during
drilling Operation For the operation producing
much dust,wear an antidust mask
・
Wear cotton work gloves or vibration― proof
gloves tO prOtect your hands against vibrations
and chips
・
Nevertouch moving palts
・
When the dri‖ passes througぃ or locked during
drilling Or tapping,the main body may be swung
around lf it occurs,release the Trigger quickly
to avoid inlury Do not tap a b:ind hole using
this air drill
・
Do not use the exhaustfor air blow operation
△ CAUtt10N
・
For tapping,always use tapping paste
・
use sharp taps
・
use a tapertap(No l)and a plug tap(No 2)for
tapping
wnh a d ‖ b‖
a:so posslbl● by
Check the contents and make sure thatthe tool does
not have any damege due to an aceideni durnO the
transpOrtat on, f any The contenis should correspOnd
lo the accessor es on the parts lst Jusiin case there
are some damages or missing paris,contactthe sales
aOeni from 、vhom you purchased the tool or an
author zed dealer
3
