Nippon Genetics Europe FastGene Manual de usuario

FastGene

High Speed Mini Centrifuge

Cat.No.: NG003

2013 August / Rev. 01

HighSpeed Mini Centrifuge

CONTENTS

Page

General Information 2

1.2

First QC Check 2

2.1

Packaging Content 2

3.1

Meanings of Symbols 3

3.2

Safety Precautions 3

Product Description & Technical Specifications 5

Installation 6

Operation 8

Maintenance 11

Transportation 11

Trouble Shooting 12

9.1

Error Codes 13

Rotor and Accessories 14

Ordering Information 14

Contact Information 15

1.1 GENERAL INFORMATION

Thank you for purchasing FastGene

High Speed Mini Centrifuge. This Manual includes the operation procedure. In order to

use the instrument properly, please read this manual carefully before using the instrument.

This centrifuge is designed for workstations in research laboratories in the fields of bioscience, medicine and chemistry. Twelve

1.5 ml or 2.0 ml micro test tubes can be centrifuged simultaneously in a 45°fixed-angle rotor.

1.2 FIRST QC CHECK

Please check the instrument and the packing list when you open the package. If you find there is something wrong with the

instrument or the packaging content, please contact Nippon Genetics Europe or your distributor in your country.

2.1 PACKAGING CONTENT

FastGene

High Speed Mini Centrifuge NG003

12 x 1.5/2.0 ml tube rotor 1

Rotor nut 1

Rotor lid 1

Adaptors for 0.5 ml tubes 12

Adaptors for 0.2 ml tubes 12

Operation Manual 1

Power Cord 1

HighSpeed Mini Centrifuge

3.1. MEANINGS OF SYMBOLS & SAFETY PRECAUTIONS

Symbols on the device

Symbol Meaning Symbol Meaning

Indicate a hole for

manual door opening in

case of emergency

Attention and warning for

electric shock

Attention and warning for

rotor coupling

Attention and warning for

door opening and closing

Symbols in this document

Symbol Meaning Symbol Meaning

This symbol refers to safety

relevant warnings and indicates

possible dangerous outcomes

☞ Note.

This symbol refers to the important

reminder

3.2. SAFETY PRECAUTIONS

Before using the instrument, please read this operation manual to ensure correct usage. Incorrect handling of the instrument

could possibly result in personal injury or physical damage on the instrument or its accessories.

1. ALWAYS locate the instrument on a flat, rigid and stable table capable of withstanding the weight of the instrument and its

spinning operation.

2. ALWAYS make a safety zone of 30 cm around the centrifuge to indicate that neither hazardous materials nor persons

should be permitted within the area during operation. ALWAYS position the instrument with enough space on each side of

instrument to ensure proper air circulation.

3. ALWAYS install the instrument within a temperature and humidity controlled environment. (Permissible ambient

temperature: +5°C ~ +35 °C, Relative humidity: ≤85%)

4. Before connecting the power, check the rated voltage.

5. Should not use unapproved rotors and associated accessories. Only use rotors from NIPPON GENETICS EUROPE with

appropriate centrifugal tubes and suitable adaptors to embrace sample containers tightly enough inside rotors.

6. Before operating the instrument, check if the rotor and the rotor lid are securely fastened. Should operate the instrument

with a rotor properly installed and secured to the motor shaft.

7. Mount the rotor on the motor shaft properly, check it with spinning manually.

8. Do not stop the rotor by touching with hand during the instrument is running.

9. Emergency door open should be performed only when spinning is completely stopped.

HighSpeed Mini Centrifuge

10. Should not exceed the rated speed or specific gravity. Samples whose density is greater than 1.2g/ml must have reduced

maximum rotational speed to avoid rotor failure.

11. The sample content should not exceed 80% of total capacity of a tube. Otherwise, it would cause spillage of sample fluid

and even the tube breakage.

12. ALWAYS load the tubes symmetrically with evenly weighted samples to avoid rotor imbalance. If necessary, use the water

blank to counterbalance the unpaired sample.

13. The operation speed should not exceed the highest value of the individual guaranteed g-forces of each centrifuge, rotor,

bucket or adaptors and sample container, especially the guaranteed g-force of sample container should not be neglected.

14. The rotors should be cleaned and kept dry after every use for longer life and safety.

15. ALWAYS disconnect the power supply prior to maintenance care and service to avoid electrical shock.

16. ALWAYS use proven disinfection procedures after centrifuging bio hazardous materials.

17. Should not centrifuge flammable, toxic, radioactive, explosive, or corrosive materials.

18. When it is necessary to use toxic or radioactive materials or pathogenic micro-organisms which belong to the Risk Group II

of WHO: “Laboratory Bio- safety Manual,” should follow national regulations.

Do not place dangerous materials within 30 cm distance around the instrument, and that is also

recommended by IEC 61010-2-020.

Use the emergency door open function only when the [Door] button on the control panel is dumb under

the condition of complete stop of rotor running.

Never try to open or move the instrument if it is not completely stopped.

If the power input is more than +/- 10% of the recommended voltage or fluctuates frequently, it may

cause malfunction of the instrument and often result serious damage.

Install the instrument at the place without any kinds of corrosive gases.

HighSpeed Mini Centrifuge

4. PRODUCT DESCRIPTION & TECHNICAL SPECIFICATIONS

Max. RPM/RCF

(Rotor)

13,500 rpm/ 12,300 xg

(Fixed Angle)

6,000 rpm/ 1,850 xg

(PCR Strip Rotor)

(optional accessory)

Max. capacity 12 x 2.0 ml or 1.5 ml Tubes 4 x 8-well PCR Strips

Time control Pulse or timed ≤30 min

RPM/RCF conversion Yes

Noise level (dB) ≤56

Acc/Dec (sec) ≤12 / < 16

Display Blue LCD

Automatic door release at completion Yes

Power supply (V/Hz) 220/50~60 (110V optional)

Power requirement(VA) 110

Dimension (W x D x H, mm) 208 x 245 x 145

Weight without rotor (kg) 4.4

CE mark Yes

Cat. No. NG003

HighSpeed Mini Centrifuge

5. INSTALLATION

Power On/Off

1. Connect the AC Power cord at the power socket on the back of the instrument.

2. Turn on the instrument by pressing the switch on the back of the instrument.

Door Release

1. For opening the door, press the [DOOR] button.

The door is automatically opened after completion of spinning operation with

beeping sound.

When you close the door, close it until hearing clank shut.

☞

The door is not opened while the instrument is running.

If the door is opened, the instrument could not be operated even with pressing the [Start] button.

Power Failure: If there is any power failure during the operation, door is not opened with [Door] button. Door

can be opened only when the operation is completely stopped and the power is on again. If you want to

open the door at the power failure, please refer to 6. Emergency Door Open (page 10).

Rotor Coupling and Disassembling

Before coupling a rotor, clean the motor shaft and chamber with soft dry towel.

Fixed Angle Rotor

1. Mount a proper rotor into the motor shaft.

2. Place the Rotor Locking Nut at the center hole of the rotor.





To assemble the rotor: Rotate the Rotor Locking Nut clockwise

until tightly assembled.





To disassemble the rotor: Rotate the Rotor Locking Nut counterclockwise.

3. After loading sample tubes, close the rotor lid until hearing clank shut.





To open the lid, lift the nut.

HighSpeed Mini Centrifuge

8-well strip Rotor

1. Mount a proper rotor into the motor shaft.

2. Place the Rotor Locking Nut at the center hole of the rotor.





To assemble the rotor: Rotate the Rotor Locking Nut clockwise until tightly assembled.





To disassemble the rotor: Rotate the Rotor Locking Nut counterclockwise.

When the PCR rotor is coupled, please do not speed over 6,000 rpm / 2,400 rcf,

as mentioned on the rotor.

Positioning of Sample Tubes

1. Before loading sample tubes, check the water drop or dirt in the rotor hole or inner adaptor.

2. If there is a water drop or dirt in the rotor hole or inner adaptor, remove it with soft dry cloth.

3. Tubes should be placed in the rotor with same amount of samples at symmetrical positions.

4. Only use appropriate centrifugal tubes and do not exceed the speed beyond the tube’s max g-force.

5. For safety, fill the sample for 70~80% in the tubes.

Correct Ways of Sample Balancing & Tube Usage

☞

If the number of samples is not in pair, please load the control tubes at each symmetrical position. Otherwise, it results

noise and vibration, which eventually damage the instrument.

HighSpeed Mini Centrifuge

6. OPERATION

Display Window

Shows speed, time, status of running and the status of door opening or closing.

RPM/RCF Modes are displayed as rpm ot rcf.

While running, is flickering.

appears when the Door is opened and appears when the Door is closed.

Time is displayed as ‘min’.

Setting Buttons

When setting up the RPM/RCF and Time, you can put the set value with up (▲) and down (▼) button.

Function Buttons

[Door] For opening instrument door

[Pulse] For quick spin down



[Start/Stop] Commend start and stop operation

Setting the RPM/RCF Value

Maximum RPM/RCF: 13,500 RPM/ 12,300 x g

Display value: multiply 1,000 to check real value. (Example: RPM Display value 13.5 indicates RPM 13,500)

HighSpeed Mini Centrifuge

Setting

the RPM Value

1. Press the [RPM/RCF] button once to adjust RPM.

RPM LED is flickering on the display window, indicating that the instrument is in the RPM Mode.

2.Press the [

▲▼

] buttons to change input value.

RPM setting unit: 0.1 unit (0.1=100rpm)

After 5 seconds from pressing the input value, the setting value is saved.

If you want to check the input value, press [RPM/RCF] button.

If you do not press the [

▲▼

] button for 5 seconds, the setting mode is cleared.

Setting the RCF Value

1. Press the [RPM/RCF] button twice to adjust RCF.





RCF LED is flickering on the display window, indicating that the instrument is in the RCF Mode.

2. Press the [▲▼] buttons to change input value.





RCF setting unit: 0.1 unit (0.1=100 rcf)





After 5 seconds from pressing the input value, the setting value is saved.





If you want to check the input value, press [RPM/RCF] button.





If you do not press the [▲▼] button for 5 seconds, the setting mode is cleared.

When the PCR rotor is coupled, please keep in mind that do not over speed at the max. 6,000 rpm/2,400 rcf,

as mentioned on the rotor.

HighSpeed Mini Centrifuge

Setting the Time Value

Time control: 1 min. ~30 min ; Time setting unit: 1min

1. Press the [TIME] button once.

‘min’ on LED is flickering.

2. Press the [▲▼] buttons to change input value.

After 5 seconds from pressing the input value, the setting value is saved.

If you do not press the [▲▼] button for 5 seconds, the setting mode is cleared.

Start/Stop

1. After setting RPM/RCF and Time, press [Start/Stop] button.

The running starts only when the door is closed.

In case of pressing the [Start/Stop] button while running, the running is

stopped.

Pulse

Button for quick spin down

1. If you press [Pulse] button and release at the point you want to stop, the centrifuge

decelerates immediately.

When the running is stopped, the door is opened automatically with beeping

sound.

Emergency Door Open

The door can be unlocked manually with Emergency Door Open Function.

1. After pulling the instrument forward about 10 cm, find the “Emergency Door Open Hole”

at the bottom of the instrument

2. Insert spikes (a car key, scissors, etc.) 2~3 cm into the “Emergency Door Open Hole”

and pull the spikes at the opposite direction of the arrow.

Manual opening should be performed only when spinning is completely stopped. Otherwise, harmful

damage will be accompanied to not only operators but samples.

After opening the door manually, it is recommended to wait until normal electricity comes back.

Otros manuales para FastGene

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de laboratorio de Nippon Genetics Europe

Nippon Genetics Europe

Nippon Genetics Europe FastGene Manual de usuario

Nippon Genetics Europe

Nippon Genetics Europe FastGene PG01 Manual de usuario

Nippon Genetics Europe

Nippon Genetics Europe FastGene NG020 Manual de usuario

Nippon Genetics Europe

Nippon Genetics Europe FastGene FG-09WS Manual de usuario

Nippon Genetics Europe

Nippon Genetics Europe FastGene CapEasy Manual de usuario

Nippon Genetics Europe

Nippon Genetics Europe FastGene FAS-Nano GP06-LED Manual de usuario

Nippon Genetics Europe

Nippon Genetics Europe FastGene FAS-DIGI PRO Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario